Tennant 6100 Schulungshandbuch

IB 340345 (12--02) 1

No. 340345

Machine: 6100

Published: 12--02

Rev. 01

INSTRUCTION BULLETIN

NOTE: DO NOT DISCARD the Parts List from the Instruction Bulletin. Place the Parts

List in the appropriate place in your machine manual for future reference.

Retaining the Parts List will make it easier to reorder individual parts and will

save you the cost of ordering an entire kit.

NOTE: Numbers in parenthesis ( ) are reference numbers for parts listed in Bill of Materials.

Installation instructions for kit number 384436

SYNOPSIS / PROBLEM:

This kit contains the parts needed to install a right hand side brush kit on the model 6100

sweeper.

Please follow step-by-step instructions.

SPECIAL TOOLS / CONSIDERATIONS: NONE

(Estimated time to complete: 2 hours)

PREPARATION:

(Refer to FIG. 1, 2 and 3)

FOR SAFETY: Before leaving or servicing machine, stop on level surface and set parking

brake. Then turn off machine and remove key.

1. Disconnect battery cables from machine.

WARNING: Always disconnect battery cables from machine before working

on electrical components.

2. Remove all hardware mounting the front shroud to the control panel and the machine.

Carefully separate the front shroud from the control panel. Set the front shroud and all

mounting hardware aside.

3. Lift the machine with a hoist or jacks. Block machine properly with jack stands or check that

hoist is properly locked into position.

FOR SAFETY: When servicing machine, block machine tires before jacking up machine.

FOR SAFETY: When servicing machine, jack up machine at designated locations only.

Block machine up with jack stands.

SIDE BRUSH MOTOR GROUP INSTALLATION:

(Refer to FIG. 1, 2 and 3)

1. Mount the electric motor (1) to the side brush bracket (10) with four hex screws (2) and

washers (3).

(Refer to FIG. 1)

2. Mount the right hand side brush guard (15) over the side brush bracket (10) with five hex

screws (2), washers (3) and lock nuts (18).

(Refer to FIG. 1)

3. Press the two flange bearings (6), into the rear end of the side brush mounting channel (5).

(Refer to FIG. 1)

IB 340345 (12--02)2

4. Connect the front end of the side brush mounting channel (5) and the right hand lift

cable (21) to the bracket and motor sub--assembly with the hex screw (7), die spring (11)

and lock nut (9).

(Refer to FIG. 1 and 3)

NOTE: Check that the lift cable (21) is mounted on the left (nut) side of the mounting

channel (5) and the die spring (11) is on the right side of the bracket (10) when

mounted in the channel (5)

(Refer to FIG. 1)

5. Connect the side brush cable (12) to the back side of the side brush bracket (10) with hex

screw (8) and lock nut (9). Tighten the hex screw (8) and lock nut (9) only hand tight, the

side brush cable (12) must be able to move freely.

(Refer to FIG. 1)

6. Place one clevis pin (14) in the side brush channel (5) and the second in the top of the side

brush bracket (10). Connect the two clevis pins (14) with the extension spring (13).

(Refer to FIG. 1)

7. Install the right hand side brush assembly in the machine. Mount the side brush

channel (5) to the frame with one clevis pin (20) and cotter pin (4) and mount the side

brush cable (12) to the frame with the other clevis pin (20) and cotter pin (4).

(Refer to FIG. 1)

8. Secure the side brush wiring harness back along the side brush cable (12) with wire ties.

9. On IC machines only: Secure the main harness with the cable clamp (31) and hex

screw (32).

(Refer to FIG. 2)

SIDE BRUSH LIFT GROUP INSTALLATION:

(Refer to FIG. 1, 2 and 3)

1. Guide the right hand side brush lift cable (21) up through the frame of the machine just

inside the right, front corner brace.

(Refer to FIG. 3)

2. Route the lift cable (21) up over the pulley (22). Secure the cable and pulley to the corner

brace with one hex screw (26), angle piece (25), sleeve (23), and hex nut (27). Tighten

hardware finger tight.

(Refer to FIG. 3)

3. Mount the side brush lift plate (30) to the right side of the side brush support with hex

screw (28), and washer (29). Tighten the hardware finger tight.

(Refer to FIG. 3)

4. Guide the lift cable (21) under the second pulley (22). Secure the lift cable (21) and

pulley (22) to the side brush support with one hex screw (26), angle piece (25), sleeve (24),

and hex nut (27).

(Refer to FIG. 3)

NOTE: Guide the hex screw (26) through the angle piece (25), sleeve (24) and pulley (22).

Continue through the side brush support and side brush lift plate (30). Secure the hex

screw (26) with the hex nut (27) on the back side of the side brush lift plate. (30)

5. Guide the lift cable (21) over the third pulley (22). Secure the cable (21) and pulley (22) to

the top of the side brush support with one hex screw (26), angle piece (25), sleeve (23),

and hex nut (27). Tighten the hardware finger tight.

(Refer to FIG. 3)

6. Connect the end of the lift cable (21) to the side brush lift handle with already existing cable

mounting hardware.

(Refer to FIG. 3)

7. Lower the machine down off the jacks or hoist.

8. Check that the pin (19) is secure in the brush drive shaft.

(Refer to FIG. 1)

9. Mount the side brush sweeping head to the motor with a flat washer (16) and cotter

pin (17).

(Refer to FIG. 1)

IB 340345 (12--02) 3

10. Lower the side brush with the side brush handle. Adjust the side brush height by loosening

and sliding the middle pulley up or down the side brush support. Tighten the pulley when

the side brush is in the preferred operating position.

11. Tighten the other two mounted pulleys with a wrench when the side brush height is

adjusted.

12. Connect the battery cables to the machine. Turn the machine power on, and check the side

brushes for proper operation.

13. Turn the machine power off. Replace the front shroud, and secure with set aside mounting

hardware.

11 12

13 14

FIG. 1 -- SIDE BRUSH MOTOR GROUP INSTALLATION

IB 340345 (12--02)4

31 32

FIG. 2 -- FRONT SHROUD REMOVAL

IB 340345 (12--02) 5

Side brush support

Mount cable with

existing hardware

FIG. 3 -- SIDE BRUSH LIFT GROUP INSTALLATION

IB 340345 (12--02)6

BILL OF MATERIALS FOR RIGHT HAND SIDE BRUSH KIT 384436

TENNANT

Ref. Part No. Description Qty.

1 379213 Motor, Electric, 12V 1

2 15678 Screw, Hex, M06--1.0 X 16, Ss 9

3 01684 Washer, Flat, .25 Ss 9

444906 Pin, Hair Cotter 2

5 81783 Channel, Mtg, Sidebrush 1

6 15648 Bearing, Flange 2

7 06972 Screw, Hex, M12--1.75 X 60, 8.8 1

8 41345 Screw, Hex, M12--1.75 X 25, 8.8 1

908711 Nut, Hex, Lock, M12--1.75,Nl 2

10 81786 Bracket Wldt, Sidebrush 1

11 87242 Spring, Die .50 Id 1.00 Od 1.25 1

12 81784 Cable, Sidebrush 1

13 15047 Spring, Extension 1

14 39019 Pin, Clevis 2

15 81822 Guard,Sidebrush 1

16 04400 Washer, Flat, M16, 17 X30X3Ss 1

17 02942 Pin, Hair Cotter 1

18 08712 Nut, Hex, Lock, M06--1.0, Nl,Ss 5

19 11516 Pin 1

20 06279 Pin, Clevis 2

21 81795 Cable, Sidebrush Lift Rh 1

22 369781 Pulley 3

23 222460 Sleeve 2

24 80395 Sleeve 1

25 54400 Angle 3

26 76570 Screw, Hex, M08--1.25 X 30, 8.8 3

27 08709 Nut, Hex, Lock, M08--1.25,Nl 4

28 06967 Scr Hex M12X1.75 20 1

29 32493 Washer, Flat, .50 Hard 1

30 81955 Plate, Sidebrush Lift 1

31 26395--1 Clamp, Cable, 0.56D 1

32 361339 Screw, Hex 1

TENNANT COMPANY

P. O. Box 1452

Minneapolis, MN 55440-1452

Andere Handbücher für 6100

Inhaltsverzeichnis

Andere Tennant Gebläse Handbücher

Tennant

Tennant 6400 Bedienungsanleitung

Tennant

Tennant 6400 Bedienungsanleitung

Tennant

Tennant sentinel Bedienungsanleitung

Tennant

Tennant 800 Bedienungsanleitung

Tennant

Tennant 285 Bedienungsanleitung

Tennant

Tennant 6600 Bedienungsanleitung

Tennant

Tennant 250 Produkthandbuch

Tennant

Tennant S880 Bedienungsanleitung

Tennant

Tennant CENTURION Bedienungsanleitung

Tennant

Tennant 3620 Bedienungsanleitung

Tennant

Tennant 5700 Schulungshandbuch

Tennant

Tennant SweepSmart S20 ELECTRIC Bedienungs- und Montageanleitung

Tennant

Tennant A60 Bedienungsanleitung

Tennant

Tennant 6550 Bedienungsanleitung

Tennant

Tennant S8 Bedienungsanleitung

Tennant

Tennant S7 Bedienungsanleitung

Tennant

Tennant 810 LPG Bedienungsanleitung

Tennant

Tennant S680 Bedienungsanleitung

Tennant

Tennant 6650 Bedienungsanleitung

Tennant

Tennant S20 Gas Bedienungsanleitung

Tennant

Tennant 800 Bedienungsanleitung

Tennant

Tennant SweepSmart S20 ELECTRIC Bedienungsanleitung

Tennant

Tennant 6200 Bedienungsanleitung

Tennant

Tennant S5 NA Produkthandbuch

Beliebte Gebläse Handbücher anderer Marken

Weed Eater

Weed Eater VS2000BV Bedienungsanleitung

KRAUSMANN

KRAUSMANN U37020-00 Bedienungsanleitung

Bosch

Bosch ALB 36 LI Bedienungsanleitung

Cub Cadet

Cub Cadet HB425 Bedienungsanleitung

GreenWorks Pro

GreenWorks Pro BLB482 Bedienungsanleitung

ARIETE

ARIETE 2768 Bedienungsanleitung

NuTone

NuTone 331H Bedienungsanleitung

GÜDE

GÜDE GLB 200 18 Li-Ion Bedienungsanleitung

I.VA.CO.

I.VA.CO. SC Series Betriebsanleitung

DeWalt

DeWalt DCE100 Bedienungsanleitung

Becker

Becker SV 7.330 Bedienungsanleitung

Metabo

Metabo AG 18 Pro Bedienungsanleitung

Desa

Desa GA3650TB Bedienungsanleitung

Echo

Echo Power Blower PB-230LN Bedienungsanleitung

Echo

Echo PB-413H Bedienungsanleitung

Black & Decker

Black & Decker BV3100 Bedienungsanleitung

Ryobi

Ryobi RY08570 Bedienungsanleitung

Haaga

Haaga 355 Bedienungsanleitung