Texas Instruments LP8863EVM Bedienungsanleitung
1
SNVU558–February 2017
Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated
The LP8863EVM Evaluation Module
User's Guide
SNVU558–February 2017
The LP8863EVM Evaluation Module
This user’s guide describes the module used to evaluate characteristics, operation, and use of the
LP8863-Q1 automotive LED backlight driver. This document includes a schematic diagram, PCB layout,
and bill of materials (BOM).
Contents
1 Introduction ................................................................................................................... 2
2 Setup .......................................................................................................................... 3
2.1 Input/Output Connector/Header Descriptions................................................................... 4
2.2 LP8863EVM Setup ................................................................................................. 6
2.3 Installation Guide for GUI program (Windows 7-compatible) ................................................. 7
3 Quick Start-Up Procedure................................................................................................. 10
4 Additional Control Options ................................................................................................ 11
5 Instructions for Standalone Evaluation .................................................................................. 16
6 LP8863EVM Board Stackup.............................................................................................. 17
7 LP8863EVM Component Placement .................................................................................... 18
8 LP8863EVM Component List............................................................................................. 19
9 LP8863EVM Schematics.................................................................................................. 22
10 Using the LP8863EVM .................................................................................................... 24
10.1 Power up/down sequence........................................................................................ 24
10.2 Enable .............................................................................................................. 24
10.3 Setting Boost Switch Frequency ................................................................................ 24
10.4 Setting PWM Output Frequency................................................................................. 24
10.5 Setting the LED String Current.................................................................................. 25
10.6 LED String Configuration......................................................................................... 25
11 LED Load Board............................................................................................................ 25
Trademarks
Windows is a registered trademark of Microsoft Corporation.
All other trademarks are the property of their respective owners.
Introduction
www.ti.com
2SNVU558–February 2017
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
The LP8863EVM Evaluation Module
1 Introduction
TI's LP8863-Q1 evaluation module (EVM) helps designers evaluate the operation and performance of the
LP8863-Q1 automotive LED backlight driver. The device offers configurability and can be set up through
external resistor options for boost switching frequency, LED current, and PWM out frequency. Internal
register options enable various controls such as brightness inputs, slope control, dimming options, etc.
The EVM contains one LP8863-Q1 LED driver with boost circuit and a Tiva Launchpad evaluation circuit
to provide control signals for LED driver.
Table 1.
LED DRIVER IC PACKAGE
U8 LP8863-Q1 HTSSOP
Figure 1. LP8863-Q1 Evaluation Board (Top View)
www.ti.com
Setup
3
SNVU558–February 2017
Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated
The LP8863EVM Evaluation Module
Figure 2. LP8863-Q1 Evaluation Board (Bottom View)
2 Setup
This section describes the jumpers and connectors on the EVM as well as how to properly connect and
setup to use the LP8863EVM.
Default resistor values and jumper positions are set to:
• Boost SW frequency – 300 kHz (set by external resistor R59)
• Maximum LED current per string – 120 mA (set by external resistor R57)
• PWM input to control brightness (register control)
• PWM output frequency – 9.8 kHz (set by external resistor R58)
• I2C interface to communicate with LP8863-Q1 – base address 0x2C
• Charge pump for SW gate drive enabled
• J14 : Open to disconnect VDDIO input from VLDO out
• J17 : Open to use internal charge pump
• J19 : Close to connect onboard LDO outputs (1.8 V from Tiva controller circuit) to VDDIO
• J31 : Close to connect onboard LDO output (5 V) to VDD input to LP8863-Q1 measurement
• J12 : Open – probing point of boost output
• J16 : Open – a probing/noise injecting point for stability measurement
Setup
www.ti.com
4SNVU558–February 2017
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
The LP8863EVM Evaluation Module
System/equipment required:
• Power supplies for VIN : 24 V or higher, 6 A or higher
• Power supplies for VDD: 5.5 V or higher, 0.5 A or higher (only needed when external power supply is
used for VDD input. Not needed for default setting)
• Power cables for VIN, VDD connection – cables with banana plugs recommended
• LED load board (not included in package): 6 strings, 8 LEDs per string (LEDs per string can be
adjusted by moving jumpers on load board)
• LED cable: 7-position ribbon cable
• USB cable (USB A to mini)
• PC to run GUI software
• Windows®7 or previous version)
• GUI software
2.1 Input/Output Connector/Header Descriptions
J3 Input— This header is the power input (VDD) terminal and also probing header for LP8863-Q1 power.
The terminal provides a power connection to allow the user to attach the EVM to a power supply
and also monitor VDD connected to J4.
J4 - Input — This banana socket is the power input (VDD) terminal for LP8863-Q1 power. The terminal
provides a power (VDD) connection to allow the user to attach the EVM to a power supply.
J5 - Input— This banana socket is the power input (VBAT) terminal for the boost converter. The terminal
provides a power (VBAT) connection to allow the user to attach the EVM to a power supply.
J6 – GND— This banana socket is the power input (GND) terminal for the boost converter. The terminal
provides a power ground (GND) connection to allow the user to attach the EVM to a power supply.
J7 – Header— This header is a probing point of SW node.
J8 – GND— This banana socket is the power input (GND) terminal for the boost converter. The terminal
provides a power ground (GND) connection to allow the user to attach the EVM to a power supply.
www.ti.com
Setup
5
SNVU558–February 2017
Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated
The LP8863EVM Evaluation Module
J9 – Input— This header is the power input (VBAT) terminal and also probing header for the boost
converter. The terminal provides a power connection to allow the user to attach the EVM to a power
supply and also monitor VBAT connected to J5.
J10 – Header — This header is a probing point of VIN (boost input power after power filters).
J11 – Header— This header is a probing point of VINP (boost input power after power line FET).
J12 – Headers— These headers are probing points of boost output (VBOOST).
J13 – GND— This header is the power input (GND) terminal and also probing header for the boost
converter. The terminal provides power ground connection to allow the user to attach the EVM to a
power supply and also monitor VBAT connected to J8.
J14 – Jumper— This connector is for selection of the source of VDDIO between VDD and internal LDO
out (VLDO) of LP8863-Q1.
J15 – Input— This header is the power input (VDDIO) terminal and also probing header for VDDIO. The
terminal provides a power connection to allow the user to attach the EVM to a power supply and
also monitor VDDIO selected by J14.
J16 – Headers— These headers are probing/noise injecting points for stability measurement of boost.
J17 – Connector— This connector is to connect VDD to the internal charge pump output (when charge
pump is not used).
J18 – Header— This header is a probing point of GD.
J19 – Jumper— This connector is for selection of the source of VDDIO between 1.8-V and 3.3-V output
from on-board LDOs.
J20 – Connector— This connector is to connect 5-V output from on-board LDO to VDD input.
J21 to J26 – Headers— These headers are to measure LED string current of LED0 to LED5.
J27 – GND— These headers are probing points of GND.
J28 – Header— This header is a probing point of INT.
J31 – Connector— This connector is to connect 5-V output from on-board LDO to VDD input.
J32 – Headers— These headers are probing points of SDO_PWM, SDI_SDA, SCLK_SCL, and
SS_ADDRSEL.
J33 – Connector— This connector is to connect LED load board to EVM.
J34 – GND— These headers are probing points of GND.
Setup
www.ti.com
6SNVU558–February 2017
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
The LP8863EVM Evaluation Module
2.2 LP8863EVM Setup
External power must be provided to the board. Connect a standard type-A plug from the PC to a Mini-B
plug, which goes to the EVM connector. The I2C-compatible interface program provides all of the controls
that the LP8863-Q1 device requires.
Figure 3. LP8863EVM With LED Load Board Connected
www.ti.com
Setup
7
SNVU558–February 2017
Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated
The LP8863EVM Evaluation Module
2.3 Installation Guide for GUI program (Windows 7-compatible)
• Run “setup_LP8863_EVM_1.0.0.exe”.
• Click “Next” button on this setup screen.
Figure 4. LP8863_EVM_GUI Setup
• Check ”I accept the agreement” and press ”Next” button again.
Setup
www.ti.com
8SNVU558–February 2017
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
The LP8863EVM Evaluation Module
Figure 5. License Agreement
• Choose the folder name of GUI to be installed, then press ”Next” button or simply press ”Next” button.
Figure 6. Installation Directory
www.ti.com
Setup
9
SNVU558–February 2017
Submit Documentation Feedback Copyright © 2017, Texas Instruments Incorporated
The LP8863EVM Evaluation Module
• Begin SW installation by pressing ”Install” button in next window.
• Once installation is completed, press ”Finish” to launch SW GUI of LP8863-Q1.
Figure 7. Completing the LP8863_EVM_GUI Setup Wizard
• Initial window of GUI. Prepare hardware connection after this window, as described in the following
sections.
Figure 8. LP8863_EVM_GUI Home Page
Quick Start-Up Procedure
www.ti.com
10 SNVU558–February 2017
Submit Documentation Feedback
Copyright © 2017, Texas Instruments Incorporated
The LP8863EVM Evaluation Module
3 Quick Start-Up Procedure
• Connect USB cable between EVB and PC.
• Connect external power supply to VIN: 12 V (typical), 5-A setting, output not enabled yet.
• Run the LP8863 GUI software and click ”Control” icon on left of GUI, then control window appears
as in Figure 9.
Figure 9. GUI Control Window
• Check ”EVM connected” mark on bottom of GUI software.
• Press ”IFSEL Pin” button to select I2C interface: This is not required if register control is not used.
• Enable VIN power supply output: IIN is approximately a couple of mA at normal cases. If higher current
on either power rail is monitored, disable power supply output and begin debugging.
• Click ”Enable Pin” button on GUI software: boost converter starts working, and LEDs stay off without
PWM input.
• On PWM input control, check ”Enable” box of PWM input, select frequency and duty from drop-down
boxes, and press ”Update” button: LED turns on at adjusted brightness level by PWM input.
Inhaltsverzeichnis
Andere Texas Instruments Steuereinheit Handbücher
Texas Instruments
Texas Instruments THS7001 Bedienungsanleitung
Texas Instruments
Texas Instruments TPA2039D1 Bedienungsanleitung
Texas Instruments
Texas Instruments BQ25672EVM Bedienungsanleitung
Texas Instruments
Texas Instruments OPT3004DTSEVM Bedienungsanleitung
Texas Instruments
Texas Instruments TRF7962A Bedienungsanleitung
Texas Instruments
Texas Instruments BQ24260EVM-611 Bedienungsanleitung
Texas Instruments
Texas Instruments bq76PL536 EVM Bedienungsanleitung
Texas Instruments
Texas Instruments LED171596AEVM Bedienungsanleitung
Texas Instruments
Texas Instruments TPS65320C-Q1-EVM Bedienungsanleitung
Texas Instruments
Texas Instruments TRF3750 Series Bedienungsanleitung
Texas Instruments
Texas Instruments TPSM846C23 Bedienungsanleitung
Texas Instruments
Texas Instruments BQ76905 Bedienungsanleitung
Texas Instruments
Texas Instruments TPS6101xEVM-157 Bedienungsanleitung
Texas Instruments
Texas Instruments TPS630702EVM Bedienungsanleitung
Texas Instruments
Texas Instruments TAS2563 Bedienungsanleitung
Texas Instruments
Texas Instruments DRV2605LEVM-MD Bedienungsanleitung
Texas Instruments
Texas Instruments MSP-EXP430G2 Bedienungsanleitung
Texas Instruments
Texas Instruments BQ24180 Bedienungsanleitung
Texas Instruments
Texas Instruments DP159RSB Bedienungsanleitung
Texas Instruments
Texas Instruments TPS40200 Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
