TELEVAC DS-10 Bedienungsanleitung

Remote Digital Display Unit

DS-10

2-7900-098

Instruction Manual

TELEVAC

A DIVISION OF THE FREDERICKS COMPANY

2400 PHILMONT AVE.

HUNTINGDONVALLEY, PA 19006

SUNSTAR传感与控制 http://www.sensor-ic.com/ TEL:0755-83376549 FAX:0755-83376182 E-MAIL:[email protected]

1. Installation

Panel thickness:1 -10 mm





9.2

8.2

100

61.6

44.8

48

(Unit: mm)

48

DS-

10

25

45

+0.6

0

L1

n: number of unit (2

≦n≦

6)

45

L1=(48×n-3)

44.8

25

+0.6

0

45

+0.6

0

SUNSTAR传感与控制 http://www.sensor-ic.com/ TEL:0755-83376549 FAX:0755-83376182 E-MAIL:[email protected]

2. Wiring

function

IN/OUT

explanation

1 ＋24V INPUT 24V DC Input

2 ＋24V COM 24V DC Common

4 SP1

OUTPUT

Setpoint 1 Common

5 SP1 NO Setpoint 1 NO

6 SP1 NC Setpoint 1 NC

７SP2

OUTPUT

Setpoint 2 NO

８SP3 Setpoint 3 NO

９SP2, SP3 COM Setpoint 2,3 Common

１１ ANALOG IN＋INPUT Analog Input +

１２ ANALOG IN－Analog input -

24V

NO

10

NO

0～10V

－

SP1

NO

NC

＋

－

＋

DC

13

14

15

18

16

17

3

6

5

4

2

1

12

11

9

7

8

SP3

SP2

SUNSTAR传感与控制 http://www.sensor-ic.com/ TEL:0755-83376549 FAX:0755-83376182 E-MAIL:[email protected]

3. Specification

Display

Main display

:

4 digit LED(Green)



display range

:

4.0

×

10-13

～

4.0

×

107

(0.3 to 10.3Vinput)

Display= 10{(V-6.5)/0.5}

over scale

:

“oooo” blinking when input is over 10.3V

under scale

:

“uuuu” blinking when input is under 0.3V

Sub display

:

4 digit LED(orange) charctor dispaly

:

set points status indicator (point LED Green)

Input signal

Input voltage

:

DC 0-10V

Sampling interval

:

0.5sec

Input impedance

:

5.1kohm

Setpoint

Setpoint 1

:

AC250V 3A ,1c contact

Setpoint 2,3

:

AC250V 1A ,1a contact

Ambient

Temperature

:

0 - 50

℃

Humidity

:

45 -85%RH

Power

Input voltage

:

DC21.6 - 26.4V(nominal 24V)

power consumption

:

max 160mA

physical property

weight

:

150g

size

:

48

×

48

×

100mm

SUNSTAR传感与控制 http://www.sensor-ic.com/ TEL:0755-83376549 FAX:0755-83376182 E-MAIL:[email protected]

4. Panel description

Function

Description

1 : Data display(green)

data and parameters are displayed

2 : Mode display(orange)

parameters are displayed

3: Setpoint indicator(red)

（SP1, SP2, SP3）

Lit when pressure went below the setpoints

4: Set key

call and enter parameters

5: Shift key

move display digit

6: Down key

decrease displayed values

7: Up key

increase displayed values

5. Operation

When power is turned on model number and software version number are displayed for 4 seconds

then go to measure mode.

4 seconds

DS- 10

SET

SP2SP1 SP3

×10

SET

SP1 SP2 SP3

DS- 10

×10

SP1

SET

DS- 10

×10

SP3SP2

model number

soft version

measure mode

SP3

③

①

×10

SP1 SP2

SET

⑥

②

⑤④

DS- 10

⑦

SUNSTAR传感与控制 http://www.sensor-ic.com/ TEL:0755-83376549 FAX:0755-83376182 E-MAIL:[email protected]

5. Operation (cont.)

(1) Measure mode

3.2

×

102Pa

3.2

×

10-2 Pa

(2) Program mode

Push set key for program mode. Use shift key to move changing digit. Use up

and down key to change the value. Push set key to register the value.

Ex. Change SP1H from 2.0×10-2 to1.0×10-2

Pushset key and the unit goes to program mode

measuremode

Program mode

1. Blinking digit can be changed. Push shift key to move changing digit.

2. Push down key to change the value from “2” to “1”

3. Push set key to register the value. The unit automatically move to the next parameter.

×10

DS- 10

SP1 SP2 SP3

SET SET

SP1 SP2 SP3

DS- 10

×10

DS- 10

SP1 SP2 SP3

SET

DS- 10

SP3

SP2SP1

SET

×10

SET

SP3SP2SP1

DS- 10

SP1

SET

DS- 10

SP3SP2

×10 ×10

SP3

×10

SP1 SP2

SET

DS- 10

SP3SP1

×10

SP2

DS- 10

SET

SUNSTAR传感与控制 http://www.sensor-ic.com/ TEL:0755-83376549 FAX:0755-83376182 E-MAIL:[email protected]

Parameters

In program mode the following parameters are displayed one by one by pushing set key.

charactor parameter

SP1

upper threshold

SP1H

SP1

lower threshold

SP1L

SP2

upper threshold

SP2H

SP2

lower threshold

SP2L

SP3

upper threshold

SP3H

SP3

lower threshold

SP3L

digital filter

dF

SET

SP1 SP2 SP3

DS- 10

×10 ×10

SET

SP3SP2

SP1

DS- 10

SUNSTAR传感与控制 http://www.sensor-ic.com/ TEL:0755-83376549 FAX:0755-83376182 E-MAIL:[email protected]

RAM Error

Reset by power off

blink data

over input data range

“0000”

Blinking

Over scale

“uuuu”

Blinking

Under scale

SUNSTAR传感与控制 http://www.sensor-ic.com/ TEL:0755-83376549 FAX:0755-83376182 E-MAIL:[email protected]

TELEVAC DS-10 Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken