Texas Instruments ADS8472EVM Bedienungsanleitung

User's GuideSLAU203 – February 2007

ADS8472EVM

This user guide describes the characteristics, operation, and use of the ADS8472 16-bit, 1MHz parallelinterface analog-to-digital converter evaluation board. A complete circuit description as well as schematicdiagram and bill of materials is included.

Contents1 EVM Overview ............................................................................................................... 22 Introduction ................................................................................................................... 23 Analog Interface .............................................................................................................. 24 Digital Interface .............................................................................................................. 55 Power Supplies .............................................................................................................. 76 Using the ADS8472EVM .................................................................................................... 87 ADS8472EVM BoM ........................................................................................................ 108 ADS8472EVM Layout ..................................................................................................... 129 ADS8472EVM Schematic ................................................................................................. 15

List of Figures

1 Input Buffer, Bipolar Fully Differential Input .............................................................................. 42 Top – Layer 1 ............................................................................................................... 123 Ground Plane – Layer 2 ................................................................................................... 134 Power Plane – Layer 3 .................................................................................................... 135 Bottom – Layer 4 ........................................................................................................... 146 Top Overlay ................................................................................................................ 147 Bottom OverLay ............................................................................................................ 15

List of Tables

1 Analog Input Connector ..................................................................................................... 32 Analog Circuitry Jumper Configurations .................................................................................. 43 Pinout for Parallel Control Connector P3 ................................................................................. 54 Jumper Settings .............................................................................................................. 55 Data Bus Connector P2 ..................................................................................................... 66 TSW1100 Connector ........................................................................................................ 67 Pin out for Converter Control Connector, J6 ............................................................................. 78 Power Supply Test Points .................................................................................................. 79 Power Connector, J5, Pin Out ............................................................................................. 710 Bill of Materials ............................................................................................................. 10

SLAU203 – February 2007 ADS8472EVM 1Submit Documentation Feedback

1 EVM Overview

1.1 Features

1.2 Related Documentation from Texas Instruments

2 Introduction

3 Analog Interface

EVM Overview

www.ti.com

•Full-featured Evaluation Board for the high-speed ADS8472 16-bit, 1MSPS single channel, parallelinterface SAR type Analog to Digital Converters.•On board signal conditioning•On board Reference•Input and Output Digital Buffers•On board decoding for stacking multiple EVMs.

To obtain a copy of any of the following TI documents, call the Texas Instruments Literature ResponseCenter at (800) 477-8924 or the Product Information Center (PIC) at (972) 644-5580. When ordering,identify this booklet by its title and literature number. Updated documents can also be obtained throughour website at www.ti.com .

Data Sheets: Literature Number:ADS8472 SLAS514REF3240 SBVS058REF3225 SBVS058SN74AHC138 SCLS258SN74AHC245 SCLS230SN74AHC1G04 SCLS318THS4031 SLOS224THS4032 SLOS224

The ADS8472 is 16-bit, 1-MSPS analog to digital converter (ADC) with an internal 4.096V reference and apseudo-bipolar, fully differential input. The device is a capacitor based successive approximation register(SAR) converter with an inherent sample and hold. The ADS8472 has a 16-bit and 8-bit parallel interfacebus options, allowing a variety of processors to interface easily with it.

The ADS8472EVM is an evaluation and demonstration platform for the ADS8472 ADC. The board is aflexible design that allows the user to choose among many different analog signal conditioning, referenceand interface modes. The standardized I/O headers not only allow the user to quickly interface to FPGAs,but also to the full line of microprocessors and digital signal processors from Texas Instruments.

The analog-to-digital converter accepts a pseudo-bipolar differential input. A pseudo-bipolar differentialsignal is a fully differential signal that has a common-mode voltage such that the voltage on each input isalways equal to or above zero volts. The common mode voltage should typically be half the referencevoltage. The peak-to-peak amplitude on each input leg can be as large as the reference voltage.

The positive leg of the input signal can be applied at connector P1 pin 2 (shown in Table 1 ) or via centerpin of SMA connector J1. Likewise the negative input signal can be applied at P1 pin1 or via center pin ofSMA connector J2.

ADS8472EVM 2 SLAU203 – February 2007Submit Documentation Feedback

3.1 Input Signal Conditioning

www.ti.com

Analog Interface

Table 1. Analog Input Connector

Description Signal Name Connector.Pin# Signal Name Description

Inverting Input Channel — P1.1 P1.2 + Non-inverting Input ChannelReserved N/A P1.3 P1.4 N/A ReservedReserved N/A P1.5 P1.6 N/A ReservedReserved N/A P1.7 P1.8 N/A ReservedReserved N/A P1.9 P1.10 N/A ReservedPin tied to Ground AGND P1.11 P1.12 N/A ReservedPin tied to Ground AGND P1.13 P1.14 N/A ReservedN/A Reserved P1.15 P1.16 N/A ReservedPin tied to Ground AGND P1.17 P1.18 N/A ReservedPin tied to Ground AGND P1.19 P1.20 REF+ External Reference Input

The analog input circuitry, consisting of the THS4031 and THS4032 operational amplifiers, allow the userto install passive components to configure it for positive or negative gains, as well as input range scaling,filtering and leveling translation (e.g., adding a DC offset). The operational amplifiers are housed in anindustry standard SOIC footprint. This enables the user to replace the THS4031 with a plethora of dualand single supply amplifiers housed in an SOIC package.

When choosing the driver amplifier the user should consider the following requirements. The drivingamplifier must be able to settle the input to 16-bit level within the sample time of the converter. It shouldhave Total Harmonic Distortion(THD) characteristics comparable to or better than the ADS8472. Lastly,the noise generated by the amplifier needs to be as low as possible, so as not to degrade the SNRperformance of the ADS8472.

The noise coming through the driver amplifiers are filtered by a single-pole filter using R = 10.2 Ωand C=2.2nF with a corner frequency of 7MHz. The 5.1- Ωseries resistor works with the capacitor to filter the inputsignal, but also isolates the amplifier from the capacitive load. The 2200-pF capacitor to ground at theinput of the ADC works with the series resistor to filter the input signal, behaves like a charge reservoir,and provides a path to ground for high-frequency noise and the low small input current transient whichoccurs when the device switches from hold to sample mode. This external filter capacitor works with theamplifier to charge the internal sampling capacitor during sampling mode.

The supplies to the input amplifier are selectable with solder jumper pad SJP3, and SJP4. Shorting acrosspads 1 and 2 will ground the negative rail. Shorting across pads 2 and 3 will tie the negative supply of theamplifiers to the voltage applied at node –VCC.

When deciding on supply rails, a good rule of thumb is to add at least 2V of head room on either side toachieve optimal performance. For example, if the signal applied to the amplifier is 0–4V, then the amplifierrails should be at least –2V and +6V. At the 16-bit performance node, the amplifier introduced distortioncan become significant. Be aware when reading amplifiers data sheets that they may not be specified withlarge amplitudes. Therefore, it may not be possible to surmise from a cursory glance how well theamplifier will behave in system.

Single-ended signal sources are readily available, but rarely allow the user to evaluate the fullperformance of 16-bit converters. Although the ADS8472EVM can be configured for this inputconfiguration, the factory set configuration of the input circuitry is for a bipolar fully differential input signal.The necessary DC component to offset the signal at U7 is generated by U4. U4 is the low noise THS4032amplifier. It can be configured to further filter the reference voltage IC, U2, and provide positive or negativegains. The ADS8472EVM leaves the factory with potentiometer, R24, set to 2.048V and set as shown inFigure 1 .Table 1 indicates how the solder pad jumpers should be set to select from the various supplyand input options for the analog driver circuitry. The copy of the schematic for the ADS8472EVM isattached at the end of this document.

SLAU203 – February 2007 ADS8472EVM 3Submit Documentation Feedback

-6 V

+6 V

THS4031

2.2 nF

(+)IN

0.1 Fm

C11

+Vin

-4 V to +4 V

C45

R39

0-4 V

R36

-6 V

+6 V

THS4031 (-)IN

C13

R40

0-4 V

R38

4.096 V

-Vin

-4 V to +4 V

4.096 V

R31

R37

R21

75 W

C12

0.1 Fm

5.1 W

1000 W

5.1 W

C14

0.1 Fm

75 W

0.1 Fm

1000 W

3.2 Reference

Analog Interface

www.ti.com

Figure 1. Input Buffer, Bipolar Fully Differential Input

Table 2. Analog Circuitry Jumper Configurations

Reference 1-2 2-3 DescriptionDesignator

SJP1 Installed †

(1)

Not Installed Select onboard reference (REF3230).Not Installed Installed Select user-supplied reference at P1 pin 20.SJP2 Installed †

(1)

Not Installed Set REFIN pin of ADS8472 to on-chip (internal) reference voltage.Not Installed Installed Set REFIN pin of ADS8472 to reference selected by SJP1.SJP3 Installed Not Installed Set U6 operational amplifier minus rail supply to ground.Not Installed Installed †

(1)

Set U6 operational amplifier minus rail supply to –VCC.SJP4 Installed Not Installed Set U7 operational amplifier minus rail supply to ground.Not Installed Installed †

(1)

Set U7 operational amplifier minus rail supply to –VCC.SJP5 Not Installed N/A Short voltage node –DC to U6 pin 2 via R35.SJP6 Not Installed N/A Short –IN pin of U5 to ground at C45.

(1)

† Indicates factory installed option.

The ADS8472 can operate with an external reference voltage in the range of 3.0V up to 4.2V. It generatesan on-chip 4.096V reference voltage. The ADS8472EVM allows the user to select the external referencevoltage from three sources. The first option is to use the internally generated 4.096V from the ADC. Theother two options are to select from the on board reference (U1) or a user supplied voltage applied at pin20 of P1. Refer to Table 1 for solder jumper options for selecting from the various reference sources.

4ADS8472EVM SLAU203 – February 2007Submit Documentation Feedback

4 Digital Interface

www.ti.com

Digital InterfaceThe reference voltage provides the scale factor for the conversion result. The input voltage is measuredagainst the reference voltage. It is imperative the reference voltage be clean, low noise and welldecoupled.

The default configuration is to use the internal on-chip reference.

The ADS8472EVM is designed for easy interfacing to multiple platforms. The digital interface input andoutput signals of the converter are on connectors P2, P3, J6 and J7. These are 0.1" on-centers, plug andsocket connectors, allowing the user to plug the ADS8472EVM onto the various motherboard interfacecards from Texas Instruments, or ribbon cable onto the user development board. The following tables listthe connector pin outs.

Table 3. Pinout for Parallel Control Connector P3

Description Signal Name Connector.Pin# Signal Name Description

Not connected DC_CS P3.1 P3.2 + Non-inverting Input ChannelReserved N/A P3.3 P3.4 GND GroundReserved N/A P3.5 P3.6 GND GroundAddress line 0 A0 P3.7 P3.8 GND GroundAddress line 1 A1 P3.9 P3.10 GND GroundAddress line 2 A2 P3.11 P3.12 GND GroundReserved N/A P3.13 P3.14 GND GroundReserved N/A P3.15 P3.16 GND GroundConvert Start DC_CONVST P3.17 P3.18 GND GroundInterrupt pin INTC P3.19 P3.20 GND Ground

Conversions are initiated on the falling edge of the convert start signal. It is therefore critical whenmeasuring large amplitude and/or high frequency input signals, the user provide a clean low jitter convertstart pulse.

The convert start signal can be applied to the ADS8472 from the decoder outputs or from connector P3pin 17. Address decoder SN74ACH138 is used to generate the read ( RD) and conversion start ( CONVST)signals to the converter. Jumpers W3 and W4 allow the user to assign these two signals to differentaddresses in memory. This allows for the stacking of up to two ADS8472EVMs into processor memory.See Table 3 for jumper settings. If the user applies a convert start signal directly on P3 pin 17, then besure to short W6 pins 1-2. This will bypass the decoder output selected by position of W4.

Note, the evaluation module does not allow chip select ( CS) line of the converter to be assigned todifferent memory locations. It is therefore suggested the CS line be grounded or wired to an appropriatesignal of the processor.

Table 4. Jumper Settings

Reference Description 1-2 2-3Designator

W1 Set digital buffer supply voltage to +5V Installed Not installedSet digital buffer supply voltage to +3.3V Not installed Installed †

(1)

W2 Apply inverted BUSY to INTC signal Installed †

(1)

Not installedApply BUSY signal to INTC signal Not installed InstalledW3 Set RD signal to add[0x3] Installed Not installedSet RD signal to add[0x4] Not installed InstalledW4 Set CONVST signal to add[0x1] Installed Not installedSet CONVST signal to add[0x2] Not installed Installed

(1)

† Indicates factory installed option.

SLAU203 – February 2007 ADS8472EVM 5Submit Documentation Feedback

Digital Interface

www.ti.com

Table 4. Jumper Settings (continued)

Reference Description 1-2 2-3Designator

W5 Set DC_CS to CS of ADS8472 Installed N/AW6 Set DC_CONVST to CONVST of ADS8472 Installed InstalledSet decoder output to CONVST of ADS8472 Not installed Installed

The data bus is available at connector P2, see Table 4 for pin out information.

Table 5. Data Bus Connector P2

Description Signal Name Connector.Pin# Signal Name Description

Reserved N/A P2.1 P2.2 GND GroundReserved N/A P2.3 P2.4 GND GroundData Bit 0 DB0 P2.5 P2.6 GND GroundData Bit 1 DB1 P2.7 P2.8 GND GroundData Bit 2 DB2 P2.9 P2.10 GND GroundData Bit 3 DB3 P2.11 P2.12 GND GroundData Bit 4 DB4 P2.13 P2.14 GND GroundData Bit 5 DB5 P2.15 P2.16 GND GroundData Bit 6 DB6 P2.17 P2.18 GND GroundData Bit 7 DB7 P2.19 P2.20 GND GroundData Bit 8 DB8 P2.21 P2.22 GND GroundData Bit 9 DB9 P2.23 P2.24 GND GroundData Bit 10 DB10 P2.25 P2.26 GND GroundData Bit 11 DB11 P2.27 P2.28 GND GroundData Bit 12 DB12 P2.29 P2.30 GND GroundData Bit 13 DB13 P2.31 P2.32 GND GroundData Bit 14 DB14 P2.33 P2.34 GND GroundData Bit 15 DB15 P2.35 P2.36 GND Ground

In addition to interfacing to the various micro controller and digital signal processors from TexasInstruments, this board also plugs into the TSW1100 card. The TSW1100 is a PC-based data capturecard. J7 connector is installed to allow the user to plug the ADS8472EVM directly and collect data foranalysis.

Table 6. TSW1100 Connector

Description Signal Name Connector.Pin# Signal Name Description

Ground Ground J7.1 J7.2 N/C Not ConnectedGround Ground J7.3 J7.4 N/C Not ConnectedGround Ground J7.5 J7.6 D0 Data Bit 0 (LSB)Ground Ground J7.7 J7.8 D1 Data Bit 1Ground Ground J7.9 J7.10 D2 Data Bit 2Ground Ground J7.11 J7.12 D3 Data Bit 3Ground Ground J7.13 J7.14 D4 Data Bit 4Ground Ground J7.15 J7.16 D5 Data Bit 5Ground Ground J7.17 J7.18 D6 Data Bit 6Ground Ground J7.19 J7.20 D7 Data Bit 7Ground Ground J7.21 J7.22 D8 Data Bit 8Ground Ground J7.23 J7.24 D9 Data Bit 9Ground Ground J7.25 J7.26 D10 Data Bit 10

6ADS8472EVM SLAU203 – February 2007Submit Documentation Feedback

5 Power Supplies

www.ti.com

Power Supplies

Table 6. TSW1100 Connector (continued)

Description Signal Name Connector.Pin# Signal Name Description

Ground Ground J7.27 J7.28 D11 Data Bit 11Ground Ground J7.29 J7.30 D12 Data Bit 12Ground Ground J7.31 J7.32 D13 Data Bit 13Ground Ground J7.33 J7.34 D14 Data Bit 14Ground Ground J7.35 J7.36 D15 Data Bit 15Ground Ground J7.37 J7.38 N/C Not ConnectedGround Ground J7.39 J7.40 INTc Trigger Clock

This evaluation module provides direct access to all the analog-to-digital converter input control and outputsignals via connector J6, see Table 6 .

Table 7. Pin out for Converter Control Connector, J6

Description Signal Name Connector.Pin# Signal Name Description

Chip Select Signal CS J6.1 J6.2 GND GroundRead Signal RD J6.3 J6.4 GND GroundConvert Start Signal CONVST J6.5 J6.6 GND GroundByte Signal BYTE J6.7 J6.8 GND GroundRESERVED RESERVED J6.9 J6.10 GND GroundBusy Signal BUSY J6.11 J6.12 GND Ground

The EVM accepts four power supplies.•A dual ±VA DC supply for the dual supply op-amps. Recommend ±6VDC supply.•A single +5.0 V DC supply for analog section of the board (A/D + Reference).•A single +5.0V or +3.3V DC supply for digital section of the board (A/D + address decoder + buffers).

There are two ways to provide these voltages.1. Wire in the voltages at test points on the EVM. See Table 8 .

Table 8. Power Supply Test Points

Test Point Signal Description

TP6 +BVDD Apply +3.3VDC or +5.0VDC. See ADC datasheet for full range.TP3 +AVCC Apply +5.0VDC.TP4 +VA Apply +6.0VDC. Positive supply for amplifier.TP5 –VA Apply -6.0VDC. Negative supply for amplifier.

2. Use the power connector J5, and derive the voltages elsewhere. The pinout for this connector isshown in Table 9 . If using this connector, then set W1 jumper to connect +3.3VD or +5VD fromconnector to +BVDD. Short between pins 1-2 to select +5VD, or short between pins 2-3 to select+3.3VD as the source for the digital buffer voltage supply (+BVDD).

Table 9. Power Connector, J5, Pin Out

Signal Power Connector – J5 Signal

+VA(+6V) 1 2 –VA (-6V)+5VA 3 4 N/CDGND 5 6 AGNDN/C 7 8 N/C+3.3VD 9 10 +5VD

SLAU203 – February 2007 ADS8472EVM 7Submit Documentation Feedback

6 Using the ADS8472EVM

6.1 As a Reference Board

6.2 As a Prototype Board

6.2.1 Evaluation Board

6.2.2 EVM and TSW1100 Capture Card

Using the ADS8472EVM

www.ti.com

The ADS8472EVM serves the functions of being a reference design, a prototyping board, and finally as ansoftware test platform.

As a reference design, the ADS8472EVM contains the essential circuitry to showcase the analog-to-digitalconverter. This essential circuitry includes the input amplifier, reference circuit, and buffers. TheADS8472EVM analog input circuit is optimized for a wide bandwidth signal; therefore, the user may needto adjust the input buffer circuitry to better suit your needs. In AC-type applications where signal distortionis a concern, the user should use high quality capacitors such as Mica, polypropylene or COGs typecapacitors in the signal path. In applications where the input is multiplexed, the A/D input resistor andcapacitor may need to be adjusted further.

As a prototype board, the ADS8472EVM features amplifiers in a standard 8-pin SOIC package and manyresistor pads scattered around allowing the user to experiment with a host of circuits, as needed. TheADS8472EVM can be used to evaluate both dual- and single-supply amplifiers in both inverting andnon-inverting configurations. The ADS8472EVM comes installed with a dual-supply amplifier which allowsthe user to take advantage of the full input voltage range of the converter. For applications that requiresignal supply operation and smaller input voltage range, the THS4031 can be replaced with thesingle-supply amplifier like the OPA300 or OPA350. Pad jumper SJP3 should be shorted between pads 1and 2. This shorts the minus supply pin of the amplifier to ground. Positive supply voltage can be appliedat test point TP4 or at connector J5 pin 1.

There are two common methods to evaluate the ADS8472EVM’s performance.1. EVM used as a stand-alone system. The user is responsible for capturing and analyzing the data,typically via a logic analyzer and analysis software (LABView, MATLAB, etc)2. EVM used in conjunction with TI’s TSW1100 data capture card,http://focus.ti.com/docs/toolsw/folders/print/tsw1100.html

The following section discusses method two.

The User’s Guide for the data capture card is available at http://focus.ti.com/lit/ug/slau155a/slau155a.pdf .Refer to this guide for detailed information and set-up instructions.

The ADS8472EVM mates with the TSW1100 card via J7. There are two data ports available on thecapture card, the reference designators are J1 and J2. The ADS8472EVM can be plugged into either port.

The TSW1100 is a data capture card and provides no control signals to the ADS8472. The ADS8472requires a CONVST pulse to begin digitizing the signal. Therefore, the user must provide a CONVST tothe ADS8472 at P3 pin 17 or at J6 pin 5 on the ADS8472EVM. In this case, it is recommended theADS8472 be operated in the CS and RD tied low mode, as this requires only CONVST to toggle. To shortthis signals to ground, simply short across pins 1 and 2, and 3 and 4 of J6, respectively. The digitized datais available on the data bus at the end of every busy cycle. In this operating scheme, the inverted BUSYsignal is used to trigger the TSW1100 card to read the data bus. To avoid line contention remove jumpersfrom W3, W4, W5, and W6 on the ADS8472EVM.

The ADS8472 EVM is supported with the TSW1100 capture card firmware release 1.x. Please use theADS1610EVM entry as a template for acquiring data from the ADS8374EVM. Due to hardware limitationson the TSW1100 platform, data capture from the ADS8472EVM is restricted to 1MSPS minimum.

ADS8472EVM 8 SLAU203 – February 2007Submit Documentation Feedback

6.3 As a Software Test Platform

www.ti.com

Using the ADS8472EVM

As a software test platform, connectors P1, P2, and P3 plug into the parallel interface connectors of the5-6K interface board. The 5-6K interface board sits on the C5000 and C6000 digital signal processorstarter kits (DSK). The ADS8472EVM is mapped then into the processor’s memory space. The 5-6kinterface board also provides an area for signal conditioning. This area can be used to install applicationcircuit(s) for digitization by the ADS8472 analog-to-digital converter. For more information, see the 5-6KInterface Board user’s guide (SLAU104 ) .

For the software engineer, the ADS8472EVM provides a simple platform for interfacing to the converter.The EVM provides standard 0.1-inch headers and sockets to wire into prototype boards. The user needonly provide three address lines (A2, A1, and A0) and address valid line ( DC_CS) to connector P3. Toselect which address combinations generate RD and CONVST, set jumpers as shown in Table 3. Recallthat the Chip Select ( CS) signal is not memory-mapped; therefore, it must be controlled by ageneral-purpose pin or shorted to ground at J6 pin 1. If address decoding is not required, the EVMprovides direct access to converter data bus by P3 and control by J6.

SLAU203 – February 2007 ADS8472EVM 9Submit Documentation Feedback

7 ADS8472EVM BoM

ADS8472EVM BoM

www.ti.com

The following table contains a complete Bill of Materials for the ADS8472EVM. The schematic diagram isalso provided for reference. Contact the Product Information Center or e-mail [email protected]for questions regarding this EVM.

Table 10. Bill of MaterialsQTY Value REF DES Footprint MFG MFG Part No. Description

3 0 R16 R17 R33 603 Panasonic – ERJ-3GEY0R00V RES 0 Ω1/16W 5% 0603 SMDECG orAlternate

2 0 R19 R22 805 Panasonic – ERJ-6GEY0R00V RES 0.0 Ω1/10W 5% 0805 SMDECG orAlternate

2 5.1 R39 R40 805 Panasonic – ERJ-6GEYJ5R1V Resistor 5.1 Ω1/8W 5% 0805ECG orAlternate

3 33 R5 R25 R26 603 Yageo America 9C06031A33R0FKHFT RES 33.0 Ω1/10W 1% 0603 SMDor Alternate

3 49.9 R1–R3 603 Panasonic - ERJ-3EKF49R9V RES 49.9 Ω1/10W 1% 0603 SMDECG orAlternate

2 75 R36 R38 805 Yageo America 9C08052A75R0FKHFT RES 75.0 Ω1/8W 1% 0805 SMDor Alternate

3 300 R4 R27 R29 603 Yageo America RC0603FR-07300RL RES 300 Ω1/10W 1% 0603 SMDor Alternate

4 1k R8 R21 R31 805 Yageo America 9C08052A1001JLHFT RES 1.0k Ω1/8W 5% 0805 SMDR37 or Alternate

5 10k R41–R45 603 Panasonic - ERJ-3EKF1002V RES 10.0k Ω1/10W 1% 0603 SMDECG orAlternate

1 10k R46 805 Panasonic - ERJ-6GEYJ103V RES 10k Ω1/8W 5% 0805 SMDECG orAlternate

2 NI R6 R28 603 Not Installed Not Installed

11 NI R7 R9–R13 805 Not Installed Not InstalledR18 R20 R32R34 R35

2 47 RP1 RP2 CTS_742 CTS 742C163470JTR RES ARRAY 47 Ω16TERM 8RES SMDCorporation

1 1K RP3 CTS_742 CTS 742C163102JTR RES ARRAY 1k Ω16TERM 8RES SMDCorporation

1 51 RP4 CTS_742_4RES CTS 742C083510JTR RES ARRAY 51 Ω8TERM 4RES SMDCorporation

1 10K R24 BOURNS_3296Y Bourns Inc. 3296Y-1-103 POT 10k Ω3/8" SQ CERM SL MT

4 MMZ2012 L1–L4 805 TDK MMZ2012R601A FERRITE CHIP 600 Ω500MA 0805R601A Corporation

13 1000pF C28–C36 603 TDK C1608X7R1H102K CAP CER 1000pF 50V XR7 10% 0603C62–C65 Corporation orAlternate

1 2200pF C45 603 TDK C1608C0G1H222J CAP CER 2200pF 50V C0G 5% 0603Corporation orAlternate

6 0.1 µF C66–C71 603 TDK C1608X7R1E104K CAP CER 0.10 µF 25V X7R 10% 0603Corporation orAlternate

6 0.1 µF C9–C14 805 TDK C2012X7R1H104K CAP CER 0.10 µF 50V X7R 10% 0805Corporation orAlternate

2 0.47 µF C1 C2 603 TDK C1608X5R1A474K CAP CER 0.47 µF 10V X5R 10% 0603Corporation orAlternate

2 1 µF C5 C7 603 TDK C1608X5R1A105KT CAP CER 1.0 µF 10V X5R 10% 0603Corporation orAlternate

10 ADS8472EVM SLAU203 – February 2007Submit Documentation Feedback

Inhaltsverzeichnis

Andere Texas Instruments Hauptplatine Handbücher

Texas Instruments

Texas Instruments bq4050EVM-561 Bedienungsanleitung

Texas Instruments

Texas Instruments ADC32RF-EVM Series Bedienungsanleitung

Texas Instruments

Texas Instruments DAC8534 Bedienungsanleitung

Texas Instruments

Texas Instruments AIC111EVM Bedienungsanleitung

Texas Instruments

Texas Instruments SC70 DAC EVM Bedienungsanleitung

Texas Instruments

Texas Instruments TPS26600-02EVM Bedienungsanleitung

Texas Instruments

Texas Instruments UCD3138OL40EVM-032 Bedienungsanleitung

Texas Instruments

Texas Instruments ADS5292 Bedienungsanleitung

Texas Instruments

Texas Instruments TPS51125AEVM Bedienungsanleitung

Texas Instruments

Texas Instruments DAC 1401 Series Bedienungsanleitung

Texas Instruments

Texas Instruments TPS51113 Bedienungsanleitung

Texas Instruments

Texas Instruments DLP LightCrafter Dual DLPC900 Bedienungsanleitung

Texas Instruments

Texas Instruments LM61460EVM Bedienungsanleitung

Texas Instruments

Texas Instruments TPS652353 Bedienungsanleitung

Texas Instruments

Texas Instruments CC2530EMK Bedienungsanleitung

Texas Instruments

Texas Instruments TPS8269 EVM-207 Series Bedienungsanleitung

Texas Instruments

Texas Instruments TUSB2136 Bedienungsanleitung

Texas Instruments

Texas Instruments AFE5816 Bedienungsanleitung

Texas Instruments

Texas Instruments TPS92520EVM-133 Bedienungsanleitung

Texas Instruments

Texas Instruments TPS549D22EVM-784 Bedienungsanleitung

Texas Instruments

Texas Instruments ADC1 D (RF )RB Series Bedienungsanleitung

Texas Instruments

Texas Instruments Chipcon CC2400DBK Bedienungsanleitung

Texas Instruments

Texas Instruments ADS5294 Bedienungsanleitung

Texas Instruments

Texas Instruments INA301EVM Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung