Tevion TV5015 Bedienungsanleitung
11
Contents
03 Introduction
04 General Information
Main Features
05 Safety Instructions
10 Assembly and Parts List
Parts List
Remote Control Unit
Installing the batteries
Front panel and rear panel illustration
Connecting to equipment
12 Getting Started
First time installation
Basic operations
Main Menu
Installation
20 FAQ
21 Troubleshooting
22 Specifications
23 Warranty Information
2
Australia 02
Introduction 1
Congratulations on choosing to buy a TEVION product.
All products brought to you by TEVION are manufactured to the highest standards of
performance and safety, and as part of our philosophy of customer service and
satisfaction, are backed by our comprehensive 1 Year Warranty. We hope you will enjoy
using your purchase for many years to come.
3
GeneralInformation 2
Australia 03
This DVB-T Television Receiver, allows you to access free-to-air digital terrestrial TV
channels and radio broadcasts on your TV set. Its digital reception covers VHF & UHF
band. Compared with the analog TV programs, digital TV programs eliminate the noise
and interference but offer high quality video and audio. An initial on-screen installation
guide is provided so that you can easily start to enjoy watching the programs. In addition,
a fully featured remote control is included that offers you access to every feature with a
simple press of a button.
Main Features
. Fully compliant with Australia DVB-T standard
. MPEG2 compliant ISO/IEC 13818 transport stream compliant audio/video decoding
. Bandwidth of 7MHz supported
. COFDM demodulator
. Automatic/manual channel search
. Channel edit, moving and delete
.Parental lock control
. EPG (Electronic Program Guide) and teletext function (where available)
. RS-232 serial port for software upgrade
. Tuner RF in/loop out
. Component/S-Video/Digital Audio via optical output
. HDMI output
. Functional remote control
4
Australia 04
Safety Instructions 3
. Always read the safety instructions carefully.
. Keep this User Manual for future reference.
. Keep this equipment away from humidity.
. Lay this equipment on a reliable flat surface before setting it up.
. Do not stand it on soft furnishings.
If any of the following situations arises, get the equipment checked by a service
technician:
. The equipment has been exposed to moisture.
. The equipment has been dropped and damaged.
. The equipment has obvious sign of breakage.
. The equipment has not been working well or you cannot get it to work according to
User’s Manual.
Warning
. To prevent the risk of electric shock, do not open the cover or the back of the receiver.
. Do not block the ventilation holes of the device. Leave appropriate gap above and
around it to allow for adequate ventilation.
. Do not place the device in an unventilated cabinet or on top of a unit which emits heat.
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to
rain.
5
Australia 05
Assembly and Parts List 4
Parts List
Before installation, please check the items of the package.
The package should contain the following items:
1. DVB-T TV receiver x 1
2. Remote control x 1
3. AAA size battery for the remote control x 2
4. Instruction manual x 1
5. Component Cable x 1
6.Composite cable x 1
6
Australia 06
Assembly and Parts List 4
Remote Control Unit
Key Function
STANDBY：Switch between Operation and Standby mode
NUMBERIC BUTTONS ：Changes channels or selects the menu
options.
FORMAT：To switch to different resolution.
EPG ：Electronic Program Guide button displays the TV/Radio
program guide broadcasting by the TV provider
MENU：Turn to the main menu or return to previous menu
VOL (◄/►)：Turn up/down volume; Change the page of channel
list.
OK：Enter into the menu you choose or select the current option
TXT View the Teletext information
SUBTL ：To display the Subtitle text
PAUSE ：Pause to freeze the screen while watching TV
AUDIO ：Change audio mode to left, right and stereo
MUTE ：Turn off/On volume
TV/RADIO ：Switch between TV and Radio mode
FAV ：Enter into favorite list
INFO ：Display information of programs and current settings
EXIT ：Return to previous menu
CH (▲/▼) ：Change channels or items from top to bottom on the
menu
PAGE UP ：Press to jump one page up or ZOOM up when
enabled
PAGE DOWN ：Press to jump next page or ZOOM down while zoom is enabled
A.RATIO：16:9/4:3
RECALL ：Press to return to previous channel
7
Australia 07
Assembly and Parts List 4
Installing the batteries in the remote control
1. Press down on the retaining catch on the lid of the battery recess on the remote
control and remove the lid.
2. Insert two AAA batteries into the recess.
3. Replace the lid over the recess and gently push down on the lid until it snaps firmly
into place.
Caution
1. Keep batteries out of children’s reach.
2. Don’t attempt to recharge, short-circuit, disassemble, heat or throw the batteries into
the fire.
3. Always replace both batteries at the same time. Never mix new and old batteries or
batteries of a different type.
4. If you don’t intend to use the remote controller for an extended period, remove the
batteries to prevent possible leakage and corrosion.
5. Do not drop, apply shock or step on the remote control.
6. Do not spill water on the remote control.
Note: If the receiver does not operate when operating the remote control from a close
range, you will need to replace the batteries.
Using the Remote Control
1. To use the remote control, point it towards the front of the digital set top box.
2. The remote control has a range of up to 7 metres from the set top box at an angle of
up to 60 degrees.
3. The remote control will not operate if its path is blocked.
Note: Sunlight or very bright light will decrease the sensitivity of the remote
control.
8
Australia 08
Assembly and Parts List 4
Front Panel and Rear Panel Illustration
9
Front Panel
1. STANDBY: To switch the STB between operation and standby modes.
2. CH (-/+): Change channel or items from top to bottom on the menu.
Rear Panel
1. AERIAL IN: Input for antenna.
2. LOOP OUT: Loop signal output to VCR, etc.
3. HDMI connection
4. S/PDIF: S/PDIF audio.
5. S-VIDEO: S-VHS Video output
6. Y/Pb/Pr RCA A/V: Component connection (Y/Pb/Pr)
7. Video RCA A/V: Composite connection
8. Audio (white: left audio, red: right audio): Right & left audio for Component
connection
9. RS-232: To connect to your PC for software upgrade (only used by qualified
technician)
10. POWER: Power ON/OFF switch
Australia 09
Assembly and Parts List 4
Connecting to equipment
Step 1: Connect to the antenna
Connect the antenna lead coming from the wall plate to the AERIAL IN socket.
Step 2: Choose your Connection
There are a number of methods for connecting your STB to the television, depending on
your preference and the connection types on your TV. These methods are labeled A, B
and C below.
A: Y / Pb / Pr (Component) using the supplied RCA blue–red–green lead
For Component video, connect with the supplied Y / Pb / Pr Component cable (green,
blue and red leads). Connect the leads to the Y, Pb and Pr sockets on the back of the unit,
and then to the corresponding Component sockets on your TV. Please pay attention to
the color-coding. You will also need to establish a connection for left and right audio via
the audio sockets. This can be done using the supplied RCA cable.
For right audio, connect the red RCA lead and for left audio, connect the white RCA lead.
B. HDMI connection
If your TV has a HDMI input, you can use a HDMI cable from the back of STB to the rear
of the television. A HDMI lead supplies both audio and visual through the single cable so
no audio leads are necessary.
Please ensure that your television is set to the HDMI input mode for detection of STB
device to be made.
C: CVBS (Composite) using the supplied RCA red–white–yellow lead
Using the appropriate color-coding, you can connect to your TV with the supplied RCA
cable.
For video, connect the yellow RCA lead to the yellow video socket on the back of the
STB and the corresponding socket on your TV.
For right audio, connect the red RCA lead to the red audio socket on the back of the STB
and the corresponding socket on your TV. For left audio, connect the white RCA lead on
the back of the STB and the corresponding socket on your TV.
NOTE: If picture is still not visible on screen, please press the FORMAT button on
the RCU. Keep pressing until 576 is visible on the Set Top Box display screen.
10
Inhaltsverzeichnis
Andere Tevion Set-Top-Box Handbücher
