TESTO 885 Referenzhandbuch

Andere Handbücher für 885

7

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Beliebte Wärmebildkamera Handbücher anderer Marken

Hikmicro

Hikmicro B20 Bedienungsanleitung

FLIR

FLIR E-EST Series Bedienungsanleitung

FLIR

FLIR M-Series Bedienungsanleitung

BST

BST BT-72 Bedienungsanleitung

CBC

CBC EN7-S02T Bedienungsanleitung

Satir

Satir YRH600 Bedienungsanleitung

TECPEL

TECPEL TIG-320 Bedienungsanleitung

SKF

SKF TKTI 21 Bedienungsanleitung

InfiRay

InfiRay AT300 Series Bedienungsanleitung

InfiRay

InfiRay AT Series Bedienungsanleitung

FLIR

FLIR X6530sc Series Bedienungsanleitung

Videotec

Videotec MAXIMUS MVXT Bedienungsanleitung

Guide Sensmart

Guide Sensmart D384M Bedienungsanleitung

NBN

NBN FLIR A6 Series Bedienungsanleitung

WORKSWELL

WORKSWELL SAFETIS Bedienungsanleitung

Major tech

Major tech MTi11 Bedienungsanleitung

COHU

COHU 5935-1000/T100 Bedienungsanleitung

FLIR

FLIR T4xx series Bedienungsanleitung

testo 885 / testo 890 Thermal Imager

Brief instructions

Overview

Operating concept

The imager can be operated in two different ways.

Operation via touchscreen offers quick access to functions. Joystick operation

enables the imager to be operated with one hand.

Capacitive touchscreen. Operation is only possible with a bare fingertip

(no gloves) or a conductive stylus pen.

This document mentions functions/buttons that have to be activated:

• Touchscreen operation: touch with a fingertip.

• Joystick operation: select first (move joystick up/down/right/left to move the

orange selection box), then activate (press joystick).

Display interface

1Image display: shows IR image or real image.

2Scale display.

3 Imager mode selection bar (capture/image gallery).

4Menu bar/tabbed windows (see below).

5Status displays.

Menu bar / tabbed windows, menu

Functions are called up via the menu bar. The

menu bar comprises 3 tabs. Different functions

are available depending on which tab is

selected.

Via the menu, most functions from the 3 tabs

and many additional functions can be called up.

Open menu:

> | .

Initial operation

Inserting the memory card

1. Open the cover of the bottom interface

terminal (1).

2. Push the memory card (SD or SDHC card)

into the card slot (2).

> To remove the memory card: press the

memory card to release the lock.

Inserting the rechargeable battery

1. Open the battery compartment cover (3) on

the bottom of the imager.

2. Slide rechargeable battery (4) fully into the

battery compartment until it clicks into place.

- The imager starts automatically.

3. Close the battery compartment cover.

Performing basic settings

> Flip open the display and remove the protective film.

- The start screen appears on the display.

- When you first switch on the imager: the Country settings and Set

time/date dialogue boxes are opened one after the other to set the

instrument language, temperature unit (°C/°F) and time/date.

✓ The Country settings dialogue box is

opened.

1. Touch the required language. If necessary,

scroll with / to display other

languages.

- The activated language is indicated with a

tick.

2. Touch to change the unit.

- The activated unit is shown on the top right of

the display.

3. Touch to confirm the entry.

- The Set time/date dialogue box is opened.

4. Touch the top button to open the Time

input screen.

5. Set values for Hour (pm) and Minute with

/ .

6. Touch to confirm the entry.

7. Touch the bottom button to open the

Date input screen.

8. Set values for Month, Day and Year with

/ .

9. Touch to confirm the entry.

10. Touch to close the input screen.

Initial charging of the rechargeable battery

The imager is delivered with a partially charged battery. Fully charge the battery

before use.

> Connect the country-specific adapter

required for the existing mains to the mains

unit.

1. Open the cover of the top interface terminal

(1).

2. Connect the mains unit to the mains socket

(2).

3. Connect the mains plug to a power socket.

- The imager starts automatically.

The rechargeable battery can be recharged with the imager switched on or

off. This has no effect on the time required to charge the battery.

> Hold down [] to close the imager.

- Charging of the battery is started (LED flashes).

4. When the battery is fully charged (steady LED light), disconnect the imager

from the mains unit.

Basic operating steps

Adjusting the hand strap/attaching the lens cover

> Lay the imager on its left side.

1. Open out the top of the hand strap

padding (3).

2. Pull the fastening end of the strap up (4).

3. Put your right hand through the hand strap

from the right-hand side.

4. Adjust the hand strap by loosening/tightening

it to fit your hand and secure the fastening

end again.

5. Fold down the top of the hand strap padding.

> Guide the clip on the lens cover (5) through

the loop on the handle (6).

Rotating the display/handle

CAUTION

Display may be damaged!

> Do not hold the imager by the fold-out display.

> Only fold out and rotate display up to the noticeable stop.

Rotating the display

> Fold out the display (max. 90°) and rotate (max. -180°/+90°).

Rotating the handle

1. Put your right hand through the hand strap.

2. Grip the imager with your left hand. To do

this, hold the casing at the front of the

imager (1).

3. Turn your right hand to move the handle to

the required position (2). Press down with

your middle and ring finger. To rotate in the

opposite direction, press up with the heel of

your hand.

Switching the imager on/off

> Press [](3).

- The start screen appears on the display.

Instrument information is displayed (e.g.

serial number, type designation, firmware

version).

- The measurement view is opened.

Measurement values on the cursor and scale

are only displayed when the stabilisation

phase is complete (indicated by a rotating

symbol in the top right of the display).

The thermal imager performs automatic adjustment approx. every 60 sec. This

can be recognized by means of a "click". The image is frozen briefly when this

occurs.

> To switch off: hold down [](3) until the confirmation prompt is no longer

displayed.

Manually focusing the image

CAUTION

Auto mechanism may be damaged!

> Only turn focusing ring when auto-focus is deactivated (status display top

left: ).

> Deactivate auto-focus: | .

- Status is displayed (top left).

> Turn the lens focusing ring (1) until the

image is in sharp focus.

Automatically focusing the image

> Activate auto-focus: | .

- Status (top left) is displayed.

> Touch [Shutter button] (2).

- An orange box is displayed. The image is

focussed automatically in this area.

Recording (freezing/saving) an image

1. Press [Shutter button] (2).

- The image is frozen (still).

> Select where to save image: touch .

2. Save image: press [Shutter button] again or

touch .

- The IR image is saved and the real image is

automatically attached to the IR image.

> Do not save image: press [Esc] (3).

0971 8851 en 01 V01.00 en-US