Tesoro Sand Shark Montageanleitung

SAND SHARK OPERATOR INSTRUCTION MANUAL

CONGRATULATIONS!

Your new TESORO metal detector was designed to provide you with many happy hours of

enjoyment in the most rewarding hobby I can think of—treasure hunting. Ahead of you lie

fascinating and exciting experiences as you step into the past, uncovering artifacts lost by past

generations. I wish we could share these experiences with you, and we wish you the best of

success.

Your Tesoro metal detector is capable of meeting your needs in a wide range of treasure hunting

situations. As with any detector, operator skill and familiarity is probably the limiting factor in

determining how successful you will be. We recommend that you read and understand this

manual fully before attempting to use the instrument in the field. Then, as you practice and

become familiar with your detector, your rate of success will increase dramatically.

Your TESORO metal detector is a precision electronic instrument, which will last for years if

properly cared for. Treat it right and it won’t let you down.

Good Hunting! Jack Gifford

GENERAL DESCRIPTION

The Sand Shark is the first Pulse Induction metal detector that is controlled by microprocessor

technology. It combines new technology with Tesoro's time-proven PI circuits and

interchangeable Spiral Printed coils. While simple to operate, the Sand Shark offers a wide

variety of user definable controls that allow for precise fine-tuning of the detector. Don’t be

fooled by its simplicity, the Sand Shark is capable of delivering peak performance by eliminating

troublesome adjustments and complicated features creating an extremely simple to operate

lightweight detector. The Sand Shark is packaged in a waterproof housing making it ideal for wet

weather use, beach hunting, or diving in fresh or salt water. It is convertible to body/belt mount

and requires no special tools.

As a Pulse Induction instrument the Sand Shark will provide mineral free operation in virtually

all ground mineral or salt water environments. Equipped with auto tuning the Sand Shark is a

motion- based "all metal" detector. Though the searchcoil must be moving when pinpointing,

due to the auto tuning, the amount of motion is so slight that pinpointing is easily accomplished.

Designed as an all-purpose detector, the Sand Shark requires no special ground adjustments or

complicated set-up. A variety of optional searchcoils provide the operator greater versatility and

a wider range of site selection. A guide to selecting the proper optional coil is included in the

section for "Selecting the Right Searchcoil."

Be sure to complete and mail the warranty registration card in order to validate your

warranty.

UNPACKING THE BOX

Your Sand Shark was shipped with these parts:

1 Upper Pole Assembly

Fully assembled, including upper pole stem with handle grip, padded arm bracket, pole lock and

control housing.

1 Middle Pole Assembly With Pole Lock

1 Lower Pole Assembly

Fully assembled with 2 washers and nylon nut and bolt.

1 8” round printed spiral searchcoil with 8' cable

1 8-cell battery pack with 8 AA batteries installed

1 Tube of Dow Corning #4 silicone

2 Velcro cable straps

1 Operator Instruction Manual

1 Tesoro Warranty Card

If any of these items are missing, contact the Tesoro Authorized Dealer where you purchased

your detector immediately.

ASSEMBLING YOUR DETECTOR

1. On the lower pole assembly, remove the mounting

screw and thumb nut from the pole tip.

2. Insert the pole tip between the mounting ears of the

searchcoil and align the holes of the pole tip and

washers with those of the mounting ears.

Note: The pole tip should fit very snugly into the

mounting ears.

3. Insert the mounting screw through the holes in the

mounting ears and pole tip—entering from the side

opposite the cable connection.

4. Install the thumb nut on the mounting screw and

tighten by hand.

Note: Do not overtighten the thumb nut. It should be snug but not too difficult to loosen

up.

5. On the middle pole assembly, depress the two spring buttons and slide the middle pole

assembly into the upper pole assembly until the spring buttons click into the holes—

locking the two assemblies into place. Tighten the pole lock to secure the two assemblies

together.

6. Slide lower pole into middle pole until spring buttons click into the first set of adjustment

holes. Turn pole lock to tighten—locking the assembly into place.

7. The Sand Shark can be assembled in several different configurations. Take a look at the

pictures below to find out the best configuration for you:

Control housing mounted under arm

Control housing mounted under pole

Divers setup (lower pole set directly into upper pole)

Body Mount

Converting the Sand Shark from pole mount to body/belt mount is simply a matter of

removing the control box from the upper pole and unwinding the cable. To remove the

control box from the pole, depress the four spring buttons that hold the mounting bracket

and control box to the pole, and lift. It is easiest to release one set of spring buttons at a

time.

8. Once you have decided on a pole mount configuration, wrap the cable around the pole

leaving enough slack near the searchcoil to permit searchcoil adjustment.

Install the coil connector into its receptacle on the back of the control housing and

tighten it fingertight.

Note: Do not use pliers to tighten the coil connector. Do not allow the cable to flop loosely over

the searchcoil. Since the detector is sensitive enough to “see” the tiny wires in the cable, a

floppy cable can cause false signals as the searchcoil senses the moving wires.

BATTERY INSTALLATION / REPLACEMENT

The Sand Shark has been equipped with a drop-in battery pack. To install or replace the batteries,

make sure the detector housing is dry, then release the two draw bolts securing the faceplate to

the housing. Gently pull the control panel free being careful not to twist or strain the ribbon cable

connecting the faceplate panel to the printed circuit board. The Sand Shark takes 8 AA size

alkaline batteries. Also, make certain that you follow the polarity indicators on both the battery

holder as well as the batteries themselves. Then check the polarity of the pack as it goes into the

housing. Look inside the housing for the two spring clips and slide the pack so that the battery

terminals meet the spring clips. There is only one correct way to put the battery pack in. If the

batteries are put in wrong, the detector will not work. Replace the faceplate and use the

drawbolts to clamp the faceplate back onto the housing.

Do not rest the unit on the coil connector while clamping the faceplate. This can cause excess

wear and damage to the connector.

IMPORTANT NOTE: Always make sure the instrument is dry before opening. Water, if

allowed to make contact with the circuit board, may damage it. Always make sure the O-

ring is clean and free of dirt or sand. It is recommended that you wipe the O-ring with a

dry cloth and look for damage and apply a new coat of diver's silicone grease before

replacing it. Failure to maintain the O-ring will result in extensive damage and will not be

covered under warranty.

ADJUSTMENT

The searchcoil angle and stem length should be adjusted so that the unit

does not become uncomfortable or tiring to hold after long periods of

use. The detector should rest in your hand with arm relaxed allowing it

to swing back and forth without having to lift with the elbow or

shoulder while keeping the searchcoil as close as possible to the ground

without touching. The pole length is adjusted by depressing the spring

buttons and extending or shortening the lower stem until they click into

the set of holes that give you the most comfortable setting. The

searchcoil should rest about one inch above the ground while standing

erect. Adjust the angle of the searchcoil so that it is parallel to the

ground. Tighten the searchcoil thumbnut by hand so that the searchcoil

will maintain this setting.

QUICKSTART TEST AND TUNING PROCEDURES

The Quickstart is designed to teach you how to use your new Sand Shark. It provides a quick and

easy means of learning all of the functions of your detector and the concepts behind the

functions.

You will need the following items:

1. Your fully assembled Sand Shark metal detector.

2. Several targets for air test.

3. A nonmetal table or counter surface.

Here’s what you will do:

1. Set the THRESHOLD and VOLUME.

2. Perform an Audio Battery Test.

3. Perform an Air Test in the VCO Mode.

4. Set the Audio Frequency for the NORMAL Mode.

5. Perform an Air Test in the NORMAL Mode.

6. Set the Pulse Width.

Prepare for the Quickstart

Place your assembled Sand Shark on the nonmetal surface as shown in the photo. Make sure

there are no metal objects near the coil and remove any jewelry from your hands and wrists.

Start with the controls like this:

1. PULSE WIDTH in center position.

2. VOLUME & THRESHOLD in the 1 o’clock position.

3. Mode Switch in OFF position.

Set the Threshold and Volume

The Mode Switch controls all of the tuning functions on your Sand Shark. As we go through the

other tuning steps, we will be resetting the Mode switch to the other functions.

We will start by turning the Mode Switch from off to VCO. At this time you will hear a

humming tone in the headphones. This sound is the threshold. Its purpose is to give you a

reference point to judge targets by. Some targets may be small enough or deep enough that they

will not be able to generate an audio tone by themselves. By monitoring a threshold, you already

have a signal so changes in that signal are easier to hear. However if the threshold is set too loud,

the small changes will not be noticed. Therefore, a low steady threshold setting is ideal. You can

change the threshold with the Threshold adjust knob. Try turning it up and down to find the best

possible setting for the machine.

Once the threshold has been set, you should adjust the volume control to a comfortable level.

Please remember that the sound level will be affected by your surroundings. What may be just

right in one location may be too high or low in another. The volume can be changed with the

VOLUME adjust knob. Take a moment and find the level that is best for you now.

Perform an Audio Battery Test

With the threshold and volume set, we will now check the batteries. Turn the THRESHOLD

adjust knob all the way counterclockwise until you feel a click. You should hear a number of

beeps. If the batteries are fully charged, you will hear 6 or 7 beeps. As the batteries drain, you

will hear fewer and fewer beeps. When you hear no beeps or only one, it will be time to replace

your batteries. Please remember that you will have to reset your threshold when you are done

with the battery test. Try your battery test and reset your threshold before moving to the next

step.

Perform an Air Test in the VCO mode

You are now ready to perform an air test in the VCO Mode. VCO stands for Voltage Controlled

Oscillator. The VCO mode has a very distinct sound that makes it very easy to work with. As a

target gets close to the coil, the rise in signal voltage causes the oscillator to change frequency

and amplitude causing the audio part of the signal to become higher in pitch and louder in

volume. These changes will leave no doubt in your mind that you are close to a target. Try

waving your targets in front of the coil. Start from a distance of 10 to 12 inches away from the

coil and work your way towards the coil. Now try starting from 6 inches to the left or right side

of the coil and working your way to the center of the coil. Notice how the audio signal changes.

Your strongest signal will always be closest to the center of the coil, but additional information

can also be learned by the signal strength. A deep or small target will give a smaller change in

the threshold than a larger or shallower target will give. Take some time to try a number of

different targets at different depths to find out how your detector sounds.

Set the Audio Frequency for the Normal Mode

In the NORMAL tuning mode you will be able to preset the frequency of the audio tone that you

will hear in the headphones. The adjustment is made by going into the “F” SET Mode on the

Mode switch. Notice that the “F” SET is highlighted in this mode and that “F” ADJUST written

in the same highlighting is found beneath the THRESHOLD adjust knob. When the mode switch

is in “F” SET, the THRESHOLD adjust knob now sets the audio tone. Try turning the “F”

ADJUST knob up and down to find the audio frequency that you like best. While you are in the

“F” SET mode, your Sand Shark will not respond to targets. When you are ready, turn the Mode

switch to NORMAL. Please remember that once the frequency is set, you must reset your

threshold to a low steady hum.

Perform an Air Test in the Normal Mode

You are now operating in the NORMAL Mode. In this mode only, one frequency at a time will

be heard and the volume of the audio signal will determine signal strength. Try waving your

targets in front of the coil. Start from a distance of 10 to 12 inches away from the coil and work

your way towards the coil. Now try starting from 6 inches to the left or right side of the coil and

working your way to the center of the coil. Notice the difference from what you heard in the air

test in the VCO Mode. Your strongest signal is still closest to the center of the coil, but there was

no change in audio frequency. Take some time to try a number of different targets at different

depths to find out how your detector sounds.

Set the Pulse Width

The PULSE WIDTH setting controls the amount of signal that the Sand Shark will transmit into

the ground. A pulse induction detector works by transmitting a signal and then reading the

residual eddy currents that are left on metal items. All of this takes place at approximately 600

pulses per second. Increasing the pulse width allows the detector to transmit longer and create

more eddy currents on a metal target. These extra currents are more easily picked up during the

receive phase and will therefore increase depth and sensitivity. However, more transmitted signal

means more power used in the transmit phase, limiting the battery life. We have marked the best

balance of battery life and depth and sensitivity on the faceplate at the mid-position on the

PULSE WIDTH adjust knob. You will be able to increase or decease the PULSE WIDTH by

turning the Pulse width adjust knob. Start with the detector in the factory recommended position

and wave a few targets in front of the coil. Try turning the knob and see what effects it has on

depth and sensitivity.

CONGRATULATIONS

You have completed the Sand Shark Quickstart Test and Tuning Procedures and in the process

have learned quite a lot about your new Sand Shark. But experience is the best teacher. I would

recommend that you get out and practice with your detector as much as possible. For your

convenience, you may want to create a test garden in your lawn or work a local park. Any time

spent using your detector will give you valuable experience.

SELECTING THE RIGHT SEARCHCOIL

Selecting the right searchcoil for the type of detecting you’re doing will add greatly to your

success. The Sand Shark comes with a standard 8 inch Printed Spiral coil, which is a new and

revolutionary design developed by Tesoro specifically for the Sand Shark. This is an excellent

overall coil since most people who operate PI instruments are usually searching large sandy

beach areas where targets are easy to dig and there is usually not an over abundance of trash.

This coil will detect very tiny targets for its size and provides excellent target separation while

giving more ground coverage. However, it is not always the right coil for the job. Therefore,

Tesoro has made it possible to interchange coils and has developed a variety of its unique Printed

Spiral searchcoil in a selection of sizes.

In addition to the standard 8 inch open center searchcoil, three optional coil sizes are available

for the Sand Shark. The 10 1/2 inch open center coil is designed for areas where digging is easier

and where junk targets may not be too numerous. The 7 inch coil will be particularly useful when

searching for smaller targets, such as gold nuggets. The 10 inch elliptical allows a widescan

sweep pattern while keeping a good sensitivity to small targets.

PINPOINTING

Move the searchcoil slowly across the target from side to side and then from front to back at 90

degree angles. Raise the coil slightly, slow the sweep speed, and shorten the sweep to narrow the

detection area enough to make it easy to tell where the coil center is at the instant of sound as

you crisscross the target.

DETECTOR PROTECTION CHECKLIST

Congratulations, you have just purchased a new metal detector, and we wish to thank you for

choosing Tesoro.

So many people are disappointed when their new "state-of-the-art" detector becomes less and

less exciting to use and doesn't seem to go as deep anymore. There is something that you can do

to keep your new detector working as good as when it was new.

The most important thing is simply to remember that your detector is an electronic instrument

and to treat it as such. You wouldn't expect your TV set to operate properly if you stored it in the

trunk of your car, would you?

We have generated the following list to help you take care of your detector and to help ensure

that you do not void its warranty. If you will follow its guidelines, you will find your detector

will not let you down.

1. Operate your detector exactly as recommended in this Operator Instruction Manual.

2. Do not attempt to modify or repair the detector's electronics.

3. Cable is hard-wired into searchcoil. Do not attempt removal of the spring retainer on the

searchcoil housing.

4. Use only high quality carbon-zinc, alkaline, or nicad batteries. Remove batteries during

long term storage. Never substitute batteries of other voltages. Brands should not be

mixed. Do not attempt to modify the power supply system.

5. Never spray lubricants such as WD-40 or any types of cleaners, sealants or other

chemical preparation on or into the detector.

6. Avoid banging the searchcoil against rocks or foundation walls.

7. Always protect the searchcoil with a properly designed scuff cover.

Inhaltsverzeichnis

Andere Tesoro Metalldetektor Handbücher

Tesoro

Tesoro Deep Search VII Montageanleitung

Tesoro

Tesoro Toltec 100 Montageanleitung

Tesoro

Tesoro Compadre Montageanleitung

Tesoro

Tesoro Mayan Bedienungsanleitung

Tesoro

Tesoro Cibola Bedienungsanleitung

Tesoro

Tesoro Cibola Montageanleitung

Tesoro

Tesoro LOBO Montageanleitung

Tesoro

Tesoro Bandido Montageanleitung

Tesoro

Tesoro Aztec Montageanleitung

Tesoro

Tesoro Inca Montageanleitung

Tesoro

Tesoro Golden uMax Montageanleitung

Tesoro

Tesoro PIranha Montageanleitung

Tesoro

Tesoro mMAX BANDIDO Montageanleitung

Tesoro

Tesoro Stingray II Montageanleitung

Tesoro

Tesoro Outlaw Montageanleitung

Tesoro

Tesoro Bandido II Montageanleitung

Tesoro

Tesoro Silver Sabre UMAX Montageanleitung

Tesoro

Tesoro COMPADRE Montageanleitung

Tesoro

Tesoro Deep Search VI Montageanleitung

Tesoro

Tesoro Mojave Montageanleitung

Tesoro

Tesoro Amigo II Montageanleitung

Tesoro

Tesoro TIGER SHARK Montageanleitung

Tesoro

Tesoro De Leon Montageanleitung

Tesoro

Tesoro VAQUERO Montageanleitung

Beliebte Metalldetektor Handbücher anderer Marken

Garrett

Garrett MAGNASCANNER CS 5000 Bedienungsanleitung

Valex

Valex 1800200 Bedienungsanleitung

Gauss

Gauss MIL MD Bedienungsanleitung

Velleman

Velleman CS130 Bedienungsanleitung

Sears

Sears 321.596370 Bedienungsanleitung

Eriez

Eriez X8 Bedienungsanleitung

Steinberg Systems

Steinberg Systems SBS-MD-22 Bedienungsanleitung

Zircon

Zircon MetalliScanner m60c Bedienungsanleitung

nalanda

nalanda MD027 Bedienungsanleitung

REV Ritter

REV Ritter CB-7005 Bedienungsanleitung

Minelab

Minelab F1A4 Bedienungsanleitung

Fisher Research Labs

Fisher Research Labs F70 Bedienungsanleitung

Steinberg Systems

Steinberg Systems SBS-MD-12 Bedienungsanleitung

GOLDEN MASK

GOLDEN MASK 5 Bedienungsanleitung

Grizzly

Grizzly YM 203 Bedienungsanleitung

Fisher Research Labs

Fisher Research Labs 1280-X Aquanaut Bedienungsanleitung

Treasure Cove

Treasure Cove Vibra-Probe 560 Bedienungsanleitung

Accurate Locators

Accurate Locators XL16 IMAGER Bedienungsanleitung