Temple Touch Premium Bedienungsanleitung

Table of

contents:

Safety

warnings

Section

Quick

Start

non-in

asiv

Section

measuring

guidelines

Section

Directions for

use

Section

Room Temperature

Display

Section

Using ODPT

– Medicine

Timer

Section

Setting the operating scale

F or

Section

Installing and replacing the

batteries

Section

About body temperature measurement

Section

Troubleshooting and special indications

Section

10:

Care and

cleaning

Section

11:

Technical

Information

Section

12:

Warranty and Service

Information

IMPORTANT! Read Instructions for Use before using the

thermometer.

Safety

warnings:

1. Keep the thermometer out of the reach of

children.

2. Do not drop the thermometer or expose to heavy shock. The unit is not shock

proof.

3. Do not immerse thermometer in water or any other liquid.

The unit is not water

proof.

4. Do not store the unit in direct sunlight, at a high temperature, in high humidity

dust. Performance of the unit may be

degraded.

5. Stop using the thermometer if it operates erratically or if display

malfunctions.

6. Clean the thermometer probe before storing (see section

10).

7. Do not attempt to disassemble the unit except to replace the

batteries.

QUICK

START

Press and release the POWER

button.

Unit will beep twice when

ready.

Verify temple or underarm mode: Push the SET button if you wish to

change.

Hold firmly to temple or underarm, wait for long beep and read

results.

2. Measuring

guidelines:

1. Measurement body location is the temple, in proximity to the temporal

artery,

between the end of the eyebrow and the

hairline.

2. Do not place the thermometer on scarred tissue compromised by skin disorder, open

sores or abrasions and patients in

trauma.

Temperature readings are affected by many factors including exercise and

drinking

hot or cold beverages prior to taking a

reading.

4. Consult your physician when using drug therapies that may raise the local skin

temperature in the forehead; this may lead to incorrect

reading.

5. Do not place the thermometer on skin exposed to direct sunlight, fireplace heat,

air

conditioner flow and cold/warm compress

therapies.

Wait at least two minute between consecutive measurements for the unit to readjust

to room

temperature.

7. If the thermometer has been stored in a cold temperature, allow the unit to

warm

naturally to room temperature before

using.

8. Performance of the device may be degraded if operated or stored outside stated

temperature and humidity

ranges.

3. Directions for

Use:

Use this thermometer on a clean and dry skin

surface.

Wipe away any perspiration prior to

use.

Taking

Temperature:

1. Press and release the Power button, you will hear one short

beep.

All segments will be displayed (Figure 1) and the backlight will

turn

automatically.

The previous result will be displayed for 2 seconds (Figure

2).

Wait for the hourglass icon to disappear, then two beeps will

heard to indicate that the thermometer is now ready

measure.

Verify that you are in the correct mode: temple or

underarm

(figures 3, 4), if you wish to change. Press and release the SET

button.

Do not try to take a measurement before the two beeps are

heard.

For forehead measurement:

Move hair aside from the temporal area and

apply

the probe to bare skin, in the center of the temple area, between the end of

the

eyebrow and the hairline (Figures 5a + 5b). Gently press and hold to ensure good

contact with the skin is

maintained.

Temple

area 3

For underarm

measurement:

. Place the thermometer probe in the center of the armpit as shown

(figure

6).

Gently press the thermometer's probe in an upward

motion.

. leave the patient's arm raised up until

completed.

Correct placing and good contact with the skin ensure reliable

readouts.

6. As soon as the thermometer is in place, the measurement

will

start automatically. A running circle will appear indicating that

the

measurement is progressing successfully (Figure

7).

Make sure that the thermometer and the patient do not move

while measurement is in

progress.

7. A temperature reading will be displayed within 6-8 seconds. One long beep will

heard to indicate that measurement is complete and temperature will be

displayed

for about 1 minute. The backlight will stay on until the device is shut

down.

8. Press and release the Power button to turn the thermometer off, or it will shut

off

automatically within 1

minute.

If you need to take another reading – wait 2 minutes after turning the

thermometer off and then begin

again.

4. ROOM TEMPERATURE

DISPLAY:

When the thermometer is OFF, continuously press the power

button.

The last body temperature will be displayed, and then will

switch

to the room temperature. (see figure

The room temperature will be displayed unless you press the

power button again and switch off the

thermometer.

5. Using ODPT

– Over Dose Protective

Timer:

The ODPT

timer is designed to track the time elapsed between giving

medicine

dosages to patient and to act as an alert to parents as to when next medicine dosage

should be given (based on time cycle set by

parent).

How to Set & Start

Timer

a. Setting- up the time

cycle:

The ODPT

timer is set for 6 hours by

default.

To change the cycle (from 1-8

hours):

1. Switch OFF the

thermometer.

2. Press and hold the SET

button.

3. Continue pressing the SET button, then press the

timer

button once and release

both

buttons.

The interval time value will blink on the

display.

5. Press the

“Timer”

button to scroll through time interval

options.

The display will show time values between 1-8

hours

(1, 2, 3, 4, 5, 6, 7, 8) and then back to 1 hour (starting over again).

(See figure

9).

6. Release the

“Timer”

button when the desired value appears on the

display.

Then

press the SET button in order to set the desired

value.

b. Operating the

timer:

To start the timer press and release the “Timer” button. The

timer's

display will show "0:00" (See figure 10) . Press again and the timer

will start counting seconds until "0:01" minute and then

minutes.

To reset the timer press and hold the

“Timer” button.

(Press the “Timer” button until display changes to “0:00”).

To start the timer again, press the

“Timer”

button

again.

The count will start

from

“0:00”.

IMPORTANT

NOTES:

•

The ODPT

timer can be used while the thermometer is on or

off.

•

The ODPT

timer continues to count the time elapsed even if the thermometer

turned

off.

•

It is not possible to turn on the timer when conducting temperature

measurement.

Temperatures can be taken while the timer is

running.

•

If the ODPT

timer is stopped mid-cycle, cycle must be reset by pressing and

holding the timer button for 3 seconds. To resume the timer press the

timer

button

again.

•

When the time cycle has ended the thermometer will beep.

The display will

blink

the pre-set time cycle for 60

seconds.

For example, if the timer was set to 6 hours, the image “6:00” will blink on

the

display. 5

6. Setting the operating scale °F or

°C

The device setting is by default Fahrenheit (°F).

To change the scale to °C, or back to

°F:

While OFF, press and hold the SET

button.

Continue pressing SET, then press the POWER

button.

Continue pressing both buttons until the scale changes and then

release.

Wait for 2 beeps and measure temperature (see section

7. Installing and replacing the

Batteries:

The thermometer uses 2 standard AAA 1.5v batteries.

To install/replace, first

switch

off the

device:

Using a screwdriver, loosen the screw on the battery cover and lift it off the

thermometer.

Remove the drained batteries and place new batteries in the battery

compartment,

matching polarity according to the

diagram.

Secure the battery cover using the

screw.

IMPORTANT: It is recommended to remove the batteries from the

thermometer when it is not used for a long

period.

WARNING:

Do not dispose of batteries in fire, recharge, put in

backwards,

disassemble, mix with used or other battery types – they may explode or leak and

cause injury. Waste batteries should be deposit in a batteries recycling trash

only.

About body temperature

measurement:

How does the thermometer

work?

The accurate measurement is obtained

by using a unique probe,

which

measures the heat flow from the

blood

vessels to the skin and converts

to body

temperature.

Information about Body Temperature

What is “normal” body temperature?

Blood

vessels

Energy

Flow

Skin

“Normal” body temperature varies from person to person, changes according to

time

of day and body location. Hot or cold baths, physical exercise, smoking and

drinking,

hot or cold drinks may change body temperature by one degree or

more.

The following table shows the temperature

ranges:

What is

fever?

Average normal temperature

ranges

Forehead

Over

37.8°C/100°F

36.1°C–37.8°C

/ 97.0°F-100.0°F

Rectal*

Over

38°C/100.4°F

36.3°C–38°C

/ 97.3°F-100.4°F

Oral*

Over 37.8°C/100.0°F

36.1°C–37.8°C

/ 97.0°F-100.0°F

Axilla*

(armpit)

Over

37.2°C/99.0°F

35.2°C–37.2°C

/ 95.4°F-99.0°F

*Fever definitions according to the American Medical Association

The thermometer is designed to measure the temperature in the forehead, in

proximity

to the temple area, between the eye socket and the hairline. It is important to

know

that the thermal characteristics of each measurement body location – temporal,

axillar,

oral or rectal

are unique. The variance in temperature measurement in different

body

locations is due to the human body and not the

thermometer.

IMPORTANT: It is recommended to measure the body temperature when

healthy to establish the specific “normal”

temperature

Troubleshooting and special

indications

The thermometer has been designed to display feedback-warnings to ensure proper

usage and accurate temperature

measurement.

When an error appears, the

device

will "beep" 5 times, and then the thermometer will turn off automatically. In the

event

of a malfunction or incorrect temperature measurement, the following warnings will

displayed:

Indication:

The measured temperature is below 95°F (35°C) and the

display presents:

LO.

Instruction:

Turn the unit OFF and then ON

again.

2. Retake temperature using proper placement technique

(see section 3),

while ensuring normal room temperature

(73°F – 77°F / 23°C – 25°C).

3. If still reads LO, this indicates that the patient has a low

body

temperature. 7

Indication:

The measured temperature is above 107.6°F (42°C) and the

display presents:

Instruction:

Turn the unit OFF and then ON

again.

2. Retake temperature using proper technique (see section

3).

3. If still reads HI, this indicates that the patient has a high

fever.

WARNING! A high fever or low body temperature requires seeking

immediate medical

attention

Indication

The thermometer is too cold or too hot to

operate.

Instructions:

Indication

Verify room temperature within product

range 60.8°F-104°F (16°C

40°

2. Retake temperature using proper technique (See section

3).

Temperature did not register because of poor contact, patient

movement or poor

placement.

Instruction:

Turn the unit OFF, wait 2 minutes, turn it ON again and

retake

temperature using proper technique.( See section

3).

Indication

Unit

malfunctioned.

Instruction:

Indication

Do not use the thermometer – contact service. (See section

9).

Low battery

Battery icon is on

continuously.

Instruction:

Indication

The battery has enough remaining life for

approximately

10 more

measurements

Drained battery – only Battery icon is on when thermometer is

turned

on and the device turns itself

OFF.

Instruction:

The battery is drained

replace battery.(See section

10. Care and

Cleaning

* Wipe the tip and probe with an alcohol swab or a cotton swab moistened with

70%

isopropyl alcohol before & after each

use.

After cleaning, wait at least 2 minutes before taking a measurement for the unit

readjust to room

temperature.

Use only a soft dry cloth to clean the body of the thermometer (if necessary). Never

use an abrasive cleanser or submerge the thermometer in water or other

liquids.

Do not expose the thermometer to extreme temperatures, humidity, direct sunlight

shock. Store at room

temperature.

11.

Technical

Specifications

Feature

Performance

/ Data

Measurement

time

6-8

seconds

Measurement

locations

Temple area of the forehead and

underarm

Measurement

range

95°F to 107.6°F (35°C to

42°C)

Operation

vironme

60.8°F-104°F (16°C

40°

Humidity: 15-95% (non condensing)

Storage

environment

-4°F to 122°F (-20°C

50°

C),

Humidity: 15-95% (non condensing)

Measurement

scales

Celsius or

Fahrenheit

Accuracy

Complies with ASTM E 1112-00 standard

requirements

Display

TN LCD 0.78" X 0.77" (20 mm X 19.6

mm)

Batteries

2 AAA 1.5volt

batteries

Battery

life

Minimum 1000 full duty cycles over 24 month

period

Weight

2oz (56gr) including

batteries

Dimensions

3.9" X 2.05" X 1.25" (10x5.2x3.2

cm)

Memory

Last reading display when turned

Auto shut

off

After 60

seconds

Case

material

Food grade ABS

plastic

Probe

material

Food grade Stainless steel,

silicone

12.

Warranty and Service

Information:

All private label Walgreens products have a lifetime guarantee against

manufacturers

defect under normal use. Following the directions closely will ensure years

dependable operation. If the thermometer does not function properly, first check

the

batteries (see section 7). Replace if

necessary.

If the thermometer does not function properly, please write to us

at:

customerservice@medisim-usa.com, or call us at

1-888-723-3659.

Our representatives will provide further instructions on how to correct the trouble or will

ask you to return it for

repair/replacement.

Internally powered

device

* Type

BF Applied

part.

Degree of protection against ingress of water:

Ordinary

Distributed by: Medisim Ltd., G.G Communication Center, Neve ilan 90850

Israel.

Protected by US patent # 6,280,397 B1 and patent application #

11,444,710.

Made in

China

Read the Instructions for Use

Applied part type BF equipment

Inhaltsverzeichnis

Andere Temple Touch Thermometer Handbücher

Temple Touch

Temple Touch Premium Bedienungsanleitung

Beliebte Thermometer Handbücher anderer Marken

Delton

Delton 981A Bedienungsanleitung

Baker

Baker MM2P Bedienungsanleitung

Tarmo

Tarmo 320281 Bedienungsanleitung

Citizen

Citizen CTD 504 Bedienungsanleitung

TFA

TFA 14.1500 Bedienungsanleitung

Vive

Vive DMD1010 Bedienungsanleitung

Gotemp

Gotemp THB4002 Bedienungsanleitung

GREISINGER

GREISINGER G 1202 Bedienungsanleitung

Amprobe

Amprobe TMD-53W Bedienungsanleitung

Trotec

Trotec BP10 Bedienungsanleitung

Radiance instruments

Radiance instruments RT616 Series Bedienungsanleitung

Eurolec

Eurolec IR151 Bedienungsanleitung

Scaneo

Scaneo TS42B Bedienungsanleitung

Sper scientific

Sper scientific 800043 Bedienungsanleitung

Microlife

Microlife NC 200 Bedienungsanleitung

Motorola

Motorola MBP69SN Konfigurationshandbuch

The MeatStick

The MeatStick The MeatStick Bedienungsanleitung

Hama

Hama TH35-A Bedienungsanleitung