Telma TL113005 Bedienungsanleitung
17feb12jh
TL113005
INSTALLATION MANUAL
FOR
TELMA AC50-55
ON FORD E-350/450 CUTAWAY
WITH TELMA CONTROL MODULE
TL113005
Ford E-350/450 Cutaway Installation Manual with Telma Control Module (TRCM)
Page 2 of 30__________________________________________________________________________17feb12jh
TABLE OF CONTENTS
1 Preparation of the Chassis
1.1 Driveline
1.2 Exhaust
2 Telma Installation
2.1 Installation Kit TIK10677
2.2 Install the Chassis Brackets
2.3 Install vent tube extension
2.4 Assemble the Telma Brackets and mounts
2.5 Install the Telma in the Chassis
2.6 Drive Shaft Modification and Installation
2.7 Axle Shim Installation
3 Control Components
3.1 Relay Box Installation
3.2 Light Bar Installation
3.3 Telma Control module and Foot Control Switch Installation
3.4 Foot Switch Adjustment
4 Wiring Harness Installation
4.1 Power Harness Installation
4.2 Control Harness Installation
4.3 Wiring Diagram
5 Recommended Tools
6 Post Install Checklist
Appendix
(1.1) E350 138” WB with 5.4L engine
(1.2) E350 138” WB with 6.0L/6.8L engine
(1.3) E350/450 158” WB with 5.4L engine
(1.3.1)E350/450 158” WB with 6.0L/6.8L engine
(1.4) E350/450 176” WB with 6.0L/6.8L engine (X1=24)
(1.4.1) E350/450 176” WB with 6.0L/6.8L engine (X1=22.5 / L1= original)
(1.4.2) E350/450 176” WB with 6.0L/6.8L engine (X1=10)
(1.4.3) E350/450 158 to 176” WB with 6.0L/6.8L engine (stretch in front of x-member)
(1.5) E350/450 186” WB with 6.0L/6.8L engine (stretched chassis)
(1.5.1) E350/450 158 to 186” WB with 6.0L/6.8L engine (stretch in front of x-member)
(1.6) E350/450 190” WB with 6.0L/6.8L engine (stretched chassis)
(1.6.1) E350/450 158 to 190” WB with 6.0L/6.8L engine (stretch in front of x-member)
(1.7) E350/450 208” WB with 6.0L/6.8L engine (stretched chassis)
(1.7.1) E350/450 158 to 208” WB with 6.0L/6.8L engine (stretch in front of x-member)
TL113005
Ford E-350/450 Cutaway Installation Manual with Telma Control Module (TRCM)
Page 3 of 30__________________________________________________________________________17feb12jh
SECTION 1 PREPARATION OF THE CHASSIS
1.1 DRIVELINE
Remove the complete drive-line assembly from the transmission flange yoke to the rear axle flange yoke.
1.2 EXHAUST
There should be no exhaust modification necessary for any wheelbase other than 138. A shorter replacement muffler
is necessary for E350 138” wheelbase.
SECTION 2 RETARDER INSTALLATION
2.1 INSTALLATION KIT TIK10677
P/N DESCRIPTION QTY
CN201155 AC50-55 / 12V (1410-1550) 1
TIB03123 LEFT SIDE RETARDER BRACKET (4.5 DEGREE) 1
TIB03124 RIGHT SIDE RETARDER BRACKET (4.5 DEGREE) 1
TIB03127 FORD E350-450 CHASSIS BRACKET 2
JZ100280 SIDE PLATE FASTENERS 1
JZ1007XX-30 TELMA SHOCK MOUNT SET (30 SHORE) 1
VF120340 ALL METAL LOCKNUT ½-20UNF G8 8
TIF03003 NUT 9/16 - 12 UNC G8 6
TIF03005 LOCKWASHER 9/16 G8 6
TIF04001 BOLT 9/16 - 12 UNC X 2 HEX HEAD G8 6
TID11050 HARNESS W/ JD331121 1
TIB01017 CONTROL / RELAY BOX BRACKET 2
TIG31063 TELMA CONTROL MODULE FORD CAN 1
TIB05002 FORD E350-450 PEDAL CLAMP 1
TIB05046 FORD E350-450 FOOT SWITCH BRACKET 1
TIB05047 FORD E350-450 PEDAL BRACKET 1
JC120102 FOOT SWITCH 1
TIG11010 TELMA LIGHT BAR DISPLAY 1
TIF05021 MUSIC WIRE / RETURN SPRING 1
TIF05000 LOCKWASHER 1/4 SPLIT 6
TIF05002 NUT 3/8 - 16 UNC G5 2
TIF05003 LOCKWASHER 3/8 G5 SPLIT 1
TIF05004 NUT 1/4 - 28 UNF G8 6
TIF05005 BOLT 1/4 - 28 UNF X ¾ HEX HEAD G8 6
TIF05010 LOCKWASHER 5/16 SPLIT 4
TIF05011 NUT 5/16 4
TIF05012 BOLT 5/16 - 18 UNC X 1-3/4 HEX HEAD G5 4
TIF05013 BOLT 1/2 - 13 UNC X 1-1/2 HEX HEAD G5 2
TIF05014 LOCKWASHER ½ MED SPLIT 2
TIF05019 ELEVATOR BOLT 3/8 - 16 UNC 2-1/2 1
TIF05034 FENDER WASHER ¼ X 1 1
JZ100110 DISCHARGE ASSEMBLY 1
Note: 1410 Flange yokes 2 x Telma part number TIF01080 / Spicer part number 3-2-429 must be ordered separately.
TL113005
Ford E-350/450 Cutaway Installation Manual with Telma Control Module (TRCM)
Page 4 of 30__________________________________________________________________________17feb12jh
2.2 INSTALL THE CHASSIS BRACKETS
•Remove any bolts such as battery box and/or exhaust hanger mounts or other components that may interfere with
the chassis bracket mounting.
•Clamp the chassis bracket (TIB03127) against the frame rail at dimension X1 from the body mount hole and
dimension T1 from the outside top of the frame. If T1 is 4.5”, the chassis bracket will be against the inside bottom
lip of the frame rail.
•Drill three 9/16” holes in each frame rail using the chassis bracket as a template and secure with bolts (TIF03001),
nuts (TIF03003), and lock washers (TIF03005) included in the kit.
•Tighten the 9/16” bolts to 150 lb-ft (±10%).
•Drill through the chassis bracket any holes needed for battery box and/or exhaust hanger mounts and reinstall the
original bolts and components that were removed previously.
•Refer to the figure below for details.
TL113005
Ford E-350/450 Cutaway Installation Manual with Telma Control Module (TRCM)
Page 5 of 30__________________________________________________________________________17feb12jh
2.3 INSTALL VENT TUBE EXTENSION
•At the time of installation the plastic vent tube extension kit should be attached to the grease chamber vent tube
according to the instructions supplied. Install the vent tube before the retarder bracket is installed to avoid the
possibility of crimping the nylon tube and restricting the outlet. The vent tube is located at the upper passenger
side corner of the Telma. Cut off the vent tube at the bottom of the Telma using a knife or cable cutter. Do not use
diagonal cutters which may crimp and restrict the outlet. Do not wrap the vent tube under the retarder.
TL113005
Ford E-350/450 Cutaway Installation Manual with Telma Control Module (TRCM)
Page 6 of 30__________________________________________________________________________17feb12jh
2.4 ASSEMBLE THE TELMA BRACKETS AND MOUNTS
•Identify the driver’s side of the Telma from the passenger side. To do so, orient the arrow of the red plate on the
Telma towards the axle with the red plate on the driver’s side.
•Identify the Telma brackets. The longer bracket TIB03123 is for the driver’s side. The shorter passenger side
bracket is TIB03124.
•Use four M14 bolts flat washers and Trep washers provided with the set of fasteners (JZ100280) to fasten the
Telma bracket onto each side of the unit. Tighten bolts to 65 lb.-ft (±10%).
•Install the rubber mounts into the retarder brackets. Insert the male parts of the rubber mounts into the 1 5/8” holes
in the brackets from the bottom and the other half of the rubber mount on top. Place one 2 ¾” diameter 5/8” flat
washer on top of each mount.
•Refer to the figure below for details.
2.5 INSTALL THE TELMA IN THE CHASSIS
•Lift the Telma, equipped with its brackets and mounts, into place against the bottom of the chassis brackets.
•Install the M16x1.5x100mm (4”) bolts and spring washers down through the holes in the chassis brackets, mounts
and Telma brackets at each mount. Install a 2 ¾” diameter flat washer, a spring washer and M16 locknut at each
mount and tighten to 150 lb.-ft (±10%).
TL113005
Ford E-350/450 Cutaway Installation Manual with Telma Control Module (TRCM)
Page 7 of 30__________________________________________________________________________17feb12jh
2.6 DRIVE SHAFT MODIFICATION and INSTALLATION
•A slip assembly is required on each side of the Telma. Slip position should be at center of slip travel when shaft is
installed
•Refer to FORD QVM guidelines and SPICER recommendations for proper drive shaft manufacture, balance,
straightness, and critical speed limits.
•Refer to the appendix for Telma guidelines
•Use u-joint SPICER part number SPL36-1X (1410)
•Refer to installation drawings in the appendix for shaft length guidelines
•Shaft lengths over 50” should use 4” tubing
•Always verify proper shaft lengths before modification
•Connect the Telma flange yoke of each drive shaft to the Telma coupling flange.
CN201155: Tighten the 1/2”-20UNF all metal lock nuts to 97-116 lb-ft.
TL113005
Ford E-350/450 Cutaway Installation Manual with Telma Control Module (TRCM)
Page 8 of 30__________________________________________________________________________17feb12jh
2.7 AXLE SHIM INSTALLATION
TL113005
Ford E-350/450 Cutaway Installation Manual with Telma Control Module (TRCM)
Page 9 of 30__________________________________________________________________________17feb12jh
SECTION 3 CONTROL SYSTEM COMPONENTS INSTALLATION
3.1 RELAY BOX MOUNTING
•Install the relay box on the inside driver side frame rail using an existing hole approximately 40” forward from the
center of the Telma and down 1 1/2“ from the top of the frame rail using the relay box mounting brackets TIB01017
x 2 and fasteners supplied in the kit.
•Tighten the four 5/16” bolts to 17 lb-ft (±10%) and the two ½” bolts to 75 lb-ft (±10%).
3.2 LIGHT BAR INSTALLATION
•The Light Bar should be mounted so that it is easily visible to the driver.
•Make a rectangular hole 7/8” wide x 1 ¾” tall in the lower dash to the right of the steering column or install the Light
Bar in an existing console receptacle.
•Install the mating connector onto the five wires (org/wht, blu/wht, yel,grn, brn/wht, blk) found in the relay box
control harness.
•Feed the harness through the hole and connect to the Light Bar
•Plug the light bar into the hole
LIGHT BAR
DISPLAY
PANEL OPENING
TL113005
Ford E-350/450 Cutaway Installation Manual with Telma Control Module (TRCM)
Page 10 of 30__________________________________________________________________________17feb12jh
3.3 TELMA CONTROL MODULE & FOOT CONTROL SWITCH INSTALLATION
Bracket TIB05046 is used to mount the Telma Control Module and foot switch to the dash as shown.
Attach pedal clamp TIB05002 and pedal bracket TIB05047 to the brake pedal using the ¼” bolts, nuts and lock
washers supplied in the kit.
The return spring TIB05021 attaches using the 1/8” holes in the pedal bracket and foot switch bracket.
The special 3/8’ adjustment bolt, nuts and lock washers are assembled as shown.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
