Teracom TSH330 Bedienungsanleitung

TSH330_R1.2 – May 2022 Page 1

www.teracomsystems.com

TSH330

IP54 Modbus RTU temperature and humidity sensor

Version 1.2 / May 2022

USER MANUAL

Page 2 TSH330_R1.2 – May 2022

1. Short descripon

TSH330 is an IP54 temperature and humidity sensor with an RS-485 interface. It supports the

Modbus RTU protocol.

The temperature and humidity sensor integrates basic elements plus signal processing and

provides a fully calibrated digital output. A unique capacive element is used for measuring relave

humidity while the temperature is measured by a bandgap element. Both elements are seamlessly

coupled to a 12-bit analog to digital converter. This results in superior signal quality.

The digital sensor is mounted in an IP65-rated enclosure. This provides protecon against

dust and water sprays. A cable gland with locknut and screwless terminal block allows easy cable

installaon.

2. Features

• RS-485 interface carrying up to 32 nods;

• LED indicator for status of communication;

• Changeable bitrate and other communication parameters;

• Firmware update via the interface.

3. Applicaons

• Server room and data centers humidity and temperature logging.

• Environmental quality monitoring and assessment.

• Humidity and temperature monitoring in building management systems.

• Humidity and temperature logging for mobile operator facilities, vineyards,

greenhouses, etc.

4. Specicaons

• Physical characteristics

Dimensions: 65.6 x 99 x 36 mm

Weight: 70 g

• Environmental limits

Operating temperature range: -20 to 60°C

Operating relative humidity range: 5 to 95% (non-condensing)

Recommended operating range is 20% to 80% RH (non-condensing) over –10 °C to 60 °C.

Prolonged operation beyond these ranges may result in a shift of sensor reading, with slow recovery time.

It is possible that in some weather condions the moisture in the air in the lter cap may condense. This may result in a

shi of sensor reading, with slow recovery me.

Storage temperature range: -20 to 60°C

Storage relative humidity range: 5 to 95% (non-condensing)

Ingress protection: IP54

• Power requirements

Input Voltage (including -15/+20% according to IEC 62368-1): 4.5 to 26 VDC

Input Current: 5 mA@5VDC

• Humidity measurements

Accuracy (min): ±3.0 %RH (in 20 to 80 %RH range)

Accuracy (max): ±5.0 %RH (in 5 to 95 %RH range)

Resolution: 0.1 %RH

• Temperature measurements

Accuracy (min): ±0.4 °C (in -10 to +60°C range)

Accuracy (max): ±0.6 °C (in -20 to +60°C range)

Resolution: 0.1 °C

• Warranty

Warranty period: 3 years

TSH330_R1.2 – May 2022 Page 3

5. Pinout

Pin Descripon Corresponding

UTP wires color

Line B- RS485 Blue

Line A+ RS485 Blue/White Tracer

GND Ground (negave) supply Brown

+4.5÷26V Posive power supply Brown/White Tracer

6. Installaon

The device is designed for wall mounng using screws passing through the sloed holes in

the enclosure.

A daisy-chained (linear) topology for mulple sensors should be used. UTP/FTP cables are

mandatory for interconnecon. The last sensor in the chain should have a terminator of 120ohm

installed on the bus. TSH330 has a built-in terminator. To enable it, please close the jumper.

7. Installaon ps

The locaon and the mounng posion of sensors have a direct eect on the accuracy

of measurements. The ps below will ensure good measuring results:

• Sensor shall be installed about 1.2-1.4 m above the floor;

• Avoid exposure to direct sunlight - solar radiation causes measurement inaccuracy;

• For outdoor usage, the sensors should be installed with protection from direct rain;

• Avoid mounting over ventilation shafts and windows/doors;

• Avoid attaching to walls in front of a chimney.

• It is recommended to mount the device in an accessible location for easier

maintenance.

Aenon:

The device should be installed with always lter and gland facing the oor.

8. Status indicator

The status of the device is shown by a single LED, located on the front panel:

• If the LED blinks for a period of 1 second, the sensor works properly;

• If the LED blinks for a period of 3 seconds, there isn‘t communication with the

controller;

• If LED doesn‘t blink, there isn‘t a power supply.

Page 4 TSH330_R1.2 – May 2022

9. Factory default sengs

Disconnect the sensor from the bus (switch o the power supply).

Press and hold the “cong” buon. Don’t release the buon, connecng the sensor to the bus

(switch on the power supply).

The “status” LED will be ON for 3 seconds and aer this will ash for 7 seconds. Aer the 10-th

second the LED will be ON.

Release the buon. The sensor will restart with factory default sengs.

10. Firmware update

The rmware of the sensor can be updated with a Teracom controller which supports

MODBUS RTU or MBRTU-Cong soware. For more details ask your dealer.

11. Modbus address table

PDU

Address

(Decimal)

Logical

address

(Decimal)

Oset

(Decimal) Data size Default Valid values

RS-485 address R/W 03/06 10 40011 40001 16-bit uns. integer 1 1-247

Baud rate * R/W 03/06 11 40012 40001 16-bit uns. integer 19200 2400, 4800, 9600, 19200,

38400, 57600

Parity, data, stop bits * R/W 03/06 12 40013 40001 16-bit uns. integer 1 1=E81, 2=O81, 3=N81

Data order R/W 03/06 13 40014 40001 16-bit uns. integer 1 1=MSWF (MSW, LSW)

2=LSWF (LSW, MSW)

Sub-family number R 3 14 40015 40001 16-bit uns. integer 0xCD

FW version R 3 15 40016 40001 16-bit uns. integer

Vendor URL R 3 18 40019 40001 64 bytes UTF-8 teracomsystems.com

Float test value (MSWF) R 3 82 40083 40001 32-bit oat -9.9(0xC11E6666)

Float test value (LSWF) R 3 84 40085 40001 32-bit oat -9.9(0xC11E6666)

Signed integer test value R 3 86 40087 40001 16-bit sig. integer -999(0xFC19)

Signed integer test value (MSWF) R 3 87 40088 40001 32-bit sig. integer -99999(0xFFFE7961)

Signed integer test value (LSWF) R 3 89 40090 40001 32-bit sig. integer -99999(0xFFFE7961)

Unsigned integer test value R 3 91 40092 40001 16-bit uns. integer 999(0x03E7)

Unsigned integer test value (MSWF) R 3 92 40093 40001 32-bit uns. integer 99999(0x0001869F)

Unsigned integer test value (LSWF) R 3 94 40095 40001 32-bit uns. integer 99999(0x0001869F)

Temperature °C R 3 100 40101 40001 32-bit oat

Humidity %RH R 3 102 40103 40001 32-bit oat

Dew point °C R 3 104 40105 40001 32-bit oat

Temperature °F R 3 200 40201 40001 32-bit oat

Humidity %RH R 3 202 40203 40001 32-bit oat

Dew point °F R 3 204 40205 40001 32-bit oat

Temperature °C x 100 R 3 400 40401 40001 16-bit sig. integer

Humidity %RH x 100 R 3 401 40402 40001 16-bit sig. integer

Dew point °C x 100 R 3 402 40403 40001 16-bit sig. integer

Temperature °F x 100 R 3 500 40501 40001 16-bit sig. integer

Humidity %RH x 100 R 3 501 40502 40001 16-bit sig. integer

Dew point °F x 100 R 3 502 40503 40001 16-bit sig. integer

MSWF - Most signicant word rst - (bits 31 … 16), (bits 15 … 0); LSWF - Least signicant word rst - (bits 15 … 0), (bits 31 … 16);

PDU address - Actual address bytes used in a Modbus Protocol Data unit

A “NaN” value is returned for unavailable oang-point values (e.g. in case of measurement error)

* The sengs will take eect aer restarng the sensor by a power-on reset.

12. Recycling

Recycle all applicable material.

Do not dispose of in the regular household refuse.

Andere Teracom Temperaturregler Handbücher

Teracom

Teracom TSM400-4-TH Bedienungsanleitung

Beliebte Temperaturregler Handbücher anderer Marken

Swegon

Swegon LUNAd MB Bedienungsanleitung

Lucky Reptile

Lucky Reptile Thermo Control II Bedienungsanleitung

SENSORMETRIX

SENSORMETRIX Argon 100 Bedienungsanleitung

Fuji Electric

Fuji Electric PXE4 Bedienungsanleitung

Yuyao gongyi

Yuyao gongyi XMT-808 series Bedienungsanleitung

Selec

Selec TC544C Bedienungsanleitung

P.W. KEY

P.W. KEY rt-208gt Bedienungsanleitung

Future Design

Future Design FDC-9200 Bedienungsanleitung

BH Thermal

BH Thermal BriskONE Bedienungsanleitung

Omron

Omron E5EX-H Bedienungsanleitung

West Control Solutions

West Control Solutions KS 45 Kurzanleitung

MCS

MCS RITC-15B Bedienungsanleitung

SMC Networks

SMC Networks Thermo-con INR-244-639 Bedienungsanleitung

eltherm

eltherm Ex-TC It Series Bedienungsanleitung

Omron

Omron C200H-TV Series Bedienungsanleitung

industrie technik

industrie technik CA1 Bedienungsanleitung

KRAL

KRAL EET 32 Bedienungsanleitung

dixell

dixell XR420C Verdrahtungsschema