Texas Instruments TPS65986EVM Bedienungsanleitung

SLVUAN9A–June 2016–Revised July 2016

TPS65986 EVM User's Guide

LaunchPad is a trademark of Texas Instruments.

All other trademarks are the property of their respective owners.

User's Guide

SLVUAN9A–June 2016–Revised July 2016

TPS65986 EVM User's Guide

This document is the user's guide for the TPS65986 evaluation module (TPS65986EVM). The

TPS65986EVM allows for evaluation of the TPS65986 device as part of a stand-alone testing kit and for

development and testing of USB Type-C and power-delivery (PD) end products.

ATTENTION

STATIC SENSITIVE DEVICES

HANDLE ONLY AT

STATIC SAFE WORK STATIONS

About this Manual

www.ti.com

2SLVUAN9A–June 2016–Revised July 2016

Submit Documentation Feedback

TPS65986 EVM User's Guide

1 About this Manual

This user's guide describes the TPS65986EVM. The guide consists of an introduction, setup instructions,

the EVM schematic, board layouts, component views, internal power (PWR) and ground (GND) plane

layouts, and a bill of materials (BOM).

2 Information About Cautions and Warnings

CAUTION

This EVM contains components that can potentially be damaged by

electrostatic discharge. Always transport and store the EVM in the supplied

ESD bag when not in use. Handle using an antistatic wristband. Operate on an

antistatic work surface. For more information on proper handling, see

Electrostatic Discharge (ESD).

3 Items Required for Operation

The following items are required to use the TPS65986EVM:

• TPS65986 data sheet (TPS65986 USB Type-C and USB PD Controller and Power Switch)

• TPS65986EVM

• DP-EXPANSION-EVM (DP-EXPANSION-EVM User Guide)

– Testing for DisplayPort, USB data, or both

– Mini DisplayPort to DisplayPort cable

– USB3.0 Standard-A to -B cable

•TotalPhase Aardvark I2C/SPI Host Adapter and USB Standard-B to -A cable

– TPS65986 register access, firmware updating, firmware testing, or a combination of these

– TPS6598x Utilities GUI

• TPS6598x Configuration GUI (www.ti.com/tool/tps6598x-config)

• Barrel-jack adapter or DC power supply

• USB Type-C cable

• USB Type-C to Standard-A cable

4 Introduction

The TPS65986 device is a stand-alone USB Type-C and power-delivery (PD) controller providing cable-

plug and orientation detection at the USB Type-C connector. Upon cable detection, the TPS65986 device

communicates on the CC wire using the USB PD protocol. When cable detection and USB-PD negotiation

are complete, the TPS65986 device enables the appropriate power path and configures alternate mode

settings for internal and (optional) external multiplexers.

This user's guide describes the TPS65986EVM and the capabilities of the EVM with the DP-EXPANSION-

EVM. This guide also contains testing procedures of various PD-power and alternate mode configurations.

The EVM comes with pre-loaded configurations for out of the box functionality and is also customizable

through the TPS6598x Configuration Tool. The TPS65986EVM is a module-based design, allowing the

user to design a custom board to prototype a Type-C PD product using the TPS65986 device. The EVM

has four main connectors which are the Type-C receptacle, barrel-jack power, expansion-board connector,

www.ti.com

Setup

SLVUAN9A–June 2016–Revised July 2016

TPS65986 EVM User's Guide

and two BoosterPack headers. The Type-C receptacle is a full-feature port, with power, SSTX, SSRX,

SBU1, SBU2, DP, and DN signals. The TPS65986 device can be used in self-powered and bus-powered

configurations for added flexibility. When self powered, the EVM can provide up to 60 W of power (20 V, 3

A). The EVM is also capable of sinking 60 W of power (20 V, 3 A) when the device is in powered, dead

battery, or consumer mode. The EVM can perform a power-role swap to provide power when the barrel

jack (external power) is connected. The expansion board connector routes the power, SSTX, SSRX,

USB_RP_P, USB_RP_N, AUX_P, AUX_N, HPD, I2C, and GPIO control for the DP-EXPANSION-EVM.

The BoosterPack headers give access to the GPIO, 3.3-V and 5-V rails, SPI pins, I2C, AUX_P, AUX_N,

USB_RP_P, and USB_RP_N. The BoosterPack headers are configured for mounting on any TI MCU

LaunchPad™ development kit. Custom PCBs may be built as a mechanical interface to the Aardvark if the

I2C, SPI, and GND pins of the BoosterPack headers are wired to the associated pins on a 10-pin male

header to mate with the Aardvark.

5 Setup

This section describes the various EVM features and how to test the various configurations.

5.1 Switch, Push Button, Connector, and Test Point Descriptions

5.1.1 S2 Switch Bank

This switch bank is used to configure the EVM with the pre-loaded firmware. A total of 8 configurations are

set by the state of the switches on S2. The top switch represents bit 0 and the bottom switch represents

bit 3. The left position is low and the right position is high when looking at the EVM with the Type-C

receptacle facing down. Bit 0, bit 1, and bit 2 are used for setting the configuration, and bit 3 is reserved

for future use (should always be set low for now). Bit 0, bit 1, bit 2, and bit 3 are connected to GPIO1,

DEBUG3, DEBUG4, and GPIO5 respectively. The high position is pulled up through an 11-kΩresistor to

LD0_3V3, and GPIO1, DEBUG3, DEBUG4, and GPIO5 are pulled down through a 100-kΩresistor.

5.1.1.1 S2: DisplayPort Pin Assignment C to Pin Assignment D Switch

The TPS65986EVM allows for Configuration ID 0 to toggle between 4-lane DisplayPort, 2-lane

DisplayPort, and USB3.0 Multifunction. The first switch in S2 is used to toggle between configurations and

does not change the configuration that was selected within Table 2. When switched to the right position,

the TPS65986EVM changes the configuration to prefer USB3.0 Multifunction and renegotiates the

DisplayPort alternate mode. When switched back to the left position, the TPS65986EVM changes the

configuration to not prefer USB3.0 Multifunction and renegotiates the DisplayPort alternate mode.

5.1.2 S1 HRESET Push-Button

S1 is located on the top-left corner of the EVM, under the Expansion Board Connector. This switch is a

push-button that pulls the HRESET pin (D6), of the TPS65986 device high when pressed. Releasing the

push-button pulls HRESET low again, and the TPS65986 device goes through a hardware reset, which

consists of reloading firmware from the non-volatile memory of the external flash. When changing a

configuration on S2, S1 can be used to reset the TPS65986 device, which loads the updated

configurations without disconnecting power from the EVM.

5.1.3 J4: Barrel-Jack Power Connector

The barrel-jack power connector accepts a 19-V to 20-V DC supply. A standard Dell or HP notebook

adaptor (or similar adaptor) provides the required power. This input provides the PP_HV power rail with

the 19 V to 20 V for high-power PD contracts up to 60 W. Select an appropriate power-capable adapter of

60-W operation. For example, the 130-W Dell part number 492-BBGP could be used.

Setup

www.ti.com

4SLVUAN9A–June 2016–Revised July 2016

Submit Documentation Feedback

TPS65986 EVM User's Guide

5.1.3.1 Barrel Jack Detect

The TPS65986EVM is capable of requesting a power-role swap when the barrel jack is connected on an

EVM that is currently bus powered which is valid for the configuration IDs that are capable of delivering

power. The barrel jack voltage is sensed by a comparator, which drives GPIO2 on the TPS65986 device.

For enabling barrel jack detect or other GPIOs, refer to TPS6598x Utilities Tool User Guide and

TPS65982 and TPS65986 Firmware User’s Guide.

5.1.4 TP3 and TP4: GND Test Points

Two GND test points are provided for attaching an oscilloscope, multi-meter, or external load GND. These

test points are connected to the board GND planes through 4 vias.

5.1.5 TP1 and TP2: CC1/CC2 Test Points

These test points can be used to tie a PD protocol analyzer for PD BMC data or to verify the BMC signal

integrity with an oscilloscope (depending on the cable orientation). A multi-meter or oscilloscope can be

used to measure VCONN when an electronically marked Type-C cable is connected. These test points

are not intended to provide an external load on VCONN. Figure 1 shows the BMC data oscilloscope

capture.

Figure 1. TPS65986 BMC Data

5.1.6 TP5: VBUS Test Point

The VBUS test point is used to measure VBUS at the connector.

CAUTION

With PD power possibly going up to 20 V, use caution when connecting and

disconnecting probes on the TPS65986EVM. The VBUS test point is capable of

drawing up to 3 A for an external load.

A PD-power contract with the necessary capability must be negotiated to draw current from the VBUS test

point. Refer to TPS6598x Configuration GUI User Guide for configuration instruction. Figure 2 shows the

VBUS voltage during PD power negotiation.

www.ti.com

Setup

SLVUAN9A–June 2016–Revised July 2016

TPS65986 EVM User's Guide

Figure 2. TPS65986 VBUS Voltage Transition

5.1.7 TP6: PP_HV Test Point

This test point is the same power rail as the barrel jack, and it can be used to either provide power to the

TPS65986EVM or measure the voltage supply for the PP_HV. When a custom configuration is created

using the TPS6598x Configuration Tool, the voltage of PP_HV can be set to a minimum of 12 V for high-

voltage contracts. The pre-loaded TPS65986EVM firmware expects to have 20 V at PP_HV (or on barrel

jack) for the configured power capabilities. The PP_HV test point can also be used to sink power when

acting as a consumer or a bus powered device. PP_HV is capable of sinking up to 3 A when acting as a

consumer.

5.1.8 J2 and J3: BoosterPack Headers

These headers allow the EVM to be connected to any TI MCU LaunchPad™ development kit. See

Figure 29 for names of all connections.

NOTE: Some of the header pins are not connected unless a 0-Ωoption resistor is placed.

5.2 LED Indicators Description

The EVM has multiple LEDs to notify the user what type of connection is present. The LEDs are

separated into two groups: mux control LEDs (MXCTL1-3) and status LEDs.

NOTE: The LEDs are enabled through GPIO in the pre-loaded firmware. Therefore, each must be

enabled separately if configuring a custom image (see TPS6598x Configuration GUI User

Guide and TPS65982 and TPS65986 Firmware User’s Guide).

Using the TPS65986EVM

www.ti.com

6SLVUAN9A–June 2016–Revised July 2016

Submit Documentation Feedback

TPS65986 EVM User's Guide

5.2.1 MXCTL1-3 LEDs (Super-Speed Mux Contol LED)

These LEDs correspond to the GPIOs required to drive a super-speed multiplexer for the SSTX and

SSRX signals to a Type-C connector. Table 1 summarizes the LED behavior according to the type of

connection.

Table 1. MXCTLx LED Functions

LED Indicator GPIO Function

MXCTL1 GPIO_0 Plug Present

MXCTL2 GPIO_3 HD3SS460 AMSEL

MXCTL3 GPIO_6 DP Connection

5.2.2 Status LEDs

The status LEDs indicate the cable orientation, the voltage present on VBUS, and the type of connection.

The CC1 and CC2 LEDs indicate the orientation of the Type-C cable (only one of these LEDs turns on at

a time). LED A is on when 5 V is sourced on VBUS and blinks when a high-voltage contract is in place

(when acting as a source or sink of power). LED B indicates if a USB3 connection is present.

6 Using the TPS65986EVM

This section describes the EVM configurations on the pre-loaded firmware, getting started, and debugging

the EVM.

6.1 Powering the TPS65986EVM

The main power supply for the EVM is J1 barrel jack, which accepts 19 V to 20 V through a barrel jack

adaptor. The EVM can also be powered with an external power supply on TP6. The input voltage can

range to 12 V to 20 V, but the appropriate power profile for PP_HV should be configured in the firmware

using the configuration tool. The EVM can also be powered from a TI MCU LaunchPad™ development kit

by placing R30 and R31 with 0-Ωresistors. If powering with a LaunchPad™ development kit, the EVM

does not support high-voltage contracts or provide high currents at 5 V because of the limited power

capability. The EVM can also be bus powered from the Type-C connector and accepts 5 V to 20 V on

VBUS, depending on the sink configuration.

6.2 Firmware Configurations

The EVM is shipped with a preloaded firmware image that supports various Type-C and PD products. The

firmware is loaded at start-up and the configuration is defined by the state of the S2 switch (see

Section 5.1.1). The top three switches in the switch bank represent B0, B1, and B2, respectively (see

Figure 3). The top switch is used for toggling between DisplayPort configurations for 2-lane DP, USB3

multi-function, and 4-lane DP after the configuration in the table has been loaded. Table 2 lists the eight

configurations on the EVM.

Figure 3. S2 Switch Board

www.ti.com

Using the TPS65986EVM

SLVUAN9A–June 2016–Revised July 2016

TPS65986 EVM User's Guide

Table 2. TPS65986EVM Configuration Table

CFG

ID Switch S1 Port Type Type-C

Power PD Source PD Sink

Capabilities DP Support PD Control Response PD Control Application FET Paths Used

Data Power A V at

AV at

AData Role Preferred Power Role Preferred Initiated DR/PR Swaps

■ ← 0

DRP

Rp/Rd 35 at

320 at

3—5 at

0— — UFP_D

Config C and

UFP

DR Swap to DFP - Reject

DR Swap to UFP - Accept

Source

PR Swap to Src - Accept

PR Swap to Snk - Reject

Initiate DR swap to UFP

Initiate PR swap to Src

Self-

powered

docking

system

Source: 5 V at 3-A

PP_5V0

Source: 20 V at 3-A

PP_HV

1→ ■

■ ← 0

DRP

Rp/Rd 35 at

3— — 5 at

12 to

20 at

2—DFP_D

Config C, D

and E

DFP

DR Swap to DFP - Accept

DR Swap to UFP - Reject

Sink

PR Swap to Src - Accept

PR Swap to Snk - Accept

Initiate DR swap to DFP

Initiate PR swap to Snk Notebook

system

Source: 5 V at 3-A

PP_5V0

Sink: PP_HV

■ ← 0

1→ ■

■ ← 0

DRP

Rp/Rd 35 at

320 at

3—5 at

0— — DFP_D

Config C, D

and E

DFP

DR Swap to DFP - Accept

DR Swap to UFP - Reject

Source

PR Swap to Src - Accept

PR Swap to Snk - Reject

Initiate DR swap to DFP

Initiate PR swap to Src Add-in card

Source: 5 V at 3-A

PP_5V0

Source: 20 V at 3-A

PP_HV

1→ ■

■ ← 0

DRP

Rp/Rd 35 at

320 at

3—5 at

0— — — UFP

DR Swap to DFP - Reject

DR Swap to UFP - Accept

Source

PR Swap to Src - Accept

PR Swap to Snk - Reject

Initiate DR swap to UFP

Initiate PR swap to Src Charging

hard drive

Source: 5 V at 3-A

PP_5V0

Source: 20 V at 3-A

PP_HV

■ ← 0

1→ ■

■ ← 0

UFP

Rp/Rd — — — — 5 at

0.9 — — UFP_D

Config C and

UFP

DR Swap to DFP - Reject

DR Swap to UFP - Accept

Sink

PR Swap to Src - Reject

PR Swap to Snk - Accept —Display

dongle Sink: PP_HV

1→ ■

■ ← 0

1→ ■

■ ← 0

DRP

Rp/Rd 35 at

320 at

3—5 at

0.9

12 to

20 at

2—UFP_D

Config C and

UFP

DR Swap to DFP - Reject

DR Swap to UFP - Accept

Source

PR Swap to Src - Accept

PR Swap to Snk - Reject

Initiate DR swap to UFP

Initiate PR swap to Src

Mini-dock

and

multifunction

dongle

Source: 5 V at 3-A

PP_5V0

Source: 20 V at 3-A

PP_HV

Sink: PP_HV

■ ← 0

1→ ■

■ ← 0

DFP

Rp 35 at

320 at

3— — — — — DFP

DR Swap to DFP - Accept

DR Swap to UFP - Reject

Source

PR Swap to Src - Accept

PR Swap to Snk - Reject —DFP only

host

Source: 5 V at 3-A

PP_5V0

Source: 20 V at 3-A

PP_HV

1→ ■

■ ← 0

UFP

Rd — — — — 5 at

312 at

320 at

3—UFP

DR Swap to DFP - Reject

DR Swap to UFP - Accept

Sink

PR Swap to Src - Reject

PR Swap to Snk - Accept —UFP only

host Sink: PP_HV

CFG

ID Switch S1

Port Type Type-C

Power PD Source PD Sink

Capabilities DP Support

PD Control Response PD Control

Application

Data Power V at

V at

AData Role Preferred Power Role Preferred Initiated DR/PR Swaps

FET Paths Used

1→ ■

■ ← 0

DRP

Rp/Rd 35 at

3— — 5 at

12 to

20 at

—

DFP_D

Config C, D

and E

DFP

DR Swap to DFP - Accept

DR Swap to UFP - Reject

Sink

PR Swap to Src - Accept

PR Swap to Snk - Accept

Initiate DR swap to DFP

Initiate PR swap to Snk

Notebook

system

Source: 5 V at 3-A

PP_5V0

Sink: PP_HV

CFG

ID Switch S1

Port Type Type-C

Power PD Source PD Sink

Capabilities DP Support

PD Control Response PD Control

Application

Data Power V at

V at

AData Role Preferred Power Role Preferred

■ ← 0

DRP

Rp/Rd 35 at

20 at

3—5 at

0— —

UFP_D

Config C and

UFP

DR Swap to DFP - Reject

DR Swap to UFP - Accept

Source

PR Swap to Src - Accept

PR Swap to Snk - Reject

Initiate DR swap to UFP

Initiate PR swap to Src

Self-

powered

docking

system

Source: 5 V at 3-A

PP_5V0

Source: 20 V at 3-A

PP_HV

Initiated DR/PR Swaps

FET Paths Used

Using the TPS65986EVM

www.ti.com

8SLVUAN9A–June 2016–Revised July 2016

Submit Documentation Feedback

TPS65986 EVM User's Guide

6.2.1 Configuration ID 0: Self-Powered Docking System

This configuration represents a docking system that is connected to an external source of power. The

configuration is a DRP product that accepts power-role swaps to source and data-role swaps to UFP. The

firmware is also configured to automatically request a power-role swap to source or data-role swap to UFP

when appropriate.

Table 3. Configuration ID 0

6.2.1.1 Power Configurations

This configuration supports sourcing up to 60 W and has two source profiles. This configuration can

provide 5 V at 3 A and 20 V at 3 A through the PP_HV path. This configuration only requests a 5-V at 0 A

contract as a sink because it is a docking system that is externally powered.

6.2.1.2 Data Configurations

This configuration is a UFP in terms of data for USB and DisplayPort functionality. When connected to

another DisplayPort UFP_D product, the DisplayPort alternate mode is not established because two

UFP_D products are connected. The ideal connections are to a DFP_D DisplayPort product or a USB

Host. The DP-EXPANSION-EVM (DisplayPort sink board) allows the user to use the USB and DisplayPort

signals.

6.2.2 Configuration ID 1: Notebook System

This configuration represents a notebook system that is battery powered. The configuration is a DRP

product that accepts power-role swaps to source or sink and data-role swaps to DFP. The firmware is also

configured to automatically request a power-role swap to sink or data-role swap to DFP when appropriate.

This configuration rejects any data-role swaps to UFP because it is a data host.

Table 4. Configuration ID 1

6.2.2.1 Power Configurations

This configuration supports sourcing up to 15 W and has one source profile. This configuration can

provide 5 V at 3 A, and has two sink profiles through the PP_HV path: 5 V at 0 A and 12 V to 20 V at 2 A.

When an appropriate source capability is advertised, it requests a high-voltage contract because the

notebook requires a higher voltage to charge.

6.2.2.2 Data Configurations

This configuration is a DFP in terms of data for USB and DisplayPort functionality. When connected to

another DisplayPort DFP_D product, the DisplayPort alternate mode is not established because of two

DFP_D products being connected. The ideal connections are to a UFP_D DisplayPort product or a USB

device. The DP-EXPANSION-EVM (DisplayPort source board) allows the user to use the USB and

DisplayPort signals into a legacy notebook.

CFG

ID Switch S1

Port Type Type-C

Power PD Source PD Sink

Capabilities DP Support

PD Control Response PD Control

Application

Data Power V at

V at

AData Role Preferred Power Role Preferred Initiated DR/PR Swaps

FET Paths Used

1→ ■

■ ← 0

DRP

Rp/Rd 35 at

20 at

3—5 at

0—

UFP

DR Swap to DFP - Reject

DR Swap to UFP - Accept

Source

PR Swap to Src - Accept

PR Swap to Snk - Reject

Initiate DR swap to UFP

Initiate PR swap to Src

Charging

hard drive

Source: 5 V at 3-A

PP_5V0

Source: 20 V at 3-A

PP_HV

— —

CFG

ID Switch S1

Port Type Type-C

Power PD Source PD Sink

Capabilities DP Support

PD Control Response PD Control

Application

Data Power V at

V at

AData Role Preferred Power Role Preferred Initiated DR/PR Swaps

FET Paths Used

■ ← 0

1→ ■

■ ← 0

DRP

Rp/Rd 35 at

20 at

3—5 at

0— —

DFP_D

Config C, D

and E

DFP

DR Swap to DFP - Accept

DR Swap to UFP - Reject

Source

PR Swap to Src - Accept

PR Swap to Snk - Reject

Initiate DR swap to DFP

Initiate PR swap to Src Add-in card

Source: 5 V at 3-A

PP_5V0

Source: 20 V at 3-A

PP_HV

www.ti.com

Using the TPS65986EVM

SLVUAN9A–June 2016–Revised July 2016

TPS65986 EVM User's Guide

6.2.3 6.2.3 Configuration ID 2: Add-In Card

This configuration represents an add-in card or motherboard host that is self-powered. The configuration is

a DRP product that accepts power-role swaps to source and data-role swaps to DFP. The firmware is also

configured to automatically request a power-role swap to source or data-role swap to DFP when

appropriate. This configuration rejects a data-role swap to UFP because it is a data host.

Table 5. Configuration ID 2

6.2.3.1 Power Configurations

This configuration supports sourcing up to 60 W and has two source profiles. This configuration can

provide 5 V at 3 A and 20 V at 3 A through the PP_HV path. This configuration only requests a 5 V at 0 A

contract because it is an add-in card or motherboard that is externally powered.

6.2.3.2 Data Configurations

This configuration is a DFP in terms of data for USB and DisplayPort functionality. When connected to

another DisplayPort DFP_D product, the DisplayPort alternate mode is not established because two

DFP_D products are connected. The ideal connections are to a UFP_D DisplayPort product or a USB

device. The DP-EXPANSION-EVM (DisplayPort source board) allows the user to route the USB and

DisplayPort signals into a legacy notebook.

6.2.4 Configuration ID 3: Charging Hard Drive

This configuration represents a charging hard drive that is self-powered. The configuration is a DRP

product that accepts power-role swaps to source and data-role swaps to UFP. The firmware is configured

to automatically request a power-role swap to source or data-role swap to DFP when appropriate. The

configuration rejects a data-role swap to DFP because it is a data device.

Table 6. Configuration ID 3

6.2.4.1 Power Configurations

This configuration supports sourcing up to 60 W and has two source profiles. The configuration can

provide 5 V at 3 A and 20 V at 3 A through the PP_HV path. This configuration only requests a 5 V at 0 A

contract because it is a hard drive that is externally powered.

6.2.4.2 Data Configurations

This configuration is a UFP in terms of data for USB data only. The DP-EXPANSION-EVM( DisplayPort

source board) can be used to bring out the USB signals.

CFG

ID Switch S1

Port Type Type-C

Power PD Source PD Sink

Capabilities DP Support

PD Control Response PD Control

Application

Data Power V at

V at

AData Role Preferred Power Role Preferred Initiated DR/PR Swaps

FET Paths Used

1→ ■

■ ← 0

1→ ■

■ ← 0

DRP

Rp/Rd 35 at

20 at

3—5 at

0.9

12 to

20 at

UFP_D

Config C and

UFP

DR Swap to DFP - Reject

DR Swap to UFP - Accept

Source

PR Swap to Src - Accept

PR Swap to Snk - Reject

Initiate DR swap to UFP

Initiate PR swap to Src

Mini-dock

and

multifunction

dongle

Source: 5 V at 3-A

PP_5V0

Source: 20 V at 3-A

PP_HV

Sink: PP_HV

—

CFG

ID Switch S1

Port Type Type-C

Power PD Source PD Sink

Capabilities DP Support

PD Control Response PD Control

Application

Data Power V at

V at

AData Role Preferred Power Role Preferred Initiated DR/PR Swaps

FET Paths Used

■ ← 0

1→ ■

■ ← 0

UFP

Rp/Rd —5 at

0.9

UFP_D

Config C and

UFP

DR Swap to DFP - Reject

DR Swap to UFP - Accept

Sink

PR Swap to Src - Reject

PR Swap to Snk - Accept

—Display

dongle Sink: PP_HV— — — — —

Using the TPS65986EVM

www.ti.com

10 SLVUAN9A–June 2016–Revised July 2016

Submit Documentation Feedback

TPS65986 EVM User's Guide

6.2.5 Configuration ID 4: Display Dongle

This configuration represents a display dongle that is bus-powered only. The configuration is a UFP

product that accepts power-role swaps to sink and data-role swaps to UFP. This configuration rejects a

data-role swap to DFP because it is a data device.

Table 7. Configuration ID 4

6.2.5.1 Power Configurations

This configuration does not support source profiles. It will request a 5-V at 900 mA contract to connect as

a bus powered device to all existing Type-C PD notebooks.

6.2.5.2 Data Configurations

This configuration is a UFP in terms of data for USB and DisplayPort functionality. When connected to

another DisplayPort UFP_D product, the DisplayPort alternate mode is not established because two

UFP_D products are connected. The ideal connections are to a DFP_D DisplayPort product or a USB

host. The DP-EXPANSION-EVM (DisplayPort sink board) can be used to route the USB and DisplayPort

signals.

6.2.6 Configuration ID 5: Mini-Dock or Multifunction Dongle

This configuration represents a mini-docking system or multifunction dongle device that can be self or bus

powered. This configuration is a DRP product that accepts power-role swaps to source and data-role

swaps to UFP. The firmware is also configured to automatically request a power-role swap to source or

data-role swap to UFP when appropriate. The configuration rejects a data-role swaps to DFP because it is

a device.

Table 8. Configuration ID 5

6.2.6.1 Power Configurations

This configuration supports sourcing up to 60 W and has two source profiles. The configuration can

provide 5 V at 3 A and 20 V at 3 A through the PP_HV path. This configuration requests a 5 V at 900 mA

contract to connect as a bus powered device to all existing Type-C PD notebooks.

6.2.6.2 Data Configurations

This configuration is a UFP in terms of data for USB and DisplayPort functionality. When connected to

another DisplayPort UFP_D product, the DisplayPort alternate mode is not established because two

UFP_D products are connected. The ideal connections are to a DFP_D DisplayPort product or a USB

host. The DP-EXPANSION-EVM (DisplayPort sink board) can be used to bring out the USB and

DisplayPort signals.

Inhaltsverzeichnis

Andere Texas Instruments Hauptplatine Handbücher

Texas Instruments

Texas Instruments DRV2605EVM-BT Bedienungsanleitung

Texas Instruments

Texas Instruments TLC5929 Bedienungsanleitung

Texas Instruments

Texas Instruments THS6222RHFEVM Bedienungsanleitung

Texas Instruments

Texas Instruments BQ77207 Bedienungsanleitung

Texas Instruments

Texas Instruments BOOST-LDC3114EVM Bedienungsanleitung

Texas Instruments

Texas Instruments TPD1E05U05-Q1 Bedienungsanleitung

Texas Instruments

Texas Instruments DLP5532HBQ1EVM Bedienungsanleitung

Texas Instruments

Texas Instruments Peripheral Explorer Kit Bedienungsanleitung

Texas Instruments

Texas Instruments RS485-HF-DPLX-EVM Bedienungsanleitung

Texas Instruments

Texas Instruments AMC7834 Bedienungsanleitung

Texas Instruments

Texas Instruments CC3200MODLAUNCHXL Bedienungsanleitung

Texas Instruments

Texas Instruments DRV8316REVM Bedienungsanleitung

Texas Instruments

Texas Instruments TPS62806-7-8EVM083 Bedienungsanleitung

Texas Instruments

Texas Instruments AN-1966 LMH2190 Bedienungsanleitung

Texas Instruments

Texas Instruments TAS6424E-Q1 Bedienungsanleitung

Texas Instruments

Texas Instruments INA231EVM Bedienungsanleitung

Texas Instruments

Texas Instruments bq27421 EVM Bedienungsanleitung

Texas Instruments

Texas Instruments ADS9224REVM-PDK Bedienungsanleitung

Texas Instruments

Texas Instruments eInfochips TMDXEVM6657L Produkthandbuch

Texas Instruments

Texas Instruments Stellaris LM4F120 LaunchPad Bedienungsanleitung

Texas Instruments

Texas Instruments DAC124S085EVM Bedienungsanleitung

Texas Instruments

Texas Instruments PCM1802EVM Bedienungsanleitung

Texas Instruments

Texas Instruments INA4290 Bedienungsanleitung

Texas Instruments

Texas Instruments TPS61090EVM-029 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Gigabyte

Gigabyte GA-9IVDT Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung