Texecom Premier Elite 32XP-W Bedienungsanleitung

Installation Manual

Premier 32XP-W

INS467

Premier 32XP-W Installation Manual

1. Contents

1.Contents .......................................................................................................2

2.Premier 32XP-W ...........................................................................................4

3.System Design Considerations..................................................................5

Learning Devices.............................................................................................5

Placing Devices...............................................................................................5

4.System Overview......................................................................................... 6

Mounting the Expander.................................................................................... 8

Wiring ................................................................................................................ 8

Selecting an Address....................................................................................... 9

5.Programming..............................................................................................10

Premier 48/88 & 168 V8.15 Firmware & later................................................ 10

Option Switch Settings..................................................................................10

Configuring Radio devices............................................................................10

Deleting Devices............................................................................................11

Premier 24 V7.00-V8.23, 48/88/168 V7.00 – V8.14, 640 V7.00-V8.15........... 12

Option Switch Settings..................................................................................12

Expander Settings.........................................................................................12

Premier SmartKey™ Status LED Indications..............................................12

Deleting Devices............................................................................................13

Premier 412/816 V11.10 & Later, Premier 832 V4.10 & Later...................... 14

Option Switch Settings..................................................................................14

Expander Settings.........................................................................................14

Removing Detectors......................................................................................15

Learning Premier SmartKey™ ......................................................................15

Removing Premier SmartKey™....................................................................17

Premier 412/816 V10.5 – V11.07 & Premier 832 V3.50.-.V4.07.................... 17

Option Switch Settings..................................................................................17

Expander Settings.........................................................................................17

Premier SmartKey™ Status LED Indications..............................................18

Removing Detectors......................................................................................19

Learning Premier SmartKey™ ......................................................................19

Removing Premier SmartKey™....................................................................21

Learning Devices directly to the32XP-W ...................................................... 22

Using the Engineers Keypad......................................................................... 23

Device list ......................................................................................................23

Update Devices.............................................................................................27

Walktest Mode...............................................................................................28

System Status ...............................................................................................29

Device Status Indications..............................................................................30

Premier 32XP-W Installation Manual

6.Modes of Operation ...................................................................................31

Commission Mode..........................................................................................31

Expander....................................................................................................... 31

Device Commission Mode ........................................................................... 31

Device Specific Functions..............................................................................31

Prestige XT-W & Prestige QD-W ................................................................... 31

ImpaqPlus-W................................................................................................. 31

Impaq Contact-W .......................................................................................... 32

Walktest Mode ................................................................................................32

Control Panel................................................................................................ 32

Expander....................................................................................................... 32

Engineers Keypad........................................................................................ 32

RICOCHET™ Monitor.................................................................................. 32

7.System Attributes ......................................................................................33

Polling..............................................................................................................33

System Devices...............................................................................................33

Auto Mode..................................................................................................... 33

Always Awake............................................................................................... 33

Premier SmartKey™ ........................................................................................33

LED Indications............................................................................................. 33

PA Activation................................................................................................. 34

Enable/Disable Alarm Status LED’s............................................................. 34

Auxiliary Functions........................................................................................ 34

Instant Disarm............................................................................................... 35

Alarm Status LED’s....................................................................................... 35

Arm Fail Indication........................................................................................ 35

Battery Considerations...................................................................................36

Premier SmartKey™...................................................................................... 36

Low Battery Warning .................................................................................... 36

Battery Maintenance..................................................................................... 36

8.Specifications.............................................................................................37

Electrical..........................................................................................................37

Standards........................................................................................................38

Warranty ..........................................................................................................38

Notes................................................................................................................39

Premier 32XP-W Installation Manual

2. Premier 32XP-W

Texecom has developed a new method of wireless security signalling based on the concept of

mesh networking. Mesh-networking is the process whereby every single wireless device is

capable of receiving and retransmitting any signal from any other wireless device on the network.

The size, scalability and range of the entire system are extended as wireless signalling is no longer

limited by point-to point communications. The range of a RICOCHET™ enabled wireless system is

greater than previous systems, with multiple devices capable of relaying messages to and from

even the most remote locations in a building. Each RICOCHET™ enabled device provides

signalling routes to and from Premier control panels. If the wireless communication between

devices weakens, the RICOCHET™ network ‘self-heals’ and automatically re-routes

communications via alternate RICOCHET™ enabled devices. The reliability of the wireless system

increases as more RICOCHET™ devices are installed. SignalSecurity™ further enhances network

reliability with each device already aware of the number of communication paths available to it.

The PREMIER 32XP-W expander can be used on any premier control panel; however certain

features and functions are dependent on the version of panel firmware as detailed in the table

below. To determine the firmware version of your control panel press 4 on the keypad.

Firmware versions prior to those listed are NOT compatible.

Control Panel Premier 32XP-W Legacy RICOCHET™

Premier 412 1 V10.5 – V11.07 V11.10

Premier 816 1 V10.5 – V11.07 V11.10

Premier 816E 0 Not supported

Premier 832 1 V3.5 – V4.07 V4.10

Premier 24 1 V7.00 – V8.23 Not Released

Premier 48 1 V7.00 – V8.13 V8.15

Premier 88 1 V7.00– V8.13 V8.15

Premier 168 1 V7.00 – V8.13 V8.15

Premier 640 1 V7.00 – V8.15 Not Released

Premier 32XP-W Installation Manual

3. System Design Considerations

To ensure correct setup and operation of the Wireless Network it is important that the following

procedures are used when learning and placing devices.

Learning Devices

All devices should be learnt before they are placed in their final location. The expander should be

in commission mode, please see page 31.This will ensure that they are registered on the receiver

or control panel, and that Mesh Networks and routing are established correctly. Please refer to the

relevant section in this document to Learn Devices to the system.

Devices should be at least 30cm’s away from the receiver when being learned.

Placing Devices

Once all of the devices have been learnt, they will need placing in their desired location, this

should be done by installing devices closest to the expander first and then working outwards so

that the last devices installed are those furthest away from the expander.

Make sure to install devices with the expander in Commission mode. See page 31.

Devices also have a commission mode which will indicate a secure and valid path of

communication to the receiver. See page 31.

You should wait at least 15 minutes after installing the last device to make sure routing has

been correctly established between all system devices.

For maximum reliability and system integrity avoid long and thin set-ups.

Devices are capable of hopping through up to two other devices, or a maximum of three

hops.

Premier 32XP-W Installation Manual

4. System Overview

12V TR0V

1 2 3 4 5 6 7 8

243 1

243

2 4

8910

12341234

1: Engineers Keypad Connection

An engineer’s keypad (Premier LCD keypad and interface lead) can be temporarily plugged onto

this connector to allow system programming and testing. (Functions dependent on Panel firmware

version) Set the keypad address switches to all on.

2: Network Connection

The + and – terminals provide power whilst the T and R terminals are transmit and receive data.

Premier 32XP-W Installation Manual

3: For Future Use

4: Comm. Port Connection

Serial communications port for connecting the 32XP-W to a PC via PC Com for use with

RICOCHET™ Monitor Software.

5: Lid Tamper

When open puts the system into commission mode and digitally attenuates the receiver signal by

6Db.

6: Programming LED’s

Allows programming of devices directly to the receiver, in conjunction with the learn switch.

7: Antenna

RF Antenna.

8: Network LED's

Green LED = Data received by the expander from the panel Red LED = Data transmitted by the

expander to the panel. (The flash rate depends on the mode and RF activity)

9: Heartbeat LED

Flashes steadily to indicate that the receiver is functioning correctly. If the light is ON or OFF all the

time, then there could be a hardware problem.

10: Learn Switch

To be used with programming LED’s to learn devices directly to the receiver.

11: Options Switch

Use to select the receiver functionality depending on panel firmware.

Switch 1 ON =firmware dependant, please see the relevant programming section.

Switch 2 ON = Legacy Mode

OFF = RICOCHET™

Switch 3 Not Used

Switch 4 Walk test

12: Address Switch

Used to assign the address of the receiver on the premier network

13: RF LED

Flashes when transmitting or receiving RF data

14: Tamper Disable

Disables the lid and rear tamper

15: Engineer’s Keypad LED's

Red LED flashes constantly, the flash rate increases when data is being transmitted.

Premier 32XP-W Installation Manual

Mounting the Expander

Remove each screw cap by inserting a flat bladed screwdriver into the slot and turning anti-

clockwise, excessive force is NOT required. Remove both of the cover screws and put them in a safe

place along with the screw caps. Gently pull the cover away from the base applying slight pressure

to the sides at the top of the expander if required. The front cover should now be off.

Mount the expander using at least two appropriate countersunk screws (no larger than No. 8). A

keyhole slot has been provided to assist mounting and aid levelling.

If required a screw should be placed into the knockout on the rear of the expander to enable the

rear/wall tamper.

12V T R0V

1 2 3 4 5 6 7 8

12341234

Wiring

It is strongly recommended that the system is completely powered down (mains and battery) before

wiring the expander. Connect the expander to the control panel using 4-core cable as follows:

Expander Control Panel Description

+ + +12V Supply

- - 0V Supply

T T Transmit Data

R R Receive Data

Premier 32XP-W Installation Manual

The networks are made up of four terminals incorporating power and data. To ensure correct

operation, all four terminals on the device must be connected to the corresponding terminals on the

control panel or previous device.

Expanders can be connected using 4-core cable. However, it is recommended that 6 or 8-core cable

is used as the spare cores can be used to ‘Double Up’ on the power connections if needed.

Standard 7/0.2 alarm cable can be used for most installations. However, under certain

conditions it may be necessary to use screened cable.

Selecting an Address

Each expander must be assigned a different address using the DIL switches located on the PCB.

The table below shows the expander addressing:

Address DIL 1 DIL 2 DIL 3 DIL 4

1 On or Off Off Off Off 2 431

2 Off On Off Off 2 431

3 Off Off On Off 2 431

4 Off Off Off On 2 431

5 On Off Off On

6 Off On Off On 2 431

7 Off Off On On

1 2 3 4

8 On Off On On

2 431

Never set two expanders on the same network to the same address. Expanders are factory set

to address 1.On legacy panels the expander will occupy 1 x Expander slot on the control

panel, as well as the Network Receiver slot.

Premier 32XP-W Installation Manual

5. Programming

It is highly recommended that you upgrade the Panel Firmware to the latest version to ensure full

compatibility; however the system is backwards compatible as detailed in the table on page 4

Premier 48/88 & 168 V8.15 Firmware & later

Option Switch Settings

For this version of firmware all option switches should be OFF.

Configuring Radio devices

Up to 32 wireless devices of any combination can be learnt on to the system. The number of

Premier SmartKey™ is limited to the maximum number of users (i.e. 24 0n the Premier 48).

Wireless devices can then be mapped on to the system along with conventional detectors.

The top line on the display shows the serial number of the device and also the status i.e. Active,

Tamper etc.

The bottom line of the display shows the signal strength and also which zone/user the device is

mapped to.

Signal strength should be greater than 30.

Signal strength is only displayed when in commission mode. When not in commission mode

the keypad will display 255.

The signal range is between 0 and 99

In the case of devices that are hopping the display on the panel keypad shows the average of

the hopped signal strengths.

Follow the instructions on the next page to learn devices to the system, once complete follow the

instructions in the relevant control panel manual to programme zone type, attributes and user

permissions. Place devices in their final location ONLY after they have been learned to the system.

Andere Handbücher für Premier Elite 32XP-W

Inhaltsverzeichnis

Andere Texecom Extender Handbücher

Texecom

Texecom Premier Elite 32XP-W Bedienungsanleitung

Texecom

Texecom premier 60ixd Bedienungsanleitung

Texecom

Texecom Premier OP16 Bedienungsanleitung

Texecom

Texecom W/32XP-W Bedienungsanleitung

Texecom

Texecom Premier Elite 8XP Bedienungsanleitung

Texecom

Texecom Premier8XP Bedienungsanleitung

Texecom

Texecom Premier 8X Bedienungsanleitung

Beliebte Extender Handbücher anderer Marken

SY HDBT-60T Bedienungsanleitung

Appsys ProAudio

Appsys ProAudio ADX-16 Bedienungsanleitung

Atlona

Atlona RS232 Bedienungsanleitung

IDK

IDK OPF-TH1000-A Bedienungsanleitung

Enable-IT

Enable-IT 824WP Bedienungsanleitung

Worx

Worx Landroid RadioLink WA0864 Technisches Datenblatt

TP-Link

TP-Link TL-WA730RE Bedienungsanleitung

Camplex

Camplex CMX-HDMI-SFPL Bedienungsanleitung

SC&T

SC&T HE03-4K Bedienungsanleitung

Marmitek

Marmitek MegaView70 Bedienungsanleitung

Samsung

Samsung SCS-26UC4 Bedienungsanleitung

Foxun

Foxun SX-GES24 Bedienungsanleitung

MuxLab

MuxLab 500771 Bedienungsanleitung

foxunhd

foxunhd SX-AEX01 Bedienungsanleitung

TERK Technologies

TERK Technologies LFIRX2 Bedienungsanleitung

Devolo

Devolo Audio Extender Handbuch

Edimax

Edimax EW-7438RPn V2 Bedienungsanleitung

Shinybow USA

Shinybow USA SB-6335T5 Bedienungsanleitung