Texas Instruments DLP LightCrafter 4500 Betriebsanleitung

DLPU017B–March 2014–Revised February 2018

DLP®LightCrafter™ 4500 Flash Programming Guide

Programmer's Guide

DLPU017B–March 2014–Revised February 2018

DLP®LightCrafter™ 4500 Flash Programming Guide

This flash programming guide provides instructions on how to create a JTAG cable and use the flash

programming tool to install the DLPR350 firmware on the DLP LightCrafter 4500.

Contents

1 Overview...................................................................................................................... 2

2 Software Installation......................................................................................................... 2

3 JTAG Boundary Scan Cable ............................................................................................... 3

4 Flash Programming Procedure ............................................................................................ 4

5 Troubleshooting ............................................................................................................ 18

List of Figures

1 UM232H to Molex 51021-0600 Connections ............................................................................ 3

2 J30 Location on the DLP LightCrafter 4500.............................................................................. 4

3 J30 Populated on the DLP LightCrafter 4500............................................................................ 4

4 Power Supply Connected to the DLP LightCrafter 4500 ............................................................... 5

5 JTAG Cable Connected to the DLP LightCrafter 4500 ................................................................. 5

6 JTAG Flash Programmer First Run ....................................................................................... 6

7 Board File Selection in Flash Programmer Tool......................................................................... 7

8 Firmware File Selection in Flash Programmer Tool..................................................................... 8

9 Firmware File Size Selection in Flash Programmer Tool............................................................... 9

10 JTAG Chain Detection in Flash Programmer Tool..................................................................... 10

11 Erase Button in Flash Programmer Tool................................................................................ 11

12 Flash Memory Block Selection and Erase Button ..................................................................... 12

13 Flash Memory Block Erase Completed and Exit Button .............................................................. 13

14 Program Button in Flash Programming Tool ........................................................................... 14

15 Power and JTAG Cable Removed from the DLP LightCrafter 4500 ................................................ 15

16 LightCrafter 4500 GUI Firmware Upload Window ..................................................................... 16

17 Starting The LightCrafter 4500 Firmware File Upload Process ...................................................... 17

List of Tables

1 Required Pin Connections.................................................................................................. 3

Trademarks

LightCrafter is a trademark of Texas Instruments.

DLP is a registered trademark of Texas Instruments.

FTDI Chip is a registered trademark of Future Technology Devices International Ltd.

Windows, Visual C++ are registered trademarks of Microsoft Corporation.

Molex is a registered trademark of Molex.

Overview

www.ti.com

2DLPU017B–March 2014–Revised February 2018

Submit Documentation Feedback

DLP®LightCrafter™ 4500 Flash Programming Guide

1 Overview

The DLP LightCrafter 4500 contains firmware, stored in flash memory, to initialize the onboard DLPC350

controller. If the firmware is compromised, or a blank flash memory module is installed, the memory must

be programmed with the DLPR350 firmware. Without the firmware loaded, the DLPC350 cannot boot up

or initialize the onboard USB port. The user must have access to the USB port to control the device using

the DLP LightCrafter 4500 GUI.

1.1 System Requirements

The following list shows the minimum recommended system requirements for the DLP LightCrafter 4500

flash programming tool:

• PC with 1.4-GHz Pentium IV CPU or higher

• Windows®XP SP3 or higher

• Microsoft Visual C++®2005 Redistributable

• Microsoft Visual C++ 2008 Redistributable

• 512 MB of RAM

• 20 MB of free hard-disk space

• USB port

1.2 Hardware Requirements

The user must create a JTAG boundary scan cable as described in Section 3. The cable requires a

UM232H USB-to-serial adapter board that can be found on the FTDI Chip®development modules page.

The cable also requires a Molex®51021-0600 connector that can be found on the Molex connector

website.

A single 2-mm jumper is required during the flashing process. The jumper is not consumed.

2 Software Installation

2.1 DLP LightCrafter 4500 Flash Programmer And GUI Installation

Download the flash programming tool from the tool page. Extract the executable file from the downloaded

JTAGFlashProgrammer_v***.zip file and run it. Follow the on-screen prompts and select a convenient

installation path for the program. The installer creates a shortcut to the tool in the start menu and on the

desktop.

Download the LightCrafter 4500 GUI from the same tool page as above. Extract the executable file from

the downloaded DLPLCR45000GUI-*.*.*-windows-installer.zip file and run it. Follow the on-screen prompts

and select a convenient installation path for the program. The installer creates a shortcut to the tool in the

start menu and on the desktop.

2.2 DLP LightCrafter 4500 Firmware Installation

Download the latest DLPR350 firmware version from the tool page. Extract the executable file from the

downloaded DLPLCR4500GUI-***-********.zip file and run it. Follow the on-screen prompts and select a

convenient installation path for the files. TI recommends using the default installation path.

2.3 Communication Interface Driver Installation

When using the DLP LightCrafter 4500 flash programming tool, the user must have a communication link

established between the DLP LightCrafter 4500 and the computer running the tool. This allows the user to

read and write to the flash memory from the computer. This connection is established through the JTAG

cable created following this guide. The user needs to install device drivers for the USB-to-serial adapters

from the FTDI Chip website. Choose and install the driver specific to the operating system on the

computer.

www.ti.com

JTAG Boundary Scan Cable

DLPU017B–March 2014–Revised February 2018

DLP®LightCrafter™ 4500 Flash Programming Guide

3 JTAG Boundary Scan Cable

The UM232H USB-to-serial adapter must be connected to the JTAG port on the DLP LightCrafter 4500.

Connecting the two devices requires the use of a Molex 51021-0600 connector. The user can either

directly connect the header pins on the UM232H to the cable or create a board to host the UM232H. The

required pin connections are shown in Table 1 and Figure 1.

NOTE: Two separate pairs of pins must be connected together to supply power to the UM232H from

the computer's USB port.

Table 1. Required Pin Connections

UM232H-J2 Molex 51021-0600

6 6

7 5

8 2

9 4

10 3

11 1

Figure 1. UM232H to Molex 51021-0600 Connections

Flash Programming Procedure

www.ti.com

4DLPU017B–March 2014–Revised February 2018

Submit Documentation Feedback

DLP®LightCrafter™ 4500 Flash Programming Guide

4 Flash Programming Procedure

Populate J30 with a 2-mm jumper on the DLP LightCrafter 4500, as shown in Figure 2 and Figure 3.

Figure 2. J30 Location on the DLP LightCrafter 4500

Figure 3. J30 Populated on the DLP LightCrafter 4500

www.ti.com

Flash Programming Procedure

DLPU017B–March 2014–Revised February 2018

DLP®LightCrafter™ 4500 Flash Programming Guide

Connect the appropriate power supply to the DLP LightCrafter 4500, as shown in Figure 4. The fan on the

rear of the device turns on indicating the board is powered.

Figure 4. Power Supply Connected to the DLP LightCrafter 4500

Connect the JTAG cable to J25, located on the bottom side of the DLP LightCrafter 4500 board. Connect

the UM232H to the computer with an appropriate USB cable, as shown in Figure 5.

Figure 5. JTAG Cable Connected to the DLP LightCrafter 4500

Flash Programming Procedure

www.ti.com

6DLPU017B–March 2014–Revised February 2018

Submit Documentation Feedback

DLP®LightCrafter™ 4500 Flash Programming Guide

Start the flash programmer tool, FlashProgrammer.exe, as shown in Figure 6. Ignore any error messages

about a missing board file for now.

Figure 6. JTAG Flash Programmer First Run

www.ti.com

Flash Programming Procedure

DLPU017B–March 2014–Revised February 2018

DLP®LightCrafter™ 4500 Flash Programming Guide

Click the Browse button next to the board file path. Select the board file called BoardFile.brd that installed

in the flash programmer software tool folder. Figure 7 shows the Browse button and the selected board

file path.

Figure 7. Board File Selection in Flash Programmer Tool

Flash Programming Procedure

www.ti.com

8DLPU017B–March 2014–Revised February 2018

Submit Documentation Feedback

DLP®LightCrafter™ 4500 Flash Programming Guide

Click the Browse button next to the flash image path. Select the flash image called

DLPR350PROM_v****.bin that installed in the DLP LightCrafter 4500 firmware installation folder. Figure 8

shows the button and path.

NOTE: The third box (shown in Figure 8) does not need to be populated.

Figure 8. Firmware File Selection in Flash Programmer Tool

www.ti.com

Flash Programming Procedure

DLPU017B–March 2014–Revised February 2018

DLP®LightCrafter™ 4500 Flash Programming Guide

Set the size of the image to 0x0020000, as in Figure 9.

Figure 9. Firmware File Size Selection in Flash Programmer Tool

Flash Programming Procedure

www.ti.com

10 DLPU017B–March 2014–Revised February 2018

Submit Documentation Feedback

DLP®LightCrafter™ 4500 Flash Programming Guide

Click the Detect Chain button in the upper left-hand corner of the tool. The Detect Chain button is

indicated with a red box in Figure 10.

Figure 10. JTAG Chain Detection in Flash Programmer Tool

Andere Handbücher für DLP LightCrafter 4500

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Texas Instruments Hauptplatine Handbücher

Texas Instruments

Texas Instruments TPS54386EVM Bedienungsanleitung

Texas Instruments

Texas Instruments TPS61230EVM-089 Bedienungsanleitung

Texas Instruments

Texas Instruments TAS5121 Bedienungsanleitung

Texas Instruments

Texas Instruments PFCLLCSREVM034 Bedienungsanleitung

Texas Instruments

Texas Instruments LMK04832SEPEVM Bedienungsanleitung

Texas Instruments

Texas Instruments TPS562231EVM Bedienungsanleitung

Texas Instruments

Texas Instruments LM63635DNEVM Bedienungsanleitung

Texas Instruments

Texas Instruments XWRL1432BOOST Bedienungsanleitung

Texas Instruments

Texas Instruments LMP91051EVM Bedienungsanleitung

Texas Instruments

Texas Instruments MSP430i2040 Bedienungsanleitung

Texas Instruments

Texas Instruments TPS26620-23 Bedienungsanleitung

Texas Instruments

Texas Instruments TSW3000 Bedienungsanleitung

Texas Instruments

Texas Instruments LM36923HEVM Bedienungsanleitung

Texas Instruments

Texas Instruments AM438x ePOS EVM Bedienungsanleitung

Texas Instruments

Texas Instruments DRV8873 EVM Series Bedienungsanleitung

Texas Instruments

Texas Instruments PS62510EVM-168 Bedienungsanleitung

Texas Instruments

Texas Instruments TPS7A89 Bedienungsanleitung

Texas Instruments

Texas Instruments TPS40074EVM-001 Bedienungsanleitung

Texas Instruments

Texas Instruments TPS1H000-Q1 EVM Bedienungsanleitung

Texas Instruments

Texas Instruments ADS1x48EVM Bedienungsanleitung

Texas Instruments

Texas Instruments BOOSTXL-TPS65218 Bedienungsanleitung

Texas Instruments

Texas Instruments DRA72 Series Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8353EVM-PDK Bedienungsanleitung

Texas Instruments

Texas Instruments TPS51220EVM Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung