Texmate CL-B101D40PS Bedienungsanleitung

CL-B101D40PS Manual (d0096) Page 1

CL-B101D40PS

Smart 101 segment, 4 digit LED Tricolor or Mono-color

digital bargraph controller with Programmable Scale

Factor input signal scaling and four fully programmable

set points in a switchboard style case for

monitoring, measurement, and control applications.

0.56” LEDs

•

External transmitters or signal conditioners can be eliminated by

direct connection of the sensor output to more than

40 Plug-in Input Signal Conditioners that include:

– AC/DC Current – Pressure – Resistance

– AC/DC Voltage – Process – Temperature

– Load Cell – Prototype – 4 to 20 mA

•

Optional isolated 16 bit analog output. User or factory scalable to 4

to 20 mA, 0 to 20 mA or 0 to 10 V across any desired digital span

from ± one count to the full scale range of – 1999 to 9999 (12000

counts).

•

A Programmable Tricolor (Red-Green-Orange) or mono color (red or

green), 101 segment high brightness bargraph.

•

Red 4-digit LED display with a range of -1999 to 9999

(12000 counts). Optional green digital display.

•

Front panel LED annunciators provide indication of setpoint status.

•

Two 9 Amp Form C, and two 4 Amp Form A or 4 x 4 Amp Form A

relays available

•

Auto-sensing AC/DC power supply. For voltages between

85-265 V AC / 95-300 V DC (PS1) or 18-48 V AC / 10-72 V DC

(PS2).

•

24 V DC excitation is available to power external 4/20mA

transmitters and 5 or 10 V DC excitation is available for

resistance bridge type sensors.

•

Provision to connect an external programming lockout switch.

•

Provision for external DIM switch to reduce the brightest

display setting by 50%.

•

Automatic intelligent averaging, smooths noisy signals while

providing a fast display response to real level changes.

General Features

Specifications

• Thebargraphcandisplay,full

scale, any desired portion of

the digital reading.

• Setpoint1hasdelay-on-make

and delay-on-break plus

a special “pump on pump

off” mode that creates a

Hysteresis Band between SP1

and SP2.

Software Features

•

Four programmable setpoints

with adjustable Hysteresis.

•

Bargraph center zero function.

• Relayactivationcanbeselect-

ed to occur above (hi) or below

(Lo) each setpoint.

• Digitaldisplayblanking.

• Decimalpointsetting.

• Four-levelbrightnesscontrol

LEOPARD

FAMILY

Input Specs:�� Depends on Input signal conditioner

A/D Converter:�� 14 bit single slope

Accuracy:�� ±(0�05% of reading + 2 counts)

Temp. Coeff�:�� 100 ppm/°C (Typical)

Warm up time:�� 2 minutes

Conversion Rate:�� 10 conversions per second (Typical)

Digital Display:��

4 digit 0.56" LED red (std), green (optn)

Range

–1999 to 9999 counts�

Bargraph Display:��

101 segment 235º circular red (standard),

Green (optional) or tricolor (optional) LED�

Polarity:�� Assumed positive� Displays – negative

Decimal Selection:�� Front panel button selectable, X•X•X•X•

Positive Overrange:�� Bargraph and top segments of digital display

flash�

Negative Overrange:�� First segment of bargraph and bottom seg-

ments of digital display flash�

Relay Output:�� Two 9 Amp Form C relays, two 4 Amp Form

A relays or

4 x 4 Amp Form A relays

Analog Output:�� Isolated 16 bit user scalable mA or V

OIC (mA out) ��

4-20 mA @ 0 to 500Ω max loop resistance

OIV (volts out) �� 0-10 V DC @ 500 Ω or higher resistance

Power Supply:�� AC/DC Auto sensing wide range supply

PS1 (std)��

85-265 VAC / 95-300 VDC, 50-400Hz 4.2W

PS2��

18-48 VAC / 10-72 VDC, 50-400Hz 4�2W

Operating Temp�: �� 0 to 50°C

Storage Temp:�� –20°C to 70°C

Relative Humidity:�� 95% (non condensing)

Case Dimensions:��

Bezel (4.48"x4.48") 113.8x113.8mm

Depth behind bezel (4.23") 107.46 mm

Plus (0�48”) 12�24 mm for connectors

Weight:�� 16 oz�, 1lb 4 oz when packed

Table of Contents

Bargraph Center Point Display Mode Selection .. 7

Bargraph Color Programming Mode ...... 10

Case Dimensions....................... 8

Component Layout .................... 12

Connector Pinouts ..................11-12

Controls and Indicators ................. 2

Decimal Point and Brightness Selection .... 6

Digital Span Selection for Bargraph Display . 6

Programming Conventions ............... 2

Setpoint Setting & Relay Conf. Mode ....9-10

Software Features ...................... 1

Software Logic Tree .................... 3

Specifications ......................... 1

Successive Digital Rescaling ....................5

Two Point Analog Range Setting & Calibration ... 8

Digital Span Selection for Analog Range Output . 7

Functional Diagram .................... 11

General Features ....................... 1

I-Series Input Signal Conditioning Modules ..13-15

Input Module Calibration Procedures ..... 17

Input Module Component Glossary ....... 16

Ordering Information ................... 19

Pin Descriptions ...................... 11

Page 2 CL-B101D40PS Manual (d0096)

Front Panel Buttons

Program Button

The

button is used to move from one program step to the next.

When pressed at the same time as the button, it initiates the

calibration mode. When pressed at the same time as the but-

ton, it initiates the setpoint setting mode.

101 Segment

Bargraph

Up Button

When in the operational display, pressing the button allows you

to view the setting of the saved Peak and Valley Values.

When setting a displayed parameter during programming, the

button is used to increase the value of the displayed parameter.

Down Button

When in the operational display, pressing the button allows you

to change the Brightness Level as well as to view the setting of

the setpoints SP1, SP2, SP3 & SP4.

When setting a displayed parameter during programming, the

button is used to decrease the value of the displayed parameter.

Front Panel LED Display

Annunciator LEDs

The annunciator LEDs indicate the alarm status. They are labeled

from bottom to top: SP1, SP2, SP3, SP4.

Digital LED Displays

The digital LED displays are used to display the meter input

signal readings. They also display the programming settings

during programming.

Setpoint Indication

The position of setpoints on the bargraph display are indicated by

an ON or OFF segment dependent on the bargraph display being

above or below the setpoint.

Setpoints

indicated

by an ON

Segment

Setpoints indicated

by an OFF Segment

Controls and Indicators

This symbol represents the

OPERATIONAL DISPLAY.

This is the PROGRAM button.

This is the UP button.

This is the DOWN button.

When a button is shown, press and

release it to go onto the next step in the

direction indicated by the arrow. When

an alternative dotted line is shown, this

indicates that an alternative logic branch

will be followed when a particular option

is present.

When two buttons are shown side by side

and enclosed by a dotted line, they must

be pressed at the same time then released

to go onto the next programming step.

If an X appears through a digit, it means that

any number displayed in that digit is not rel-

evant to the function being explained.

[Span]

[10000]

When the

and

buttons are shown

together, the display value can be increased

by pressing and releasing the

button

or decreased by pressing and releasing the

button.

When the

and

buttons are shown

with two displays, either display can be

selected by pressing and releasing the

buttons.

When two displays are shown together

with bursts, this indicates that the display is

toggling (flashing) between the name of the

function and the value.

Text or numbers shown between square

brackets in a procedure indicate the pro-

gramming code name of the function or the

value displayed on the meter display.

When there are more than two display selec-

tions they are shown in brackets below the

first display and are also selectable by

pressing and releasing the

buttons.

A dotted line enclosing an entire logic dia-

gram indicates that programming branch

will appear only when a particular option is

present.

To explain software programming procedures, logic diagrams are

used to visually assist in following the programming steps. The

following symbols are used throughout the logic diagrams to

represent the buttons and indicators on the meter:

Programming Conventions

[X•XXX]

[XX•XX]

[XXX•X]

[XXXX•]

[XXXX]

Front Panel Controls and Indicators

LED

Annunciators

for Setpoints

1-4

Single or

Tri-color

Bargraaph

Display

Button

DOWN

Button

PROGRAM

Button

7 Segments

Digital

Display

CL-B101D40PS Manual (d0096) Page 3

Software Logic Tree

The CL-B101D40PS is an intelligent bargraph meter with a hier-

archical software structure designed for easy programming and

operation, as shown below in the software logic tree.

Peak

Reset

PEAK

Reset

VA LY

Valley

[orAn]

[rEd]

NOTE: Will only

appear if a tricolor

display is installed

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

BARGRAPH COLOR

PROGRAMMING MODE

See Page 9

Tricolor Bargraph

The tri-color bargraph is designed

like a traffic light, to display either

red, orange or green, but only one

color at a time. The color to be

displayed is selected in two ways.

The first step is to select the color

to be displayed when the bar is

“below” whichever set point is set to

the lowest position.

The second step is to select the

color to be displayed when the bar

is above each specific setpoint,

regardless of the order or position

to which the set points are set.

However, if two or more setpoints

with differently specified colors are

positioned at the same set point

value, the color specified for the set

point with the highest identifying

number will be displayed. When

setpoints are set to the same value,

the SP4 color overrides the SP3

color, the SP3 color overrides the

SP2 color, and the SP2 color

overrides the SP1 color.

[rLYS] (h) High

the relay

energizes

when the

setpoint is

exceeded.

(L) Low

the relay

energizes below

the setpoint.

(–) Disabled

the relay will be

diabled and

removed from

the menu.

Pump On Pump Off

When PUM is selected ON,

and SP2 is set at a value

higher than SP1, the SP1

relay will operate in

a special "pump on pump off"

Hysteresis mode. SP2 acts

as the upper limit and SP1

acts as the lower limit of the

Hysteresis Band.

For filling applications, rLYS

should be set to LhLh. SP1 will

then activate for inputs less than

the SP1 setpoint, and remain

ON until the SP2 setpoint is

reached.

For emptying applications,

rLYS should be set to hhhh.

SP1 will then activate for inputs

greater than the SP2 setpoint,

and remain ON until the SP1

setpoint is reached.

Operational Display

MAIN MENU

PEAK & VALLEY

VIEW & RESET

BRIGHTNESS AND

SETPOINT VIEW MODE

Bargraph Center Point

Display Selection (cto)

This branch will

only appear if

the analog

output option

is installed

Back to

Operational

Display

Digital Display

ON/OFF

Selection (diSP)

Sub-menu MODE

Calibration

Input

Calibration

Output

Calibrate Analog

Output Lo

Calibrate Analog

Output Hi

Select the Digital

Reading at which

the Analog Output

Hi (chi) will occur

Select the Digital

Reading at which

the Analog Output

Lo (cLo) will occur

This branch will only

appear if the analog

output option

is installed

DIGITAL SPAN SELECTION

FOR ANALOG RANGE OUTPUT

See Page 6

DIGITAL DISPLAY ON/OFF

See Page 6

BARGRAPH CENTER POINT

DISPLAY MODE SELECTION

See Page 6

TWO POINT ANALOG OUTPUT

RANGE SETTING AND CALIBRATION

See Page 7

Set the Decimal

Point (dp)

Bargraph Display

Scale Lo Range

Setting (bLo)

Bargraph Display

Scale hi Range

Setting (bhi)

[X•XXX]

[XX•XX]

[XXX•X]

[XXXX•]

[XXXX]

DECIMAL POINT AND

BRIGHTNESS SELECTION

See Page 5

DIGITAL SPAN SELECTION

FOR BARGRAPH DISPLAY

See Page 5

Goes directly

to Zero setting

if Analog Output

is not installed

–

4.00

–

20.00

1 Dimmest

2 Dim

3 Bright

4 Brightest

SETPOINT SETTING AND

RELAY CONFIGURATION MODE

See Page 8

L, h or –

Relay Activation

& Relay Disable

PROGRAMMABLE

OFFSET AND

SCALE FACTOR

See Page 4

Offset

Scale

Factor

Delay-on-Make

[doM]

Delay-on-Break

[dob]

0 to 9999

seconds

0 to 9999

seconds

Set Setpoint 1

[SP1]

Delay-on-Make

[doM]

Delay-on-Break

[dob]

0 to 9999

seconds

Setpoint 2

[SP2]

0 to 9999

seconds

Pump

[PUM]

Hysteresis

[hYSt]

Hysteresis

[hYSt]

Hysteresis

[hYSt]

Hysteresis

[hYSt]

Setpoint 3

[SP3]

Setpoint 4

[SP4]

This branch will only

appear if the Programming

Lock is engaged

This branch will only appear if the

Programming Lock is engaged.

When Lock is engaged, values

can be viewed, but not changed.

Calibration

Mode

vWhen power is applied, all segments of the bargraph and

digital display light up for 3 seconds. The version number of

the installed software is then displayed for 2 seconds, after

which, the operational display indicates the input signal.

15 Second Program Timeout

Except for ZERO and SPAN settings in the Two Point Digital Calibration

Mode and the Analog Output Range Setting and Calibration Mode (cLo and

chi), the meter has a 15 second program timeout. If no buttons are pressed

for 15 seconds in any of the other programming sequences, the meter will

exit the programming mode and return to the operational display. Any pro-

gram changes that were made prior to pressing the

button in the preced-

ing step will not be saved.

Page 4 CL-B101D40PS Manual (d0096)

STEP A Enter the Calibration Mode

1) Press the

and buttons at the same time. Display

toggles between [CAL] and [oFF].

Press the or button. Display changes from [oFF] to

[on].

Press the

button. Display toggles between [CAL] and

[out].

Note: If at this point, the display skips directly to STEP C and toggles

between [ScAL] and the previous [ScAL] setting, the software

is detecting that the optional analog output hardware is NOT

installed.

STEP B Select Two Point Digital Calibration of Input Signal

1) Press the or button to select CAL [iP] for input signal

calibration.

2) Press the

button. Display toggles between [oFFS] and the

previous offset setting.

STEP C Set the Offset on the Digital Display

1) Using the and buttons, adjust the digital display to

the desired offset. This is the reading that the meter will dis-

play for a zero input

2) Press the

button. Display toggles between [ScAL] and

the previous Scale factor.

STEP D Set the Scale factor on the Digital Display

Using the and buttons, adjust the meter display to

the desired Scale factor. The default value is 2000, for which a

2V input will read 2000. If the scale factor is changed the

display will change proportionately. Therefore if the Scale

factor is changed to 1000 then for the same 2V input the dis

play would read 1000.

2) Press the

button.

The Digital Rescaling is now complete.

If the Digital Rescaling was successfully completed, the

menu branches to the Digital Span Selection for Bargraph

Display (see page 6), and the display flashes [bhi] and the

previous setting.

The CL-B101D40PS Manual (d0096) meter may be rescaled without applying an external signal by changing the Offset and Scale

factor.

Offset is the reading that the meter will display for a zero input. The Offset may be set to any value from -1999 to +9999. The

default value of the Offset is 000

Scale factor is the gain of the meter. The displayed reading is directly proportional to the Scale factor. The default value of the

scale factor is 2000, but it may be set to any value between -1999 and +9999.

For an input of 2V a calibrated meter will read 2000 with the default Scale factor of 2000, 3000 with a Scale factor of 3000 and

500 with a Scale factor of 500

If a linear scale is represented by mx + b, then the Scale Factor corresponds to the slope ‘m’ and the Offset corresponds to

the intercept ‘b’

The internal Signal Span is limited to 3 V DC between – 1 V DC to + 2 V DC. Outputs from an Input Signal Conditioning module

that exceed these limits will cause the meter to indicate overrange.

Note: Most input signal conditioners have provisions for analog calibration and scaling. If the meter’s digital Scale Factor is

set to 2000 and Offset set to 0000 then, any pre-calibrated signal condi-

tioner with an output that does not exceed – 1 V to + 2 V, will read correct-

ly in the meter without any further calibration.

Digital Rescaling

Digital Rescaling Procedure

MAIN MENU

Operational Display

Sub-menu

MODE

STEP A Calibration

Mode

STEP B Calibration

Mode

STEP C Offset

STEP D Scale

Factor

To Digital Span Selection for

Bargraph Display Page 6

cAL out/iP branch will only

appear if the analog output

option is installed, otherwise

cAL on goes directly to ZEro

setting

DIGITAL

RESCALING MODE

To Digital Span Selection

for Bargraph Display

See Page 7

To Two Point Analog

Output Range Setting

and Calibration

See Page 8

CL-B101D40PS Manual (d0096) Page 5

Successive Digital Rescaling to get Progressively Better Accuracy

Hopper contains some material

whose EXACT weight is not known.

It is estimated to be 320 pounds.

When a Texmate meter is connected,

it displays 300 instead of 320.

3.5mV

300

Texmate Meter

Offset = 0

Scale = 2000

STEP A

Change offset to +20 to correct the

Texmate meter display to 320.

3.5mV

Texmate Meter

Offset = 20

Scale = 2000

320

STEP B

A known load of EXACTLY 1000

pounds is now added to the hopper.

Texmate meter displays 1190 instead

of 1320.

13.5mV

Texmate Meter

Offset = 20

Scale = 2000

1190

STEP C

Change scale to 2219 to correct the

Texmate meter display to 1320

New scale = 2000 x 1320 / 1190

= 2219

The meter is approximately cali-

brated. Approximate, not exact,

because the weight in STEP B is not

exactly known.

13.5mV

Texmate Meter

Offset = 20

Scale = 2219

1320

STEP D

Later (maybe many days later) when

the hopper is finally empty, it is seen

that the meter does not read zero.

0.5mV

Texmate Meter

Offset = 20

Scale = 2219

STEP E

Change Offset to -40 to correct the

Texmate meter display.

Display is now correct.

0.5mV

Texmate Meter

Offset = -40

Scale = 2219

STEP F

If a known weight of 1000 pounds is

now added, the Texmate meter dis-

plays 970 instead of 1000.

error = 30 pounds

10.5mV

Texmate Meter

Offset = -40

Scale = 2219

970

STEP G

Change Scale to correct this display.

New Scale = 2219x1000 / 970

=2287

10.5mV

Texmate Meter

Offset = -40

Scale = 2287

1000

STEP H

The next time the hopper is

empty, it will read 0 correctly.

5mV

Texmate Meter

Offset = -40

Scale = 2287

STEP I

Page 6 CL-B101D40PS Manual (d0096)

Example

From Two Point

Digital Calibration

Mode See Page 4

STEP A

STEP B

STEP C

STEP D

See Example Above

of Bargraph Display

Scale Range

To Digital Span Selection

for Analog Range Output or

Bargraph Center Point

Display Mode Selection

on Page 6

DIGITAL SPAN SELECTION

FOR BARGRAPH DISPLAY

[X•XXX]

[XX•XX]

[XXX•X]

[XXXX•]

[XXXX]

DECIMAL POINT AND

BRIGHTNESS SELECTION

STEP A Enter the Calibration Sub Menu Mode

1) Press the

and buttons at the same time. Display toggles

between [CAL] and [oFF].

2) Press the

button. Display toggles between [bhi] and the

previous setting.

STEP B Set the Digital Span of the Bargraph Display

(See example

above)

1) Using the and buttons, adjust the display to the

desired high parameter reading, e.g. 6000 counts.

2) Press the

button. Display toggles between [bLo] and the

previous setting.

3) Using the and buttons, adjust the display to the

desired low parameter reading, e.g. 4000 counts.

4) Press the

button. Display changes from [4000] to [dP].

STEP C Set the Decimal Point

1) Using the and buttons, adjust the display to the

desired decimal point setting.

2) Press the

button. Display toggles between [br] and the

previous brightness setting.

STEP D Set the Bargraph and Digital Display Brightness

1) Using the and buttons, adjust the display to the

desired brightness setting (4 is the brightest setting).

2) Press the

button. Display toggles between [Anhi] and

the previous [Anhi] setting.

Note: If at this point, the display skips directly to STEP G and toggles

between [Cto] and [oFF], the software is detecting that the optional analog

output hardware is NOT installed.

Digital Span Selection For Bargraph Display

Decimal Point and Brightness Selection

Bargraph does not light

up for Input Signals up to

3999 counts

Bargraph lights up for

Input Signals above

4000 counts

Bar

High

Bar

Low

Bar

High

Bar

Low

25 75

100

25 75

100

No bargraph display

Digital display

No bargraph display

Digital display

An example of setting the

digital span of the bargraph

display to be different than

the digital display range

The bargraph can be set to display full scale (0-101 bars) any portion

of the digital reading from a minimum of 100 counts to a maximum of

12,000 counts. This provides higher resolution bargraph indication for

those applications where the normal operating input signal range is less

than the desired full scale display range of the digital display.

For Example:

If the full scale range of the meter has been set from -1999 to

9999 (0-12,000 counts), but the normal operating range of the

input signal is between 4000 & 6000. The bargraph high parame-

ter [bhi] can be set to 6000 and the bargraph low parameter [bLo]

can be set to 4000.

This means that although the meter could digitally display a signal

from -1999 to 9999 (0-12,000 counts), the bargraph display only

begins to function at a reading of 4000, and reaches full scale

indication at a reading of 6000. Although the digital display will

continue reading up to 9999 before indicating overrange, the bar-

graph display will indicate its overrange by flashing for readings

above 6000.

CL-B101D40PS Manual (d0096) Page 7

Example of Using the Center Point Bargraph Display Mode

with a Unipolar Input

If the meter's full scale range is set to 5000 counts, the midpoint would

be 2500 counts. If a signal of 2500 counts is applied only one segment at

the 2500 count mark will light up. If a signal of 4000 counts is applied the

segments between the center segment (2500 counts) and the 4000 count

mark light up.

If a signal of 1000 counts is applied, the segments between the center seg-

ment (2500 counts) and the 1000 count mark will light up.

Example of Using the Center Point Bargraph Display Mode

with Bipolar Signal Inputs

The meter may also be calibrated to display symmetrical bipolar signals such

as ± 1 V or ± 10 V. When the center point display mode is selected, it will

then function as a center zero meter. When positive signals are applied, the

bar will go up from the center point, and when negative signals are applied,

the bar will go down from the center point.

STEP E Selecting the [Anhi] Digital Value for Analog High Output

1) Using the and buttons, adjust the display to the desired

digital value at which the [chi] Calibrated Analog High output will

occur. For digital readings outside the digital span selected, the

analog output will linearly rise above the value set for chi, up to the

maximum analog output capability. However, the analog output will

not go lower than the calibrated value set for cLo (see below).

2) Press the

button. Display toggles between [AnLo] and

previous [AnLo] setting.

STEP F Selecting the [AnLo] Digital Value for Analog Low Output

1) Using the and buttons, adjust the display to the desired

digital value at which the [cLo] Calibrated Analog Low output will

occur. For Digital readings outside the Digital Span selected, the

analog output will not go lower than the calibrated value set for

cLo.

2) Press the

button. The display toggles between [cto] and

[oFF].

Note: Any two digital span points from –1999 to 9999 can be selected. The digital

values for [Anhi] analog high and [AnLo] analog low can be reversed to provide a 20 to

4mA output. The digital span selected can be as small as two counts, when using the

analog output to function as a Control or Alarm Driver. Small digital spans will cause

the high resolution 16 bit D to A to increment digitally in stair case steps.

Digital Span Selection for Analog Range Output

Bargraph Center Point Display Mode Selection

STEP G

Bargraph Center Point Mode Selection (See example above)

1) To select bargraph center point mode, press the or

button. Display changes from [oFF] to [on].

2) Press the

button. Display toggles between [diSP] and

[on] or [oFF].

STEP H Digital Display ON/OFF Selection

1) To set the display to [oFF], press the or button.

Display toggles between [diSP] and [oFF].

2) Press the

button. The display exits the calibration mode

and returns to the operational display. Only the bargraph

display is on and the digital display is off.

If the digital display is selected to be off, pressing any button to

make programming changes or to view setpoints activates the digital display.

When the procedure is complete, the digital display will then automatically

switch off.

The Display/Bargraph settings are now complete.

Operational Display

STEP G

STEP H

See Example of Bargraph

Center Point Display Mode

Selection Above

From Digital Span Selection

for Analog Range Output Above

or Direct From Decimal Point

and Brightness Selection Page 5

if Analog Output Option is Not Present

BARGRAPH CENTER POINT

DISPLAY MODE SELECTION

STEP E

STEP F

This branch will only

appear if the analog

output option is installed

To Bargraph Center

Point Display Mode

Selection Below

From Decimal Point and

Brightness Selection

See Page 5

DIGITAL SPAN SELECTION

FOR ANALOG RANGE OUTPUT

-1V +1V

0.800

-0.800

-1V +1V

Center Point

Single Bar Lit

Center Point

As signal

increases

Digital display

Center Point

As signal

decreases

Digital display

05000

5000

2500

4000

5000

2500

1000

Center Point

Single Bar Lit

Center Point

As signal

increases

Digital display

Center Point

As signal

decreases

Digital display

Unipolar Signal Input Bipolar Signal Input

Page 8 CL-B101D40PS Manual (d0096)

101.60

4.000

42.85

1.687

42.85

1.687

42.85

1.687

42.85

1.687

6.50

0.256

113.79

4.480

113.79

4.480

56.90

2.240

56.90

2.240

17.50

0.689

97.77

3.849

119.70

4.713

13.70

0.539

1/4"-28UNF

Panel Cutout

5.0

0.197

0.157

16.30

0.642

13.70

0.539

4.80

0.189

screw-10-32 UNF

0.315

0.276

16.30

0.642

13.70

0.539

2.60

0.102

6.32

0.249

screw-1/4”-28 UNF

Case Dimensions

Operational Display

Sub-menu

MODE

STEP A Calibration

Mode

STEP B Calibration

Mode

STEP E

Calibrate

Analog

Output

STEP F

Calibrate

Analog

Output

Will only appear if the analog

output option is installed

To Digital Span Selection

for Bargraph Display

See Page 5

To Two Point Digital

Calibration Mode

See Page 4

Operational Display

TWO POINT ANALOG OUTPUT

RANGE SETTING AND CALIBRATION

–x

4.00

–x

20.00

Determine if the Analog Output Selection Header is in the 4 to 20mA (0-20mA) position or the 0

to 10VDC position. If necessary, the module may have to be removed and the header position

changed (see Component Layout below).

Note: Always disconnect power from the meter before removing the analog output module to

adjust the mA or Volts output selection header and reinstalling it. When power is reconnected, the

meter’s software will automatically detect the presence or absence of the analog output module.

STEP A Enter the Calibration Mode

1) Press the

and buttons at the same time. Display toggles between [cAL] and [oFF].

2) Press the or button. Display changes from [oFF] to [on].

3) Press the

button. Display toggles between [cAL] and [out] input calibration.

Note: If at this point the display skips directly to toggle between Zero and the previous Zero

setting, the software is detecting that the optional analog output hardware is NOT installed.

STEP B

Enter the Two Point Analog [ouT] Output Range Setting and Calibration Mode

1) Press the

button. Display toggles between [cLo] and an internal scale factor.

STEP E Set or Calibrate [cLo] the Low Analog Value of the Analog Output Range

1) Connect a multimeter to analog output pins 17 and 18 (see Rear Panel Pinouts

on page 10). Using the and buttons, adjust the analog output to the desired

low value as measured on the multimeter. cLo may be adjusted to any value from

–0.3 mA to 18 mA (mA output selected) or from –0.6 V to 8 V (volt output selected).

However, the output of cLo must always be less than the value selected for chi. If

a reversed analog output is desired, the values selected to establish the Digital

Span can be reversed (see top of page 6). For digital readings outside the Digital

Span selected, the analog output will not go any lower than the calibrated value set

for cLo. However, the analog output will linearly rise above the value set for chi, up

to the the maximum analog output capability (see chi below).

2) Press the

button. Display toggles between [chi] and an internal scale factor.

STEP F Set or Calibrate [chi] the High Analog Value of the Analog Output Range

1) Using the and buttons, adjust the analog output to the desired high value

as measured on the multimeter display. chi may be adjusted to any value from 18

mA to 24 mA (mA output) or from 8 V to 10.3 V (volt output). However, the value

must be higher than the value selected for cLo. For digital readings outside the

Digital Span selected, the analog output will linearly rise above the value set for chi,

up to the maximum analog output capability.

2) Press the

button. The meter exits the calibration mode and returns to the

operational display.

Note: The analog output range established by the values selected for cLo and chi will occur, auto-

matically scaled, between the two digital values selected for AnHi and AnLo. However,

the analog

output can linearly rise above the chi value set for digital readings outside the digital span

selected. See Digital Span Selection on page 6.

Two Point Analog Output Range Setting and Calibration

CL-B101D40PS Manual (d0096) Page 9

Operational Display

SETPOINT SETTING

AND RELAY

CONFIGURATION MODE

STEP A

STEP B

STEP C

STEP D

No [doM] or [dob]

STEP E

STEP F

STEP G

STEP H

STEP I

STEP J

STEP K

STEP L

To Step M of Setpoint

Setting and Relay

Configuration Page 9

The following programming steps are required to enter the setpoint values and configure the relay functions

in a meter with four relays using four setpoints. Generally if less than four relays are installed, the setpoints

without relays are operational in software for tri-color control or display only purposes. To remove unwanted

setpoint indications, set them to 9999 or -1999 depending on the relay activation mode selected.

STEP A Enter the Setpoint Mode

1) Press the

and buttons at the same time. Display toggles between [SP1] and the previous

SP1 setting.

STEP B Set Setpoint 1 [SP1]

1) Using the and buttons, adjust the display to the desired SP1 value.

2) Press the

button. Display toggles between [doM] and the previous [doM] setting.

STEP C Set the SP1 Delay-on-Make [doM] Delay Time Setting

Using the and buttons, adjust the display to the desired [doM] value (0 to 9999 seconds).

The reading must continuously remain in an alarm condition until this delay time has elapsed before

the relay will make contact (energize).

2) Press the

button. Display toggles between [dob] and the previous [dob] setting.

STEP D Set the SP1 Delay-on-Break [dob] Delay Time Setting

Using the and buttons, adjust the display to the desired [dob] value (0 to 9999 seconds).

The reading must continuously remain in a non-alarm condition until this delay time has elapsed

before the relay will break contact (de-energize).

2) Press the

button. Display toggles between [hYSt] and the previous [hYSt] setting.

STEP E Select the Hysteresis [hYSt]

Using the and buttons, select the Hysteresis to be ON or OFF.

2) Press the

button. Display toggles between PUM and (on) or (oFF).

STEP F Select Pump [PUM] (on) or (oFF)

Using the and buttons, select the Pump to be ON or OFF. When PUM is selected ON, and

SP2 is set at a value higher than SP1, the SP1 relay will operate in a special "pump on pump off" mode.

SP2 acts as the upper limit and SP1 acts as the lower limit of the Hysteresis Band on the SP1 relay.

For filling applications:

[rLYS] should be set to [LhXX] (see step M). The SP1 relay and SP1 LED Annunciator will then activate for inputs

less than the SP1 setpoint, and remain ON until the SP2 setpoint is reached.

For emptying applications:

[rLYS] should be set to [hhXX] (see step M). The SP1 relay and SP1 LED Annunciator will then activate for inputs

greater than the SP2 setpoint, and remain ON until the SP1 setpoint is reached.

2) Press the

button. Display toggles between [SP2] and the previous SP2 setting.

STEP G Set Setpoint 2 (SP2)

1) Using the and buttons, adjust the display to the desired SP2 value.

2) Press the

button. Display toggles between [hySt] and the previous [hySt] setting.

STEP H Select the Hysteresis [hYSt]

Using the and buttons, select the Hysteresis to be ON or OFF.

2) Press the

button. Display toggles between [SP3] and the previous [SP3] setting.

STEP I Set Setpoint 3 (SP3) (No [doM] or [dob])

1) Using the and buttons, adjust the display to the desired SP3 value.

2) Press the

button. Display toggles between [hySt] and the previous [hySt] setting.

STEP J Select the Hysteresis [hYSt]

Using the and buttons, select the Hysteresis to be ON or OFF.

2) Press the

button. Display toggles between [SP4] and the previous [SP4] setting.

STEP K Set Setpoint 4 (SP4) (No [doM] or [dob])

Using the and buttons, adjust the display to the desired SP4 value.

2) Press the

button. Display toggles between [hySt] and the previous [hySt] setting.

STEP L Select the Hysteresis [hYSt]

Using the and buttons, select the Hysteresis to be ON or OFF.

2) Press the

button. Display toggles between [rLYS] and the previous relay setting.

Please Continue On Next Page.

Setpoint Setting and Relay Configuration Mode

Page 10 CL-B101D40PS Manual (d0096)

STEP M

STEP N

STEP O

STEP P

STEP Q

STEP R

STEP S

STEP T

STEP U

[orAn]

[rEd]

NOTE: Will only

appear if a tricolor

display is installed

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

[orAn]

[rEd]

BARGRAPH COLOR

PROGRAMMING MODE

Operational Display

From From Step L of

Setpoint Setting and Relay

Configuration Page 8

L or h

To comply with the latest safety requirements, the tri-color bargraph is designed like a traffic light, to

display either red, orange or green, but only one color at a time. When the bar reaches a selected

color change point, the entire bar will change to the color designated for that zone. This eliminates any

ambiguity as to the signal status, especially just after transitioning to a new zone.

First (Step Q) is to select the color to be displayed, when the bar is “below*”, whichever set point is set

to the lowest position.

Second (Steps R, S, T, and U) is to select the color to be displayed when the bar is above each specific

set point, regardless of the order or position to which the set points are set.

However, if two or more setpoints with differently specified colors are positioned at the same set point

value, the color specified for the set point with the highest identifying number will be displayed. When

set points are set to the same value, the SP4 color overrides the SP3 color, the SP3 color overrides the

SP2 color, and the SP2 color overrides the SP1 color.

STEP Q Select Bargraph Color when the bar is BELOW* the Setpoint that is set to the lowest

position