Texas Instruments TUSB9260 Bedienungsanleitung
TUSB9260 DEMO Board Guide
User's Guide
Literature Number: SLLU131B
July 2010–Revised February 2011
2SLLU131B–July 2010–Revised February 2011
Submit Documentation Feedback
© 2010–2011, Texas Instruments Incorporated
1 TUSB9260 DEMO Board Block Diagram ................................................................................. 5
2 Component Location ........................................................................................................... 6
3 12-V DC Jack ...................................................................................................................... 7
4 Cable Power vs. Self Power .................................................................................................. 8
5 Power Switch ...................................................................................................................... 9
6 3.3-V, 1.8-V, and 1.1-V Regulator ......................................................................................... 10
1 Push Button Reset ............................................................................................................. 10
7 SPI ................................................................................................................................... 11
8 Crystal or Oscillator Support .............................................................................................. 12
9 GPIOs/LEDs/PBUTTON ....................................................................................................... 13
1 GPIO LEDs ....................................................................................................................... 13
2 PWM LEDs ........................................................................................................................ 13
3 GPIO Push Button ............................................................................................................. 13
10 Default GPIO/PWM Configures States .................................................................................. 14
11 Troubleshooting Tips for Windows ...................................................................................... 15
1 Step 1 .............................................................................................................................. 16
2 Step 2 .............................................................................................................................. 16
12 TUSB9260 DEMO Board Schematic ..................................................................................... 18
3
SLLU131B–July 2010–Revised February 2011 Table of Contents
Submit Documentation Feedback © 2010–2011, Texas Instruments Incorporated
www.ti.com
List of Figures
1 Figure 1. DEMO Board Block Diagram .................................................................................. 5
2 Figure 2. Component Location............................................................................................ 6
3 Windows Troubleshooting................................................................................................ 15
4 Disk Management ......................................................................................................... 16
5 Primary Partition........................................................................................................... 16
6 Healthy Disk Status ....................................................................................................... 17
7 Drive in Windows Explorer ............................................................................................... 17
List of Tables
1 Table 1. Frequency Select Map ......................................................................................... 12
2 Table 2. GPIO and PWM Factory Default Settings ................................................................... 14
3 Link Power Status......................................................................................................... 14
4List of Figures SLLU131B–July 2010–Revised February 2011
Submit Documentation Feedback
© 2010–2011, Texas Instruments Incorporated
SLLU131B–July 2010–Revised February 2011
TUSB9260 DEMO Board Block Diagram
Figure 1 represents the block diagram of the TUSB9260 DEMO Board. The board is designed to be
powered from either a 12-V DC wall-wart (not supplied) or via USB cable power.
Figure 1. Figure 1. DEMO Board Block Diagram
5
SLLU131B–July 2010–Revised February 2011 TUSB9260 DEMO Board Block Diagram
Submit Documentation Feedback © 2010–2011, Texas Instruments Incorporated
SLLU131B–July 2010–Revised February 2011
Component Location
Figure 2 shows the general location of major components on the TUSB9260 DEMO Board.
Figure 2. Figure 2. Component Location
6Component Location SLLU131B–July 2010–Revised February 2011
Submit Documentation Feedback
© 2010–2011, Texas Instruments Incorporated
SLLU131B–July 2010–Revised February 2011
12-V DC Jack
The DEMO Board can operate from a standard DC jack for connecting an external 12-V wall-wart. The
wall-wart should be rated for 12 V with at least a 2-A current rating. The tip of the DC jack has positive
polarity. A wall-wart is not supplied with this reference design demonstration module, leaving it capable of
bus power mode by default. In this mode, only Solid State Drives will work. If other higher current hard
drives are to be used a wall-wart will have to be used.
7
SLLU131B–July 2010–Revised February 2011 12-V DC Jack
Submit Documentation Feedback © 2010–2011, Texas Instruments Incorporated
SLLU131B–July 2010–Revised February 2011
Cable Power vs. Self Power
The DEMO Board can be configured to operate off of cable power or use the 12-V wall-wart. To configure
the board to use cable power jumper J4 must have a jumper placed across pins 1 and 2. When configured
for cable power mode only 5-V and 3.3-V are available at the SATA connector. Therefore only SATA
devices such as SSD drives may operate in this mode.
For self power mode J4 must have a jumper placed across pins 2 and 3. In this mode any SATA device
can operate since 12 V, 5 V, and 3.3 V are available at the SATA connector.
8Cable Power vs. Self Power SLLU131B–July 2010–Revised February 2011
Submit Documentation Feedback
© 2010–2011, Texas Instruments Incorporated
SLLU131B–July 2010–Revised February 2011
Power Switch
The DEMO Baord uses a TI TPS2561 power switch. This switch serves two purposes. It limits the amount
of in-rush current on VBUS and it allows power to the SATA connector to be switched via the TUSB9260.
The switch is controlled via GPIO10 from the TUSB9260 and power faults can be monitored by GPIO11.
By default the DEMO Board is configured to always apply power to the SATA connector and power faults
are not monitored.
9
SLLU131B–July 2010–Revised February 2011 Power Switch
Submit Documentation Feedback © 2010–2011, Texas Instruments Incorporated
SLLU131B–July 2010–Revised February 2011
3.3-V, 1.8-V, and 1.1-V Regulator
The DEMO Board utilizes a TI TPS650061 regulator to power the TUSB9260 and associated circuitry.
1 Push Button Reset
Connected to the TPS650061 is a push button (SW2) that can be used to reset the TUSB9260 to its
default state. When pressed the global reset terminal (GRST#) on the TUSB9260 will be driven low.
10 3.3-V, 1.8-V, and 1.1-V Regulator SLLU131B–July 2010–Revised February 2011
Submit Documentation Feedback
© 2010–2011, Texas Instruments Incorporated
Inhaltsverzeichnis
Andere Texas Instruments Computerhardware Handbücher
Texas Instruments
Texas Instruments OMAP36 Series Produkthandbuch
Texas Instruments
Texas Instruments TPS3813 Q1EVM Series Bedienungsanleitung
Texas Instruments
Texas Instruments LM60EVM Bedienungsanleitung
Texas Instruments
Texas Instruments TMS320C3x Bedienungsanleitung
Texas Instruments
Texas Instruments CapTIvate Touch Stücklistenhandbuch
Texas Instruments
Texas Instruments DUAL SOCKET PC CARD CONTROLLER PCI1520... Bedienungsanleitung
Texas Instruments
Texas Instruments Serial Programming Adapter MSP430 Bedienungsanleitung
Texas Instruments
Texas Instruments TPS65910 EVM Bedienungsanleitung
Texas Instruments
Texas Instruments PCI7620 Bedienungsanleitung
Texas Instruments
Texas Instruments MSP430FR5739 Bedienungsanleitung
Texas Instruments
Texas Instruments TAS5707EVM Bedienungsanleitung
Texas Instruments
Texas Instruments OMAP5910 Bedienungsanleitung
Texas Instruments
Texas Instruments CC2540 Bedienungsanleitung
Texas Instruments
Texas Instruments MSP-FET430 Bedienungsanleitung
Texas Instruments
Texas Instruments SimpleLink CC3200 Wi-Fi Bedienungsanleitung
Texas Instruments
Texas Instruments TAS 5611/13PHD2EVM Bedienungsanleitung
Texas Instruments
Texas Instruments DAC38RF8x Bedienungsanleitung
Texas Instruments
Texas Instruments Chipcon Products CC2431 Bedienungsanleitung
Texas Instruments
Texas Instruments TPS65381EVM Bedienungsanleitung
Texas Instruments
Texas Instruments EZShunt INA740 Bedienungsanleitung
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
