Texas Instruments TPS281C100 Bedienungsanleitung
EVM User's Guide: TPS281C100EVM
TPS281C100 Evaluation Module
Description
The TPS281C100EVM is a hardware evaluation
module (EVM) used to enable hardware engineers
to evaluate the full performance and functionality of
the TPS281C100 industrial high side switch. The
TPS281C100EVM contains everything needed to test
and assess the TPS281C100 before designing into
part of a greater application's power system. The
evaluation module is designed to either be used as a
standalone board with an attached voltage supply and
output load or in conjunction with an underlying Texas
Instruments microcontroller by using the standardized
BoosterPack™ plug-in module headers. A wide range
of application features such as digital output module,
safe torque off (STO), and holding brake are enabled
and visible through use of this evaluation module.
This EVM is populated with the QFN version of
TPS281C100.
Features
• Configurable current limit with fixed resistors
• Configurable current sense with fixed resistor
• BoosterPack plug-in module headers allowing
power switch to be controlled by external
microcontroller
• On-board 3.3-V LDO allowing for control signals to
be manipulated by a set of jumpers
• Good board layout and copper area for thermal
performance
• Jumper at the output to support different clamp
configurations for inductive discharge
• Optional footprint to populate TVS diode for VDS
clamp for faster inductive discharge
www.ti.com Description
SLVUCR4 – DECEMBER 2023
Submit Document Feedback
TPS281C100 Evaluation Module 1
Copyright © 2023 Texas Instruments Incorporated
1 Evaluation Module Overview
1.1 Introduction
The Texas Instruments TPS281C100EVM is an evaluation module that is used to demonstrate and showcase
all of the features of the underlying TPS281C100 industrial high side switch. This evaluation board provides
a seamless way to connect a set of power supplies to the inputs of the TPS281C100, connect loads to the
output channels, and switch on and off the device using the control pins of the chip itself. An on-board 3.3-V
LDO is included on the EVM to simplify controlling signals to the TPS281C100 and easily assert and deassert
logic signals by the use of a set of external hardware jumpers. Additionally, this EVM includes BoosterPack
plug-in module headers allowing the user to easily connect the TPS281C100 high side switch to an underlying
microcontroller and write software to control and configure the device.
1.2 Kit Contents
Table 1-1 lists the contents of the EVM kit. Contact the Texas Instruments Product Information Center nearest if
any component is missing.
Table 1-1. Kit Contents
Item Quantity
TPS281C100EVM 1
1.3 Specification
The TPS281C100EVM is compatible with both the TPS281C100A and TPS281C100B device versions. Table
1-2 shows the comparison across different device versions. Please note the TPS281C100EVM supports both
versions, but has TPS281C100A populated. To evaluate the TPS281C100B, the TPS281C100A (U2) device has
to be removed and the TPS281C100B device soldered down. Please refer to the device data sheet for more
detailed specifications.
Table 1-2. Device Comparison
DEVICE VERSION PART NUMBER CURRENT LIMIT RANGE INTEGRATED CLAMP
FOR INDUCTIVE LOADS
INRUSH CURRENT
PERIOD
A TPS281C100A 1 A to 5 A (fixed 0.5A with
ILIM short to GND) Yes Yes
B TPS281C100B 1 A to 5 A (fixed 0.5A with
ILIM short to GND) Yes No
1.4 Device Information
The TPS281C100 is a single channel smart high-side switch designed to meet the requirements of industrial
control systems. The low RON(100 mΩ) minimizes device power dissipation, driving a wide range of output load
current up to 4.5-A DC and the 60-V DC operation range improves system robustness.
The TPS281C100 device integrates protection features such as thermal shut down, output clamp, and current
limit. These features improve system robustness during fault events such as short circuit. TPS281C100
implements an adjustable current limiting circuit that improves the reliability of the system by reducing inrush
current when driving large capacitive loads and minimizing overload current. To drive high inrush current loads
such as lamps or fast charging capacitive loads, TPS281C100 implements an inrush current time period with a
higher level of allowed current.
The device also provides an accurate load current sense that allows for improved load diagnostics such as
overload and open-load detection enabling better predictive maintenance.
Table 1-3. Device Information
Part Number Package Body Size (nom)
TPS281C100A QFN (12) 4 mm × 4 mm
Evaluation Module Overview www.ti.com
2TPS281C100 Evaluation Module SLVUCR4 – DECEMBER 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
2 Hardware
2.1 BoosterPack™ Plug-in Module Operation
While the TPS281C100EVM can be used as a standalone evaluation board without the need of any external
microcontroller, the EVM also comes populated with BoosterPack plug-in module headers (J15, J16) to enable
easy interface with a Texas Instruments microcontroller. Additionally, by populating jumper J14 the user has
the ability to power the underlying LaunchPad™ development kit through the integrated 3.3-V LDO on the
TPS281C100EVM. A list of pins connected to the BoosterPack plug-in module header can be seen below in
Table 2-1:
Table 2-1. Connected BoosterPack Plug-in Module Header Pins on TPS281C100EVM
BoosterPack Plug-in
Module Pin Function Note
1 3.3-V power rail Disconnect J14 if powering LaunchPad development kit
through USB.
5 FLT pin used to detect faults Open drain input. Pullup source can be controlled using
jumper J12.
6 Current sense output from IC Current sense resistor is R12
38 Configure DIAG_EN Make sure J7 is not populated if using microcontroller output.
39 Configure EN_IC Make sure J6 is not populated if using microcontroller output.
40 Configure OL_IC Make sure J8 is not populated if using microcontroller output.
Note that for all IO and analog signals being attached to the BoosterPack plug-in module, the relevant 10-kΩ
protection resistors are populated in series with the pin for reverse current protection.
To power the attached LaunchPad development kit from the on-board LDO of the TPS281C100EVM, connect
the jumper J14. Note that this feeds the output of the 3.3-V LDO on the TPS281C100EVM into the 3.3-V rail on
the LaunchPad development kit . If there is another power supply trying to power the LaunchPad development
kit (such as the integrated USB power on the LaunchPad development kit itself), this can potentially cause
issues with the separate power sources fighting for contention.
Jumpers J6 through J8 are used to manually configure the control signals going into the TPS281C100.
When using a microcontroller to control these signals, these jumpers must be unpopulated to allow for the
microcontroller to drive them high or low.
For correct and accurate current sense, the maximum voltage out on the SNS pin is clamped to VSNSFH
internally, so there is no need for external clamp.
2.2 Connection Descriptions
Table 2-2 shows the test points populated on the board as well as the signal connectors.
Table 2-2. Connections and Test Points
Connector and Test Point Description
J1, TP1 Supply voltage VS
J3, TP2 Output voltage VOUT
J2, J4, TP7-TP10 System GND
TP3 ENABLE test point
TP4 DIAG_EN test point
TP5 ILIM test point
TP6 OL_ON test point
TP11 GND_IC test point
TP12 FAULT test point
TP13 SNS_IC test point
www.ti.com Hardware
SLVUCR4 – DECEMBER 2023
Submit Document Feedback
TPS281C100 Evaluation Module 3
Copyright © 2023 Texas Instruments Incorporated
Table 2-3 shows the relevant configuration jumpers of the TPS281C100EVM as well as the associated values.
Please refer to the TPS281C100 data sheet for detailed information on each pin's functionality.
Please note that a white mark on the jumper silkscreen is reflecting the position 1 of the jumper.
Table 2-3. Jumper Configurations
Jumper Function, Settings
J5 Connect 1 and 2 to disable on-board LDO; connect 2 and 3 to enable on-board LDO.
J6 Connect 1 and 2 to pull ENABLE high using the on-board LDO; connect 2 and 3 to pull ENABLE low.
J7 Connect 1 and 2 to pull DIAG_EN high; connect 2 and 3 to pull DIAG_EN low.
J8 Connect 1 and 2 to pull OL_ON high; connect 2 and 3 to pull OL_ON low.
J9 Connect to keep output at 0 V during inductive turn-off; disconnect for TVS clamp to clamp the output
(default to –10 V) during inductive turn-off.
J10 Connect the 24.9 kΩ resistor to ILIM pin. Resistor is paralleled if J11 is also connected.
J11 Connect the 16.9 kΩ resistor to ILIM pin. Resistor is paralleled if J10 is also connected.
J12 Connect 1 and 2 to use LDO for FAULT pullup; connect 2 and 3 to use BoosterPack plug-in module 3.3 V
for FAULT pullup.
J13 Connect to bypass GND network. Disconnect to use GND network.
J14 Connect to power the BoosterPack plug-in module with LDO.
2.3 Best Practices
CAUTION
Hot surface. Contact can cause burns. Do not touch!
Hardware www.ti.com
4TPS281C100 Evaluation Module SLVUCR4 – DECEMBER 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
3.3 Bill of Materials
The table below lists the TPS281C100 Bill of Materials.
Table 3-1. TPS281C100 Bill of Materials
Designator Description Part Number Manufacturer
C1 CAP, CERM, 1 uF, 100 V, +/- 10%, X7S, AEC-Q200 Grade 1, 0805 CGA4J3X7S2A105K125AB TDK
C2 CAP, CERM, 2.2 uF, 50 V, +/- 10%, X7R, AEC-Q200 Grade 1, 0805 CGA4J3X7R1H225K125AB TDK
C3 10 µF ±10% 100 V Ceramic Capacitor X6S 1206 (3216 Metric) C3216X6S2A106K160AC TDK
C4 CAP, CERM, 4700 pF, 100 V, +/- 5%, C0G/NP0, 0603 C0603C472J1GAC7867 Kemet
C5 CAP, CERM, 0.022 uF, 100 V, +/- 10%, X7R, 0603 C1608X7R2A223K080AA TDK
C8 CAP, CERM, 1000 pF, 50 V, +/- 5%, X7R, AEC-Q200 Grade 1, 0603 C0603C102J5RACAUTO Kemet
C9 CAP, CERM, 0.1 uF, 100 V, +/- 10%, X7R, AEC-Q200 Grade 1, 0805 CGA4J2X7R2A104K125AA TDK
D1, D6 Diode, Switching, 200 V, 0.2 A, SOT-23 BAS21-7-F Diodes Inc.
D4 Diode, TVS, Bi, 60 V, 96.8 Vc, SMC (no polarity) SMCJ60CA-HRA Littelfuse
D5 Diode, TVS, Uni, 10 V, SMC SMCJ10A Bourns
J1, J3 BANANA JACK, SOLDER LUG, RED, TH SPC15363 Tenma
J2, J4 BANANA JACK, SOLDER LUG, BLACK, TH SPC15354 Tenma
J5, J6, J7, J8, J12 Header, 2.54mm, 3x1, Gold, TH 961103-6804-AR 3M
J9, J10, J11, J13, J14 Header, 2.54mm, 2x1, TH 961102-6404-AR 3M
J15, J16 Receptacle, 2.54mm, 10x2, Tin, TH SSQ-110-03-T-D Samtec
R1, R2, R3, R10, R11 RES, 10 k, 5%, 0.1 W, 0603 RC0603JR-0710KL Yageo
R5 RES, 0, 5%, 0.1 W, AEC-Q200 Grade 0, 0603 CRCW06030000Z0EA Vishay-Dale
R6 RES, 24.9 k, 0.5%, 0.1 W, 0805 RR1220P-2492-D-M Susumu Co Ltd
R7 RES, 16.9 k, 0.5%, 0.1 W, 0805 RR1220P-1692-D-M Susumu Co Ltd
R8, R9 RES, 1.0 k, 5%, 0.1 W, AEC-Q200 Grade 0, 0603 RCA06031K00JNEA Vishay-Dale
R12 RES, 1.00 k, 1%, 0.25 W, 0805 ERJ-P06F1001V Panasonic
SH-J1, SH-J2, SH-J3, SH-J4,
SH-J5, SH-J6, SH-J7, SH-J8 Shunt, 100mil, Gold plated, Black SNT-100-BK-G Samtec
TP1, TP2 Test Point, Multipurpose, Red, TH 5010 Keystone
TP3, TP4, TP5, TP6, TP12,
TP13 Test Point, Multipurpose, Green, TH 5126 Keystone
TP7, TP8, TP9, TP10, TP11 Test Point, Multipurpose, Black, TH 5011 Keystone
www.ti.com Hardware Design Files
SLVUCR4 – DECEMBER 2023
Submit Document Feedback
TPS281C100 Evaluation Module 9
Copyright © 2023 Texas Instruments Incorporated
Table 3-1. TPS281C100 Bill of Materials (continued)
Designator Description Part Number Manufacturer
U1
Single Output LDO, 100 mA, Fixed 3.3 V Output, 3 to 60 V Input,
with Enable and Power Good, 8-pin MSOP (DGN), -40 to 125 degC,
Green (RoHS & no Sb/Br)
TPS7A1633DGNR Texas Instruments
U2 60-V, 100-mΩ, Single-Channel Smart High-Side Switch TPS281C100DNTR Texas Instruments
Hardware Design Files www.ti.com
10 TPS281C100 Evaluation Module SLVUCR4 – DECEMBER 2023
Submit Document Feedback
Copyright © 2023 Texas Instruments Incorporated
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Texas Instruments Hauptplatine Handbücher
Texas Instruments
Texas Instruments DRV8328A Bedienungsanleitung
Texas Instruments
Texas Instruments DACx0504 series Bedienungsanleitung
Texas Instruments
Texas Instruments MSC1211EVM Bedienungsanleitung
Texas Instruments
Texas Instruments QFN16-DIP-EVM Bedienungsanleitung
Texas Instruments
Texas Instruments DS90UB913A-CXEVM Bedienungsanleitung
Texas Instruments
Texas Instruments PGA411-Q1 EVM Bedienungsanleitung
Texas Instruments
Texas Instruments LM66200EVM Bedienungsanleitung
Texas Instruments
Texas Instruments TAS5766MDCAEVM Bedienungsanleitung
Texas Instruments
Texas Instruments bq24725 Bedienungsanleitung
Texas Instruments
Texas Instruments MCT8314Z Bedienungsanleitung
Texas Instruments
Texas Instruments OMAP35x Bedienungsanleitung
Texas Instruments
Texas Instruments TPD3S716-Q1EVM Bedienungsanleitung
Texas Instruments
Texas Instruments Jacinto 7 Bedienungsanleitung
Texas Instruments
Texas Instruments TAS6424MS-Q1 EVM Bedienungsanleitung
Texas Instruments
Texas Instruments TPS552882EVM-2MHz Bedienungsanleitung
Texas Instruments
Texas Instruments TUSB1042 Bedienungsanleitung
Texas Instruments
Texas Instruments TMP110 Bedienungsanleitung
Texas Instruments
Texas Instruments TCAN1046A/V CAN Bedienungsanleitung
Texas Instruments
Texas Instruments DLP5532HBQ1EVM Bedienungsanleitung
Texas Instruments
Texas Instruments TAS5708EVM Bedienungsanleitung
Beliebte Hauptplatine Handbücher anderer Marken
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Bedienungsanleitung
Gigabyte
Gigabyte GA-9IVDT Bedienungsanleitung
Commell
Commell MS-C73 Bedienungsanleitung
IBT Technologies
IBT Technologies MB860 Bedienungsanleitung
Nvidia
Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung
Biostar
Biostar M7VIT Bravo Bedienungs- und Montageanleitung
