Terex GS32MT-101 Bedienungsanleitung
Operator's Manual
Serial Number Range
GS™-1432m
from GS32MD-101
from GS32MP-
101
from GS32MT-101
ANSI/CSA
Hong Kong
GS™-1932m
GS™-1932m Lite
with
Maintenance
Information
Original Instructions
First Edition
Third Printing
Part No. 1308591GT
Operator's Manual First Edition • Third Printing
GS™-1432m • GS™-1932m • GS™-1932m Lite Part No. 1308591GT
FrontMatter
Contents
Introduction ............................................................1
Symbol and Hazard Pictorials Definitions..............5
General Safety .......................................................8
Personal Safety................................................... 14
Work Area Safety................................................ 15
Legend ................................................................ 22
Controls............................................................... 23
Inspections.......................................................... 26
Operating Instructions......................................... 41
Transport and Lifting Instructions ....................... 55
Maintenance ....................................................... 60
Specifications...................................................... 62
Copyright © 2020 Terex Corporation
First Edition: Third Printing, April 2023
Genie is a registered trademark of Terex South Dakota, Inc. in
the U.S.A. and many other countries. “GS” is a trademark of
Terex South Dakota, Inc.
These machines comply with
ANSI/SAIA A92.20
CAN/CSA B354.6
First Edition • Third Printing Operator's Manual
Introduction
Part No. 1308591GT GS™-1432m • GS™-1932m • GS™-1932m Lite 1
Intr od ucti o n
About this manual
Genie appreciates your choice of our machine for
your application. Our number one priority is user
safety, which is best achieved by our joint efforts.
This book is an operation and daily maintenance
manual for the user or operator of a Genie
machine.
This manual should be considered a permanent
part of your machine and should remain with the
machine at all times. If you have any questions,
contact Genie.
Product Identification
The machine serial number is located on the serial
label.
Serial label located in
charger tray
Serial number stamped on
chassis
Intended Use and Familiarization
Guide
The intended use of this machine is to lift
personnel, including tools, and materials to an
aerial work site. Before operating the machine, it’s
the operator’s responsibility to read and
understand this familiarization guide.
Each person must be trained to operate a
Mobile Elevating Work Platform (MEWP).
Familiarization with the MEWP must be given
to each person who is authorized, competent
and trained.
Only trained and authorized personnel should
be permitted to operate the machine.
The operator is responsible to read,
understand, and obey the manufacturer’s
instructions and safety rules provided in the
Operator’s Manual.
The Operator’s Manual is located in the
manual storage container, at the platform.
For specific product applications, see
Contacting The Manufacturer.
Operator's Manual First Edition • Third Printing
Introduction
2 GS™-1432m • GS™-1932m • GS™-1932m Lite Part No. 1308591GT
Platform controls symbology and related
machine movement:
Lift function enable button
Drive function enable button
Platform up/down (when lift function
selected)
Drive forward/reverse (when drive
function selected)
Steer right/left (when drive function
selected)
Area of operation, indoor use button
Area of operation, outdoor us
e button
Ground controls symbology and related
machine movement:
Lift function enable button
Platform up/down button
Sequential functions and movement:
•Drive and steer.
Interlocked functions:
•Elevated drive speed.
•Elevated drive in an off-level condition.
•All platform and ground controls.
Limitations of use:
•The intended use of this machine is to lift
personnel, including tools, and materials to an
aerial work site.
•Do not elevate the platform unless the machine
is on firm level ground.
First Edition • Third Printing Operator's Manual
Introduction
Part No. 1308591GT GS™-1432m • GS™-1932m • GS™-1932m Lite 3
Bulletin Distribution and Compliance
Safety of product users is of paramount
importance to Genie. Various bulletins are used by
Genie to communicate important safety and
product information to dealers and machine
owners.
The information contained in the bulletins is tied to
specific machines using the machine model and
serial number.
Distribution of bulletins is based on the most
current owner on record along with their
associated dealer, so it is important to register
your machine and keep your contact information
up to date.
To ensure safety of personnel and the reliable
continued operation of your machine, be sure to
comply with the action indicated in a respective
bulletin.
To view any open bulletins for your machine, visit
us on the web at www.genielift.com.
Contacting the Manufacturer
At times it may be necessary to contact Genie.
When you do, be ready to supply the model
number and serial number of your machine, along
with your name and contact information. At
minimum, Genie should be contacted for:
Accident reporting
Questions regarding product applications and
safety
Standards and regulatory compliance information
Current owner updates, such as changes in
machine ownership or changes in your contact
information. See Transfer of Ownership, below.
Transfer of Machine Ownership
Taking a few minutes to update owner information
will ensure that you receive important safety,
maintenance and operating information that
applies to your machine.
Please register your machine by visiting us on the
web at www.genielift.com or by calling us toll free
at 1-800-536-1800.
Operator's Manual First Edition • Third Printing
Introduction
4 GS™-1432m • GS™-1932m • GS™-1932m Lite Part No. 1308591GT
Danger
Failure to obey the instructions and
safety rules in this manual will result
in death or serious injury.
Do Not Operate Unless:
You learn and practice the principles of safe
machine operation contained in this operator’s
manual.
1 Avoid hazardous situations.
Know and understand the safety rules
before going on to the next section.
2 Always perform a pre-operation inspection.
3 Always perform function tests prior to use.
4 Inspect the workplace.
5 Only use the machine as it was intended.
You read, understand and obey the
manufacturer’s instructions and safety rules—
safety and operator’s manuals and machine
decals.
You read, understand and obey employer’s
safety rules and worksite regulations.
You read, understand and obey all applicable
governmental regulations.
You are properly trained to safely operate the
machine.
Safety Sign Maintenance
Replace any missing or damaged safety signs.
Keep operator safety in mind at all times. Use mild
soap and water to clean safety signs. Do not use
solvent-based cleaners because they may
damage the safety sign material.
Hazard Classification
Decals on this machine use symbols, color coding,
and signal words to identify the following:
Safety alert symbol
—
used to alert
you to potential personal injury
hazards. Obey all safe
ty
messages that follow this symbol
to avoid possible injury or death.
Indicates a hazardous situation
which, if not avoided, will result in
death or serious injury.
Indicates a hazardous situation
which, if not avoided, could result
in death or
serious injury.
Indicates a hazardous situation
which, if not avoided, could result
in minor or moderate injury.
Indicates a property damage
message.
First Edition • Third Printing Operator's Manual
Symbol and Hazard Pictorials Definitions
Part No. 1308591GT GS™-1432m • GS™-1932m • GS™-1932m Lite 5
Symb ol and H az ar d Pict or i als De fi ni ti ons
Read the operator’s
manual
Read the service
manual
Crush hazard Crush hazard Collision hazard
Tip-over hazard Tip-over hazard Tip-over hazard Tip-over hazard Electrocution hazard
Electrocution hazard Explosion hazard Fire hazard Burn hazard Skin injection hazard
Operator's Manual First Edition • Third Printing
Symbol and Hazard Pictorials Definitions
6 GS™-1432m • GS™-1932m • GS™-1932m Lite Part No. 1308591GT
Engage safety arm Keep away from
moving parts
Keep clear of tires Move machine to
level ground
Close chassis tray
Lower the platform. Platform overloaded Maintain required
clearance
Access by trained
and authorized
personnel only
Use a piece of
cardboard or paper
to search for leaks
Batteries used as
counterweights
Chock the wheels No smoking Grounded AC
3-wire only
Replace damaged
wires and cords
First Edition • Third Printing Operator's Manual
Symbol and Hazard Pictorials Definitions
Part No. 1308591GT GS™-1432m • GS™-1932m • GS™-1932m Lite 7
Wheel load Lifting and tie down
instructions
Lifting point Lanyard anchorage
points
Wind speed
Tiedown Release brakes Engage brake Pressure rating for air
line to platform
Voltage rating for
power to platform
Maximum capacity Indoor Outdoor Manual force
Auxiliary lowering
Operator's Manual First Edition • Third Printing
General Safety
8 GS™-1432m • GS™-1932m • GS™-1932m Lite Part No. 1308591GT
Gener al Saf et y
Dieses Handbuch passt für folgende Modelle
5
Inhaltsverzeichnis
Andere Terex Hebesystem Handbücher
Terex
Terex Genie Superlift Advantage Bedienungsanleitung
Terex
Terex Genie GS -1530/32 Bedienungsanleitung
Terex
Terex Genie IWP Series Bedienungsanleitung
Terex
Terex Genie S-100 Bedienungsanleitung
Terex
Terex Genie QS-12W Bedienungsanleitung
Terex
Terex SX180H-745 Bedienungsanleitung
Terex
Terex Genie AWP Series Bedienungsanleitung
Terex
Terex Genie GS-1432m Bedienungsanleitung
Terex
Terex Genie Lift Guard S-60 Bedienungsanleitung
Terex
Terex SX135D-101 Bedienungsanleitung
Terex
Terex Genie Z-45/25 Bi-Energy Bedienungsanleitung
Terex
Terex Genie GS-1532 Installations- und Betriebsanleitung
Terex
Terex Genie GS-1530 Bedienungsanleitung
Terex
Terex Genie SX-150 Installations- und Betriebsanleitung
Terex
Terex Genie GTH4016 SR Bedienungsanleitung
Terex
Terex Genie Z-34/22 IC Bedienungsanleitung
Terex
Terex GS90D-4695 Installations- und Betriebsanleitung
Terex
Terex Genie GTH1215M-101 Installations- und Betriebsanleitung
Terex
Terex Genie S-80 XC Series Bedienungsanleitung
Terex
Terex Genie GS-1432m Installations- und Betriebsanleitung
Beliebte Hebesystem Handbücher anderer Marken
morse
morse 82H-124 Bedienungsanleitung
Braun
Braun NL955 Series Bedienungsanleitung
haacon
haacon 1889.10 Bedienungsanleitung
Protekt
Protekt AT 252 Bedienungsanleitung
R. Beck Maschinenbau
R. Beck Maschinenbau HS 600 Bedienungsanleitung
Nova Technology International, LLC
Nova Technology International, LLC NAS Series Bedienungsanleitung
Genie
Genie Z-60/34 Bedienungsanleitung
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Bedienungsanleitung
Custom Equipment
Custom Equipment Hy-Brid 3 Series Programmierhandbuch
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Programmierhandbuch
