Texi XYZ 2518 Bedienungsanleitung

TEXI XYZ 2518

MANUAL

CATALOGUE 
Machine Introduction...............................................................................................................3
1 Power and cable requirements...................................................................................3
2 Introduction...................................................................................................................4
Accessories Installation.......................................................................................................5
1 380V...................................................................................................................................5
2 220V...................................................................................................................................7
Installation of CUT Software & IP Settings.................................................................10 
1 Introduction.................................................................................................................10 
2 Installation.................................................................................................................10 
3 IP Settings...................................................................................................................11 
Settings of the Cut Software.............................................................................................12 
Operation of the Cut Software...........................................................................................13 
1 Import Processing File.............................................................................................13 
2 Export the Processing File.....................................................................................15 
3 SP number.......................................................................................................................16 
4 Optimize the Processing Graph...............................................................................18 
5 Send Graph to the Machine.......................................................................................19 
6 Please refer to Operation Examples for other main functions ...................19 
Control Panel...........................................................................................................................19 
1 Screen saver interface.............................................................................................19 
2 Work Page.......................................................................................................................19 
3 Adjust Page...................................................................................................................22 
4 Speed Page.....................................................................................................................24 
5 Config Page...................................................................................................................27 
6 Test Page.......................................................................................................................29 
Tools Installation and Knife Depth Setting.................................................................31 
1 Oscillating Knife Cutting Tool（SP4，cut,Head1）.........................................32 

7.2 Pneumatic Oscillating Cutting Tool（SP4, cut,Head1）.................................36

7.3 Driven rotary tool（SP4, cut，Head1）...............................................................36

7.4 Universal Cutting Tool(Drag Knife)(SP4, cut，Head1；SP2, Tcut,Head2) .37

7.5 Kiss Cutting Tool (SP4,cut,Head1；SP2,Tcut,Head2) .......................................38

7.6 Creasing Wheel Tool（SP2,Tcut,Head2）...............................................................39

7.8 V-cut Tool.....................................................................................................................40

7.9Punching Tool（SP2）...................................................................................................44

7.7 Milling Tool（SP6）...................................................................................................46

8.Test Angle and Test Offset.................................................................................................47

8.1 Test Angle.....................................................................................................................48

8.2 Test Offset...................................................................................................................49

9.Maintenance...............................................................................................................................50

1.Machine Introduction

1.1 Power and cable requirements

In view of the power of the vacuum pump is different, electric power

at 220V or 380V can be used according to the actual situation. The

total power of the machine is at least 14KW, so the cable cross section

requires at least 8mm².

Items

Peak power

Machine

3KW

Vacuum Pump

11KW

Air Compressor

1.2KW

1.2 Introduction

(1)The left one is the 380V model machine and its accessories.

(2)The right one is the 220V model machine and its accessories.

Number

Item

①

Distribution Box

②

Returning-air Box

③

Air Compressor

④

Vacuum pump

⑤

Control Box

（Note：

1.When 380V voltage is used for power supply, only three live wires

need to be used, and there is no need to use the null wire.

2.For models without transformer, it is necessary to provide 220V power

supply system for equipment other than vacuum pump.

3.No returning-air box for the machine which has no auto-feeding system.

4.There is no air compressor for the machine without using it.

5.Some models have no distribution box, only a certain number of AC

contactors are attached.）

2.Accessories Installation

2.1 380V

(1)Distribution Box

①.Input

A.Connect the U-shaped terminals of the Signal&Protection cable to the

A1&A2 of the AC contactor.

B.Connect the three live wires of the 380V three-phase electricity to

the 1/L1，3/L2，5/L3 of the AC contactor separately.(Note:If the fan

reverses, the position of two live wires can be changed arbitrarily)

C.Connect the 220V Power Cable to the 220V power supply socket.

②.Output

A.Connect the aviation plug of the Signal&Protection cable to the “Air

Pump”port on the machine.

B.Connect the green cable which has the white wire connectors to the

protector wires on the vacuum pump，as shown in the red frame below:

C.Connect one end of the Power Cable for the Vacuum Pump to the 2/T1，

4/T2,6/T3 of the AC contactor and connect another end to the vacuum

pump, as show in the red frames below:

D.Connect the aviation plug of the 220V Power Cable to the machine or

the control box.(Note:Subject to the actual model.)

(2)Vacuum Pump of the Digital Knife Cutting Machine with Flat Table

(3)Vacuum Pump and Returning-air Box of the Auto-feeding Digital Knife

Cutting Machine.(Note:There is no returning-air box for the non auto-

feeding model machine.)

①Connect No.1 to the air pipe which comes out of the machine.

②Connect No.2(The signal cable of the returning-air box) to the

“Returning Air Box”port on the machine.

③Connect No.3 to the No.6(The inlet of the vacuum pump) by the air

pipe.

④Connect No.4(Solenoid valve) to the oil water separator(Pneumatic

valve) on the machine by the air tube.

⑤Connect No.5 to the No.7(The outlet of the vacuum pump) by the air

pipe.

⑥No.8 is the Hush pipe, No.9 is the pressure relief valve, it must

be installed onto the reducer which is connected to the inlet of the

vacuum pump. No.10 is the mini distribution box.

After connection finished，as shown below：

2.2 220V

(Note:Take the auto-feeding machine as an example)

(1)Distribution Box

①Input

A.Connect the U-shaped terminals of the Signal&Protection cable to the

A1&A2 of the No.1 AC contactor.

B.Connect the 220V power supply cables to the 2/T1 and 6/T3 of the

No.1 and No.2 AC contactors separately(Note:No.5 and No.6 are connected

to the 220V cables.You need to prepare 220V power supply cables by

yourself)

C.Connect the 220V Power Cable to the 220V power supply socket

(Note:The 220V power supply cables which are connected to the

distribution box must can bear at least 10KW power, the 220V Power

Cable which is sent with the machine is only supply the electricity to

the machine and control box, and the power of the machine is about

2500W)

②Output

A.Connect the aviation plug of the Signal Cable to the “Air Pump”

port on the machine.

B.Connect the two groups of Vacuum Pump Power Cables to 1/L1 and

5/L3(Note:No.3 and No.4 of the AC contactors are connected to the

vacuum pumps) of No.1 and No.2 AC contactors separately, and connect

the other end of each vacuum pump power cable to No.2 and No.3 feet or

No.1 and No.3 feet of each vacuum pump separately,as shown below:

(2)Vacuum Pump and Returning-air Box of the Auto-feeding Digital

Knife Cutting Machine.(Note:There is no returning-air box and Part B

for the non auto-feeding model machine.)

(Note:Part A is connected to the inlet of the vacuum pump and Part B

is connected to the outlet of the vacuum pump)

①Connect No.1 to the air pipe which comes out of the machine.

②Connect No.2(The signal cable of the returning-air box) to the

“Returning Air Box”port on the machine.

③Connect No.3 to the No.6 by air pipe, and connect the No.7,No.8,No.9

and No.10 of the Part A to the inlet of every vacuum pump.

④Connect No.4(Solenoid valve) to the oil water separator(Pneumatic

valve) on the machine by the air tube.

⑤Connect No.5 to the No.11 by air pipe, and connect the No.12,No.13

and No.14 of the Part B to the outlet of every vacuum pump.

⑥The No.16 is the pressure relief valve，the arrow on the pressure

relief must face the Part A, and it to the Part A by the tape firmly.

2.3 Air Compressor

（Note:1.Air compressor with power over 7.5kW is required for the

Pneumatic oscillating Knife Tool and you need to prepare it by yourself.

2.There is no air compressor for the machine without using it.）

（Note:It is recommended to discharge water once every one to seven

days）

3.Installation of CUT Software & IP Settings

3.1 Introduction

Cut is a cutting service software for editing and cutting tasks. It

can be well matched with mainstream graphic design software. The

software can be used for drawing simple graphs. You can also use CAD,

CorelDraw,AI and other graphic design software. Then send graph to the

machine for cutting via Cut.

3.2 Installation

Inhaltsverzeichnis

Andere Texi Cutter Handbücher

Texi

Texi Zorro 110 Free Bedienungsanleitung

Beliebte Cutter Handbücher anderer Marken

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Bedienungsanleitung

Makita

Makita 4112HS Bedienungsanleitung

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Bedienungsanleitung

Hitachi

Hitachi CM 4SB2 Fehlerbehebungshandbuch

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Bedienungsanleitung

GCC Technologies

GCC Technologies AFJ-24S Bedienungsanleitung

DeWalt

DeWalt XR LI-ION DCS350N Bedienungsanleitung

Baudat

Baudat ES1 Bedienungsanleitung

Mafell

Mafell ZAF 200 Leitfaden

Makita

Makita 4100NH Bedienungsanleitung

Formax

Formax FD 574 Bedienungsanleitung

EINHELL

EINHELL TE-MA 1500 Bedienungsanleitung

Husqvarna

Husqvarna Cut-n-Break K 760 Bedienungsanleitung

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Bedienungsanleitung

TRI tool

TRI tool 301A Bedienungsanleitung

Roller

Roller King 1 1/4 Bedienungsanleitung

RODCRAFT

RODCRAFT RC7170 Bedienungsanleitung