Texas Instruments TRF2443 Bedienungsanleitung
AGC
CNTL
7
0/90TXPLL
3
RXAGC
VCCs
GNDs
RXPLL
TXQ_IN
TX_OUT
TXI_IN
RX_IN
RX VGA
TX VGA
IFAMP
From SPI
from RXPLL
XPIC_IN
XPIC
OUT
XPIC
AGC
XPIC_BBI
XPIC_BBQ
Level
Detect
IF SAW
IF_OUT IF_IN
TX_PWD
Temperature
Sensor
CLKSPI
DATASPI
LESPI
RXBBI
RXBBQ
TEMPOUT
0/90
0/90
S
P
I
User's GuideSLWU065 – September 2009
TRF2443 Integrated IF Transceiver Evaluation Module
This document provides an easy guide for evaluating the TRF2443 integrated IF transceiver for broadbandwireless applications. Included in this guide are equipment setup procedures, software GUI configurations,and test procedures that allow a user to quickly and accurately measure the TRF2443 performance.
The TRF2443 is a fully integrated IF transceiver operating at a transmitter IF of 340 MHz (or 170 MHz)and a receiver IF of 140 MHz (or 280MHz). The IF transceiver is used to for up-conversion of signals fromthe transmit chain digital-to-analog convertor (DAC) to the RF upconverter device and fordown-conversion of received IF signals to baseband for processing by the analog-to-digital convertor(ADC). The receiver allows for switching in an external SAW filter if needed or by-passing this filter andprocessing the signal completely internally. The TRF2443 also provides an Auxiliary Receiver which canbe used for cross-polarization interference cancellation (XPIC). This document describes how to test theTRF2443 as well as the many options for trimming the device configuration to meet your applicationneeds.
Figure 1. TRF2443 Block Diagram
SLWU065 – September 2009 TRF2443 Integrated IF Transceiver Evaluation Module 1Submit Documentation Feedback
www.ti.com
Contents1 EVM Circuit Overview ....................................................................................................... 41.1 DC POWER ......................................................................................................... 41.2 Reference Clock .................................................................................................... 51.3 Communications .................................................................................................... 51.4 Transmitter ........................................................................................................... 51.5 Receiver .............................................................................................................. 61.6 XPIC Receiver....................................................................................................... 92 GUI Overview ............................................................................................................... 102.1 GUI for Synthesizers .............................................................................................. 122.2 GUI for Receiver ................................................................................................... 142.3 GUI Transmitter.................................................................................................... 152.4 GUI for XPIC Receiver ........................................................................................... 153 TRF2443 EVM Operating Procedures ................................................................................... 163.1 Power Up ........................................................................................................... 163.2 Receiver ............................................................................................................ 173.3 XPICOUT Amplifier ............................................................................................... 183.4 Transmitter ......................................................................................................... 193.5 EEPROM ........................................................................................................... 203.6 XPIC RECEIVER .................................................................................................. 214 Physical Description ....................................................................................................... 234.1 EVM Top Layer Drawing ......................................................................................... 234.2 Bill of Materials .................................................................................................... 244.3 Schematics ......................................................................................................... 26
List of Figures
1 TRF2443 Block Diagram .................................................................................................... 12 TXPWD Header JP1 Schematic ........................................................................................... 43 EVM DC Power: J1, J2, and JP1 .......................................................................................... 44 EVM Reference Clock J3 and USB Port J5 .............................................................................. 55 TX Baseband Inputs ......................................................................................................... 66 J7 (RXIN) ..................................................................................................................... 67 RX Baseband Outputs ...................................................................................................... 78 SAW Filter Path .............................................................................................................. 89 XPIC RX ...................................................................................................................... 910 TRF2443 GUI Quick-Set Tab ............................................................................................. 1011 TRF2443 GUI Advanced Tab ............................................................................................. 1112 Load All Registers .......................................................................................................... 1213 Reset USB .................................................................................................................. 1214 Synthesizer Programming ................................................................................................. 1215 RX GUI ...................................................................................................................... 1416 RX AGC GUI ................................................................................................................ 1417 Transmitter GUI............................................................................................................. 1518 XPIC Receiver GUI ........................................................................................................ 1519 XPIC AGC GUI ............................................................................................................. 1520 Programmed ICC GUI Settings ........................................................................................... 1621 Load All Registers .......................................................................................................... 1622 Receiver SAW Disabled GUI Settings ................................................................................... 1723 Receiver SAW Enabled GUI Settings ................................................................................... 1824 Receiver XPICOUT GUI Settings ........................................................................................ 1925 TX Max Gain GUI Settings ................................................................................................ 1926 GUI Settings for TX Carrier Leakage .................................................................................... 2027 GUI Show Readback ...................................................................................................... 20
2List of Figures SLWU065 – September 2009Submit Documentation Feedback
www.ti.com
28 GUI Select EEPROM Readback ......................................................................................... 2029 Read I/Q Carrier Leakage Trim Values B < 10,5> ...................................................................... 2130 TX Carrier Leakage Trim .................................................................................................. 2131 XPIC Receiver Max Gain GUI ............................................................................................ 2232 XPIC Receiver Min Gain GUI ............................................................................................. 2233 TRF2443 EVM Top Layer ................................................................................................. 2334 Schematic (1 of 5) .......................................................................................................... 2635 Schematic (2 of 5) .......................................................................................................... 2736 Schematic (3 of 5) .......................................................................................................... 2837 Schematic (4 of 5) .......................................................................................................... 2938 Schematic (5 of 5) .......................................................................................................... 30
List of Tables
1 Bill of Materials ............................................................................................................. 24
SLWU065 – September 2009 List of Tables 3Submit Documentation Feedback
1 EVM Circuit Overview
1.1 DC POWER
GND
+3.3V
JP1
TXPWD
1
3
2TXPWD
80
SHUNT 2-3
S006
EVM Circuit Overview
www.ti.com
The TRF2443 EVM requires a 3.3V dc power-supply connected to between J1 (3.3V) and J2 (GND). TheTRF2443 allows for analog or digital control of the transmitter power supply. Pin 1 (TXPWD) of the deviceprovides the analog control and is connected to header JP1 (TXPWD) on the EVM. When pins 1 and 2 ofheader JP1 are shorted, 3.3V is fed to the TXPWD pin and the transmitter is disabled. When pins 2 and 3of header JP1 are shorted, 0V is fed to the TXPWD pin and the transmitter is enabled (see Figure 2 andFigure 3 ). With header JP1 enabling the transmitter, it is still possible for the transmitter to be off due tothe state of the digital TX control.
Figure 2. TXPWD Header JP1 Schematic
Figure 3. EVM DC Power: J1, J2, and JP1
List of Tables4 SLWU065 – September 2009Submit Documentation Feedback
1.2 Reference Clock
1.3 Communications
1.4 Transmitter
www.ti.com
EVM Circuit Overview
The TRF2443 EVM allows for either an external reference chosen by the user or an internal oscillator at20 MHz provided on the EVM board. If an external reference is to be used the signal should be fed intoSMA connector J3 (EXTREF) and jumpers W1 and W12 should be removed (see Figure 4 ).
Figure 4. EVM Reference Clock J3 and USB Port J5
The EVM is equipped with USB communications which provide the interface between a computer's USBport and the TRF2443s SPI port via J5 as shown in Figure 4 . A CD containing the GUI to control theTRF2443 is provided within the EVM kit. An overview of the GUI is provided in this document
The EVM is configured for differential I/Q input signals via four SMA connectors. For the upper sideband,the I signals are connected to J12 (TXBBIP) and J17 (TXBBIN). The Q signals are connected to J23(TXBBQN) and J20 (TXBBQP) (see Figure 5 ). SMA connector J6 (TXOUT), not shown below, is used tomonitor the RF output signal from the transmitter.
SLWU065 – September 2009 List of Tables 5Submit Documentation Feedback
1.5 Receiver
RXIN
50 OHM DIFF
50 OHM
220pF220pF
RXINP
68
RXINN
69
GNDRX
70
GNDRX
71
VCCRX
67
220pF
S007
EVM Circuit Overview
www.ti.com
Figure 5. TX Baseband Inputs
The EVM is configured for single ended RX input signal via SMA connector J7 (RXIN). This input is takenthrough a 1:1 balun to provide differential inputs to the device. The device presents 50 so no externaltermination resistor is required.
Figure 6. J7 (RXIN)
6List of Tables SLWU065 – September 2009Submit Documentation Feedback
www.ti.com
EVM Circuit Overview
The baseband I/Q signals can be measured balanced or unbalanced. The I output is taken from theunbalanced port J15 (RXBBI) through balun T5 or from the balanced ports of J13 (I+) and J18 (I-).Likewise, the Q output is taken from the unbalanced port J24 (RXBBQ) through balun T7 or the balancedports of J21 (Q+) and J26 (Q-). For balanced mode measurements, jumpers W3, W5, W7 and W9 mustbe removed.
Figure 7. RX Baseband Outputs
SLWU065 – September 2009 List of Tables 7Submit Documentation Feedback
EVM Circuit Overview
www.ti.com
The TRF2443 RX path allows the use of an external SAW filter. An internal switch, which is programmablethrough the serial interface, gives the flexibility to utilize the external filter (see Figure 1 ). The internalswitch is controlled via the serial programming interface through bit EN_SAW. By programming EN_SAWto 1, the external path is selected, whereas a 0 engages the internal bypass switch. When EN_SAW is setto 1 the IF signal will be routed out of the IC to SMA connector J30 (IFOUT) (see Figure 8 ). At this point,the user has the flexibility to insert a filter of choice outside the TRF2443 EVM. (The board does contain aplace holder (FL1) for a SAW filter but is not populated. In this way, the user has the flexibility to use afilter of his choice). For initial evaluation, an 8-10 dB pad can be used in lieu of a filter to emulate theinsertion loss of a typical filter. The user must route the signal from J30 (IFOUT) to J31 (IFIN) with the filteror pad included.
Figure 8. SAW Filter Path
List of Tables8 SLWU065 – September 2009Submit Documentation Feedback
1.6 XPIC Receiver
www.ti.com
EVM Circuit Overview
The TRF2443 provides an auxiliary receiver chain that can be used for cross-polarization interferencecancellation purposes. The EVM is configured for a single-ended output signal (intended for the secondaryXPIC RX path) at J33 (XPICOUT). The input to the XPIC receiver (from the XPICOUT of the secondaryXPIC RX path) is available at SMA connector J32 (XPICIN). This input is taken through a 1:1.5 balun toprovide differential inputs to the device. The device presents 75 so no external termination resistor isrequired. The XPIC baseband I and Q signals can be measured balanced or unbalanced. The I output istaken from the unbalanced port J16 (XPICI) through balun T6 or from the balanced ports of J14 (I+) andJ19 (I-). Likewise, the Q output is taken from the unbalanced port J25 (XPICQ) through balun T8 or thebalanced ports of J22 (Q+) and J27 (Q-). For balanced mode measurements, jumpers W4, W6, W8, andW10 must be removed (see Figure 9 ).
Figure 9. XPIC RX
SLWU065 – September 2009 List of Tables 9Submit Documentation Feedback
2 GUI Overview
GUI Overview
www.ti.com
The TRF2443 EVM kit includes a graphical user interface for controlling the device. The GUI contains twotabs labeled "Quick-set" and "Advanced" (see Figure 10 and Figure 11 )
Figure 10. TRF2443 GUI Quick-Set Tab
10 List of Tables SLWU065 – September 2009Submit Documentation Feedback
Inhaltsverzeichnis
Andere Texas Instruments Steuereinheit Handbücher
Texas Instruments
Texas Instruments AFE79 Series Montageanleitung
Texas Instruments
Texas Instruments SimpleLink Wi-Fi CC3 20 Series Bedienungsanleitung
Texas Instruments
Texas Instruments TLVM13660 Bedienungsanleitung
Texas Instruments
Texas Instruments THS7001 Bedienungsanleitung
Texas Instruments
Texas Instruments TPS54331 Bedienungsanleitung
Texas Instruments
Texas Instruments TPSM846C24 Bedienungsanleitung
Texas Instruments
Texas Instruments TPS254900AQ1EVM-003 Bedienungsanleitung
Texas Instruments
Texas Instruments TPS2388EVM-612 Bedienungsanleitung
Texas Instruments
Texas Instruments DAC8580 Bedienungsanleitung
Texas Instruments
Texas Instruments LMG352 EVM-04 Series Bedienungsanleitung
Texas Instruments
Texas Instruments DAC1220EVM Bedienungsanleitung
Texas Instruments
Texas Instruments DRV10964 Bedienungsanleitung
Texas Instruments
Texas Instruments TPS7A78EVM-011 Bedienungsanleitung
Texas Instruments
Texas Instruments UCC25600EVM Bedienungsanleitung
Texas Instruments
Texas Instruments TAS6424R-Q1 Bedienungsanleitung
Texas Instruments
Texas Instruments UCC2 5 EVM-286 Series Bedienungsanleitung
Texas Instruments
Texas Instruments TPSM8282xEVM-080 Bedienungsanleitung
Texas Instruments
Texas Instruments MCF8316AEVM Bedienungsanleitung
Texas Instruments
Texas Instruments OPT8241-CDK-EVM Bedienungsanleitung
Texas Instruments
Texas Instruments SWIFT TPS548A20 Bedienungsanleitung
Texas Instruments
Texas Instruments BoosterPack Educational Plug-in Module Mark II... Bedienungsanleitung
Texas Instruments
Texas Instruments TPS62737 Bedienungsanleitung
Texas Instruments
Texas Instruments SimpleLink BoosterPack BOOSTXL-CC3120MOD Bedienungsanleitung
Texas Instruments
Texas Instruments TPA721 Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
