Texi Smart S+B Bedienungsanleitung

Texi Smart S+B

Instruction manual

TEXI SMART S+B 2

SAFETY RULES

• Before operating the machine read the instruction manual carefully. It contains important advices for safe

and efficient use and maintenance of the machine.

• Please keep the manual, warranty card, proof of purchase and, where possible, the original packaging. If

you want to pass the machine to another person - give it together with instruction manual and warranty card.

• After unpacking, make sure that the machine is not damaged. In case of doubt, contact an authorized

service.

• Do not leave plastic bags, pieces of foam, staples, etc., remaining after unpacking the machine within the

reach of children or persons with reduced psychophysical efficiency.

WARNING! Do not allow children to play with foil. Danger of suffocation!

• Safe use of this machine will only be possible when it is properly connected to a grounded electrical

system. Supplier / Distributor shall not be liable for any damages arising from connecting to the installation,

which fails to meet safety requirements.

• Before connecting the machine make sure that the voltage on the rating plate complies with the mains

voltage. In case of doubt, contact a qualified electrician.

• It is not recommended to use adapters, splitters and extension cords. If necessary, use only certified,

accessories, corresponding to current safety standards, making sure they are appropriate for your electrical

system and comply with the technical parameters of the machine.

• Connecting the machine in a manner inconsistent with the instructions threatens your safety and may

cause voiding the warranty.

• Remember:

- Do not use the machine for purposes other than those described in this manual,

- Do not use the machine barefoot or with wet hands or feet,

- Do not use the machine outside,

- Do not expose the machine to weathering (sun, rain, wind, ...),

- Do not allow children or persons with reduced psychophysical efficiency to use the machine,

- Never pull the power cord or the machine to disconnect it from the electric network,

- Do not leave the machine connected to the mains, without supervision,

- Never immerse the machine in water or other liquids.

• User cannot exchange electric cable on his own. Contact an authorized service or qualified personnel, if the

exchange is necessary.

• Turn off and unplug the machine if it breaks down or works incorrectly. Contact an authorized service for

repair with use of original spare parts. Do not attempt repairs yourself.

• To prevent the continued use of the machine after its worn, unplug it from the mains and cut the electric

cord. Follow local rules for disposal of waste.

• Seller / Distributor shall not be liable for any damage caused to persons, animals or things by improper

connection or resulting from misuse, improper or excessive use.

• This machine is not a toy!

TEXI SMART S+B 3

GENERAL INFORMATION

Texi Smart S+B is a suction and blowing ironing table with steam station and iron.

1. SPECIFICATIONS:

MODEL:

Texi Smart S+B

POWER SUPPLY:

220-240 V–50-60 Hz

TOTAL INSTALLED POWER:

2388 W

POWER OF IRON:

800 W

BOARD POWER:

200 W

VACUUM/BLOWING POWER:

40 W

BOILER POWER:

1300 W

PUMP POWER:

48 W

BOILER CAPACITY:

1.9 L.

NET BOILER CAPACITY:

0.95 L.

WATER TANK CAPACITY:

1.1 L.

IRONING ENDURANCE:

CONTINUOUS

OPERATING STEAM PRESSURE:

2.8 BAR

WEIGHT:

26 kg.

OVERALL DIMENSIONS (OPEN):

136x44x105 h. cm

OVERALL DIMENSIONS (CLOSED):

136x44x24 h. cm

MADE IN ITALY

LEGEND

COVER

IRONING ARM

CABLE SUPPORT SPRING

IRON CABLE SUPPORT

IRON

IRON HOLDER

SLEEVE ARM FIXING KNOB

POWER SUPPLY CABLE

IRON REST

WATER DISCHARGE SCREW

PLUG. WARNING: HOT WATER

WHEELS

ELECTRIC + STEAM PLUG

WITH SECURITY BLOCK-CAP

TEXI SMART S+B 4

2. IMPORTANT

Before installing Texi Smart S+B, it is necessary to set up the following:

1. Protected electrical outlet suitable to its power (itisrecommendedtouseanearthprotectorthermo-

magnetic switch 16 A and Id 30mA).

2. Flat,evensurfaceontowhichthemachinewillbeplaced.

3. OPENINGTHEPACKAGE

1. Open the box containing the Texi Smart S+B, take out the instruction manual and read it very

carefully.

2. Remove Texi Smart S+B from the box and insert the cable support deep into the special hole

(fig.1).

3. Fix the cable support spring to the cable support, avoiding twining.

4. Put the iron on the iron rest. (fig. 1).

4. CONNECTING AND STARTING

FUNCTIONS OF KEYS

Main ON/OFF key

Boiler ON/OFF key

Iron ON/OFF key

ON/OFF

Vacuum / blowing motor ON/OFF key

Manual / automatic mode switch

Note: in manual mode the vacuum/blowing motor works continuously, in automatic mode the

vacuum/blowing motor works upon pressing the micro-switch of the iron.

Key to change the motor function from vacuum to blowing and

vice-versa.

TEXI SMART S+B 5

ON/OFF

To access the internal menu press both keys together.

With Texi Smart S+B switched off and disconnected plug:

1. Vertically hold the ironing board, being sure that the boiler is towards the floor;

2. Pull the board legs until the desired height has been reached (fig. 2);

3. Install the electric + steam plug in the socket placed on a side of the steam generator

(Fig. 1.12). Block it with the security cap of the outlet.

4. Take off the water plug of the Texi Smart S+B (fig. 3), and fill the water tank (roughly 1 liter).

Once this has been done, replace the water plug.

5. Insert the plug (Fig. 1.8) into a 230V 16 A socket and turn on the machine by pressing the green

key;

6. Select the desired function (iron, boiler, working mode, etc.).

WARNING: the electronic board automatically performs a check of

the software installed.

If an error or fault is found, the “safety” device blocks the electronic

board and does not allow normal functioning. “SOFTWARE

ERROR”will be displayed. Contact the Authorized Service Centre

to update the software.

WATER FILLING

Fig. 3

5. MEANING OF ICONS

INTERMITTENT LIGHT: indicates that the boiler is on and water is being heated to

obtain steam

FIXED LIGHT: indicates that the boiler is on and its pressure is optimum Texi Smart

S+B is ready for ironing

Indicates that the iron is functioning

INTERMITTENT LIGHT + SOUND ALARM: indicates that water is missing inside

the water tank.

FIXED LIGHT: indicates that the pump is pumping water into the boiler.

Indicates –when the light is on, the vacuum / blowing motor is on.

Light is off –motor does not work.

Fig. 2

TEXI SMART S+B 6

When the light is on, the machine works in manual mode (the vacuum / blowing

motor works continuously). When the light is off –the machine works in automatic

mode (the vacuum / blowing motor works upon pressing the micro-switch of the

iron).

Indicates a malfunction which requires technical assistance or that the maximum

number of hours set for the cover changing has been exceeded.

NOTE:

During ironing the icon will start flashing. This is normal and indicates that the heater is working,

restoring the optimum pressure inside the boiler.

If the icon turns on every now and then, this indicates that the Texi Smart S+B is pumping

water into the boiler. It is therefore important to always fill the water tank (fig. 3).

It is possible to change the motor function (vacuum or blowing) and the functioning (continuous or

with iron micro-switch) anytime by using the keys indicated in “FUNCTIONS OF KEYS”.

6. MENU

To access the MENU, press both keys for a few seconds as shown on the left. To

exit the MENU, press ESC or wait for 5 seconds. To scroll up or down use the

arrows.

AVAILABLE SETTINGS:

HOURS OF

WORK

TOTAL HOURS:

Cannot be zeroed

To exit

or wait for 5

seconds

ON/OFF

PARTIAL HOURS:

Zeroing of hours

Press for 6 sec.

TOTAL HOURS: computation of the total hours the machine has worked for. This data cannot be

zeroed.

PARTIAL HOURS: computation of the hours the machine has worked since last zeroing. This data

can be zeroed (see table). To zero the data, follow instructions as per below table.

ON/OFF

TEXI SMART S+B 7

RESET OF WARNINGS is necessary in order to delete the warnings from the display once the cover

has been changed.

Example: WARNING: CHANGE COVER is displayed.

1. Access the MENU

2. find RESET WARNINGS, press OK and find CHANGE COVER

3. press RESET until you hear an acoustic signal

4. ESC to exit the SET menu.

KEY TONE

KEY TONE ON

To confirm

To exit

or wait for 5

seconds

ON/OFF

KEY TONE OFF

KEY TONE is used to activate or deactivate the acoustic signal when keys are pressed.

If you wish the acoustic signal to be deactivated, press KEY TONE OFF.

MAINTENANCE

Password needed. Service Centre authorized access only

MANUFACTURER

Password needed. Manufacturer authorized access only

WARNING: AFTER 10 ATTEMPTS TO ACCESS THE “MAINTENANCE” OR

“MANUFACTURER” MENU WITHOUT TYPING IN THE PASSWORD, AND/OR EVERY TIME

THE WRONG PASSWORD IS TYPED, THE MENU WILL BE BLOCKED. “PASSWORD

BLOCKED” will be displayed. To unblock the menu, contact the Authorized Service Centre or the

manufacturer.

LANGUAGE

ITALIAN

To confirm language

To exit

or wait for 5

seconds

ENGLISH

GERMAN

FRENCH

POLISH

RESET OF

WARNINGS

CHANGE COVER

(the number of hours

elapsed since the last

change will be displayed)

To zero, press the key

until you hear an

acoustic signal

To exit press

or wait for 5

seconds

TEXI SMART S+B 8

ON/OFF

RUSSIAN

LANGUAGE allows to set operating language (see table). Languages may be different according to

the country of destination.

DELAY

0...12

seconds

To confirm

To exit

or wait for 5

seconds

ON/OFF

DELAY

OFF

ON/OFF

DELAY works only in the automatic mode. You can set the vacuum / blowing motor on delay (DELAY

ON)as well as off delay (DELAY OFF), in the range from 0 to 12 seconds. The settings are saved in

the memory. You can change the values according to your requirements.

The factory settings are: delay of the motor on –2 seconds, delay of the motor off –6 seconds.

7. WARNING LIGHT AND SOUND ALARM SIGNAL

The intermittent warning light , the sound alarm

signal with quick intermittency and the written warning

“WATER” are activated when there is no water inside the

water tank. Upon refilling the water tank the light and

sound alarm signal will switch off.

The fixed warning light together with , the

sound alarm signal with slow intermittency and the

written warning “WATER PUMPING” are activated: to

indicate a malfunction of Texi Smart S+B (the boiler is

without water and it is not possible to restore the correct

water level). In this case turn off the boiler and then turn it

on once again. If the warning light does not turn off - do

not insist, unplug the Texi Smart S+B from the mains and

contact authorized personnel.

WATER FILLING

Fig. 3

TEXI SMART S+B 9

8. PRINCIPLES OF SAFE AND EFFICIENT WORK

1. Use only normal tap water.

2. Never add additives to water.

3. Connect Texi Smart S+B to a suitable and protected socket.

4. Keep out of reach of children, both when it is on and off.

5. Do not iron garments directly on persons or things.

6. Never leave the iron on the board or on garments when it is on.

7. Never leave garments on the board when it is on, in order to avoid them from

getting spoilt or burnt.

8. ATTENTION: Texi Smart S+B may be switched on only when the ironing board

is open.

9. ATTENTION: put away Texi Smart S+B as shown (fig. 4). Never put it away

upside down (fig. 5).

9. WORKING WITH MANUAL AND AUTOMATIC MODE

1. When you choose the manual mode, the vacuum / blowing motor works continuously, unless it’s

switched off. To switch on or switch off the motor, use the key . To change the motor

function from vacuum to blowing or opposite use the key .

Note: While you first run your machine, the vacuum / blowing motor is off.

2. When you choose the automatic mode, the vacuum/blowing motor works upon pressing the

micro-switch of the iron. The way of working is showed on the below exemplary picture:

Example: The delay of the vacuum / blowing motor on, after pressing iron’s micro-switch, is set on 2

sec. The delay of the motor off, after releasing the iron’s micro-switch, is set on 6 sec.

Press the micro-switch of the iron and start ironing. After 2 seconds the vacuum / blowing motor will

start working. 6 seconds after releasing the micro-switch, the motor will stop working. By extended

time of the motor work, moisture is sucked out of the material and the effect of ironing is fixed.

Note: After pressing the micro-switch the steam will come out of the iron, after releasing –it will stop.

Fig. 4

Fig. 5

TEXI SMART S+B 10

10. IRONING

1. Seize the iron by the cork handle and press the micro-switch of the iron (fig. 7)

4-5 times sothat steam comes out. This is necessary in order to warm the hoses and avoid water

dripping from the iron.

2. Start ironing by pressing micro-switch of the iron (fig. 7), activating steaming. As a result, the

fibers of the ironed element are damped. Release the micro-switch to smoothen all creases. For

a good result, set the thermostat (fig. 6) on “cotton”.

3. For delicate, black or blue garments we suggest to use the anti-shine shoe.

4. During ironing, always put the iron on its rubber rest (fig. 1) and pay attention to the position of

the wires: if they twine or get in touch with the ironing board, they might cause short circuits.

5. For dry ironing it is possible to adjust the thermostat (fig. 6) on various positions according to the

type of fabric (check garment label). For steam ironing, set the thermostat on “cotton” or “flax”.

6. It is advisable to replace the padding (fig. 1) as soon as the vacuum of the ironing board is

unsatisfactory or when the padding presents some marks or rings of water.

11. REFILLING OF THE WATER TANK

It is possible to fill the water tank at any time, even when the boiler is functioning. Lift the water plug

and add water, paying attention not to spill it onto the machine (fig. 3). Water is required when the

intermittent warning “WATER” appears and the sound alarm signal switches on (chapter 7).

It is suggested to immediately add water once the sound alarm signal switches on. This avoids the

drop of pressure and therefore it is not necessary to wait for water heating.

12. REPLACEMENT OF COVER

After a certain number of hours the machine will signal that the board cover needs to be replaced.

This procedure must be carried out ONLY when the boiler and ironing board are cold and

disconnected from the mains.

Note: it is possible to wash the cover.

ATTENTION: It is necessary to reset the hour-counter (see chapter 6) every time the cover is

replaced. This will permit its correct functioning.

Note: The “CHANGE COVER” warning timing is based on an average use of the ironing board.

However, the wear and tear also depends on how ironing is done. It may therefore be necessary to

replace it even earlier, especially if vacuum/blowing performances have diminished.

Fig. 6

Fig. 7

ELECTRIC

CABLE

THERMOSTAT

MICROSWITCH

FOR IRON

STEAM HOSE

Inhaltsverzeichnis

Andere Texi Eisen Handbücher

Texi

Texi Hestia Bedienungsanleitung

Beliebte Eisen Handbücher anderer Marken

Clatronic

Clatronic DB 3703 Bedienungsanleitung

TEFAL

TEFAL FV4093Z0 Bedienungsanleitung

Gorenje

Gorenje SIH 2200 BS Bedienungsanleitung

Bosch

Bosch 2 Series Bedienungsanleitung

Riffel

Riffel Catena KB-819 Bedienungsanleitung

Maxwell

Maxwell MW-3010 Bedienungsanleitung

TREVIDEA

TREVIDEA Girmi ST60 Bedienungsanleitung

Primula

Primula Vapormat Bedienungsanleitung

Magio

Magio MG-541 Bedienungsanleitung

Bosch

Bosch Sensixx B22L Bedienungsanleitung

Philips

Philips GC651 Bedienungsanleitung

Vitek

Vitek VT-1247 VT Bedienungsanleitung

Cleanmaxx

Cleanmaxx 3397 Bedienungsanleitung

Philips

Philips GC800 Bedienungsanleitung

dyras

dyras ESI-2400AC Bedienungsanleitung

Philips

Philips PerfectCare PSG71 Series Bedienungsanleitung

GE 169061 Bedienungsanleitung

Gorenje

Gorenje SIH 2200 GC Bedienungsanleitung