Texecom premier 60ixd Bedienungsanleitung
INSTALLATION MANUAL
60 Zone iD Expansion Module
INS261-8
INS261-8 2/21
Content
1.1 Introduction 4 .........................................................................................................................
1.2 PCB Layout 6 ..........................................................................................................................
1.3 Installation 8 ...........................................................................................................................
1.4 iD Connections 9 ....................................................................................................................
1.5 Commissioning and Testing 14 ...............................................................................................
1.6 Specifications 20 ....................................................................................................................
1.7 Standards 20 ..........................................................................................................................
INS261-8 3/21
INS261-8 4/21
1.1 Introduction
The Premier Elite 60IXD expander module provides up to 60 zones of expansion
using iD biscuits. The module has two loops each supporting up to 30 iD biscuits.
The 60IXD module can be installed in one of two modes:
Local Mode
The local mode allows the 60IXD to be connected to the expansion port on the
Premier Elite 24/48/88/168/640 control panels. This mode provides the following
facilities:
Two loops each supporting up to 30 iD biscuits
Fused 12V output for powering detectors
Advanced diagnostics using the system remote keypad
Biscuits can be mapped to any zone in the system
N The 60IXD expander module is only supported on Premier Elite 88/168
control panels from version 5.0 onwards Premier Elite 24 from Version 10.0
onwards and Premier Elite 48 from version 2.0 onwards. The Premier Elite 48 can
only support a maximum of 48 zones/biscuits. The Premier Elite 24 can only
support 24 biscuits
Network Mode
The network mode allows the Premier 60IXD to be connected to the network
terminals of any Premier control panel. This mode provides the following facilities:
Two loops each supporting up to 30 iD biscuits
Module reports as either 4 or 8 zone expanders (8XP)
Fused 12V output for powering detectors
Local diagnostics using an engineer’s keypad
Biscuits are mapped to a fixed expansion zone
N Although the 60IXD expander module can support 60 zones of
expansion, you can only utilise the expandable zones available on the control
panel, e.g., If the Premier Elite control panel only supports two zone expanders,
you can only use a maximum of 16 iD biscuits (2 x 8).
INS261-8 5/21
‘iD’ and ‘iD PLUS’ is a registered trademark of Novar ED&S.
INS261-8 6/21
1.2 PCB Layout
1 Harness connection to control panel (Local Mode)
2 Engineer’s keypad connector for local diagnostics
3 Receive data LED for Network connections
4 Network terminals for connection to a Premier control panel (Network Mode)
5 Auxiliary 12V (fused by F1) power for powering detectors
6 iD biscuit Loop 1 and 2
7 Short circuit indicator LEDs for iD loops 1 and 2
INS261-8 7/21
8 Local Mode communication indicator LED
9 Tamper switch connector
) Address selector (Network Mode)
+ Heartbeat/Power indicator LED
" Auxiliary 12V fuse (electronic) and fault indicator LED
INS261-8 8/21
1.3 Installation
Before connecting the 60IXD expander module, isolate ALL power from the control
panel (AC mains and battery), do not continue if there is still power present on the
control panel.
Local Mode
THIS MODE MUST NOT BE USED ON PREMIER ELITE V2.09 OR LATER.
NETWORK MODE MUST BE USED TO ENSURE CORRECT OPERATION.
1. Fix the expander module as close as possible to the control panel.
2. Route the harness lead from the control panel into the expander module.
3. Plug one end of the connection harness onto JP2 of the expander module and
the other end onto the expansion port (JP7) of the control panel.
4. Connect the iD devices to the expander module, see "iD Connections".
5. Reapply power to the control panel and program the necessary options on the
panel, see "Commissioning and Testing".
Note: On Premier Elite V2.09 and later Network mode should always be used.
Network Mode
1. Fix the module in the required location.
2. Connect the network connections of the module to the network connections of
the control panel.
3. Set the address switch to the require position (see table below)
4. Connect the iD devices to the expander module, see "iD Connections".
5. Reapply power to the control panel and program the necessary options on the
panel, see "Commissioning and Testing".
INS261-8 9/21
1.4 iD Connections
Each iD biscuit is connected across a two-wire detector loop. Apart from observing
the correct polarity, any wiring configuration can be used, as shown in the diagram
below:
INS261-8 10/21
* See next Note.
Cabling Considerations
The iD loop can be wired using standard 4-core alarm cable; however it is highly
recommended that screened cable is used to improve RF/false alarm immunity.
The use of 4-core cable allows 2 cores to be used for the iD biscuit and 2 cores for
supplying 12V power for PIR's etc.
The maximum cable run depends on the type of biscuits that are connected to the
module:
Andere Handbücher für premier 60ixd
1
Inhaltsverzeichnis
Andere Texecom Steuereinheit Handbücher
Texecom
Texecom Premier Elite Bedienungsanleitung
Texecom
Texecom Speech Module Bedienungsanleitung
Texecom
Texecom GSM MODULE Bedienungsanleitung
Texecom
Texecom INS656-3 Bedienungsanleitung
Texecom
Texecom Premier Elite iProx Bedienungsanleitung
Texecom
Texecom Premier Elite Com GSM Bedienungsanleitung
Texecom
Texecom CEJ0000 Bedienungsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
