Textron GREENLEE CMGRT-100A Bedienungsanleitung

CMGRT-100A

CLAMP-ON GROUND

RESISTANCE TESTER

VERIFICADOR

DERESISTENCIA DE

TIERRA CON PINZA

VERIFICATEUR DE

RESISTANCE DE TERRE A

PINCE

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

MANUEL D'INSTRUCTIONS

Read and understand all of the instructions and safety information in this

manual before operating or servicing this tool.

Lea y entienda todas las instrucciones y la información sobre seguridad

que aparecen en este manual, antes de manejar esta herramienta o

darle mantenimiento.

Lire attentivement et bien comprendre toutes les instructions et les

informations sur la sécurité de ce manuel avant d'utiliser ou de procéder

à l'entretien de cet outil.

Español: p. 33

Français: p. 65

MEM

OFF

+ A

SET-UP

HOLD

www.calcert.com [email protected]1.800.544.2843 0

Table of Contents

Description .............................................................................................................3

Safety .....................................................................................................................3

Purpose...................................................................................................................3

Important Safety Information..............................................................................4–6

Identiﬁcation...........................................................................................................7

Symbols on Unit ..............................................................................................7

Display Icons ..........................................................................................................8

Product Features ..............................................................................................9–22

Rotary Switch Positions ..................................................................................9

Alarm Feature and Set-up.............................................................................10

Navigation .....................................................................................................10

Set-up Menus..........................................................................................11–19

Memory .........................................................................................................22

Auto-Power Off..............................................................................................22

Measurement Mode ......................................................................................22

Theory of Operation..............................................................................................23

Operation..............................................................................................................24

Typical Applications........................................................................................25–27

Frequently Asked Questions .................................................................................28

Accuracy.........................................................................................................28–29

Speciﬁcations.......................................................................................................30

Overvoltage Installation Categories......................................................................30

Maintenance.........................................................................................................31

Battery Replacement............................................................................................31

www.calcert.com [email protected]1.800.544.2843 0

CMGRT-100A

Description

The Greenlee CMGRT-100A Clamp-On Ground Resistance Tester is a hand-held testing device intended to

evaluate grounding systems. It has two modes:

• Standard Mode: Standard Loop Resistance & Leakage Current Measurements

• Advanced Mode: Reﬁne Measurements to ﬁnd Impedance at the Selected Frequency & to compute

Contact Voltage

Furthermore, it can also give an idea about the integrity of the ground systems, the quality of connections or

bonds within the system.

The tester can measure Loop Resistance in the range of 0.01 Ω to 1500 Ω as well as leakage current in the

range of 0.2 mA to 40A. It comes with a data storage function, that can log up to 300 measurements (Both

Ω and/or A). Furthermore, the meter also allows the user to select test frequency between 50, 60, 128,

or 2083 Hz.

Safety

Safety is essential in the use and maintenance of Greenlee tools and equipment. This instruction manual and

any markings on the tool provide information for avoiding hazards and unsafe practices related to the use of

this tool. Observe all of the safety information provided.

Purpose

This instruction manual is intended to familiarize all personnel with the safe operation and maintenance

procedures for the Greenlee CMGRT-100A Clamp-On Ground Resistance Tester.

Keep this manual available to all personnel.

Replacement manuals are available upon request at no charge.

Greenlee and are registered trademarks of Greenlee Textron.

KEEP THIS MANUAL

Do not discard this product or throw away!

All speciﬁcations are nominal and may change as design improvements occur. Greenlee Textron Inc.

shall not be liable for damages resulting from misapplication or misuse of its products.

® Registered: The color green for electrical test instruments is a registered trademark of

TextronInnovations Inc.

www.calcert.com [email protected]1.800.544.2843 0

Important Safety Information

Read and understand this material before operating or servicing this

equipment. Failure to understand how to safely operate this tool can result in

an accident causing serious injury or death.

This symbol is used to call your attention to hazards or unsafe practices which could result in an

injury or property damage. The signal word, deﬁned below, indicates the severity of the hazard. The

message after the signal word provides information for preventing or avoiding the hazard.

SAFETY ALERT SYMBOL

Immediate hazards which, if not avoided, WILL result in severe injury or death.

Hazards which, if not avoided, COULD result in severe injury or death.

Hazards or unsafe practices which, if not avoided, MAY result in injury or property damage.

Electric shock hazard:

Contact with live circuits can result in severe injury or death.

www.calcert.com [email protected]1.800.544.2843 0

CMGRT-100A

Important Safety Information

Electric shock and ﬁre hazard:

• Do not expose this unit to rain or moisture.

• Do not use the unit if it is wet or damaged.

• Clamp meter, test leads or any other clamp accessory, when used to make a measurement, create a System.

The System is rated for CAT IV 600 VAC when using the test leads or accessories provided with the meter.

The System CAT and voltage rating is limited by the lowest rated component in the System when using test

leads or accessories not provided with the meter.

• Inspect the test leads or accessory before use. They must be clean and dry, and the insulation must be in

good condition. Do not use the test lead if the contrasting inner layer of insulation is visible.

• Use this unit for the manufacturer’s intended purpose only, as described in this manual. Anyotheruse can

impair the protection provided by the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Do not operate with the case open.

• Before opening the case, remove the test leads from the circuit and shut off the unit.

• Keep hands and ﬁngers below the barriers on the test leads and the clamp meter body.

Failure to observe these warnings could result in severe injury or death.

www.calcert.com [email protected]1.800.544.2843 0

Electric shock hazard:

• Unless measuring voltage, current, or frequency, shut off and lock out power. Make sure that all capacitors

are discharged. Voltage must not be present.

• Set the selector and connect the test leads so that they correspond to the intended measurement. Incorrect

settings or connections can result in incorrect measurements or damage to the unit.

• Using this unit near equipment that generates electromagnetic interference can result in unstable or inaccu-

rate readings.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Do not change the measurement function while the test leads are connected to a component or circuit.

• Do not clamp the jaw around a conductor carrying a frequency greater than 400Hz. The magnetic circuitry

may reach a hazardous temperature if this frequency is exceeded.

Failure to observe these precautions may result in injury and can damage the unit.

Electric shock hazard:

• Do not attempt to repair this unit. It contains no user-serviceable parts.

• Do not expose the unit to extremes in temperature or high humidity. Refer to “Speciﬁcations.”

Failure to observe these precautions may result in injury and can damage the unit.

Important Safety Information

www.calcert.com [email protected]1.800.544.2843 0

CMGRT-100A

Identiﬁcation

1. Jaw

2. Guard

3. Lever

4. Rotary Switch

5. Display Backlight ON/OFF

6. Stores Measurements in Memory

7. Navigate/Validate Measurement Displays

8. HOLD Button

9. OLED Display

10. Calibration Loop (52084190)

Symbols on the Unit

Warning—Read the

instruction manual

Warning—Risk of Electric Shock

Double insulation

Application around or removal from

hazardous live conductors is permitted

Recyclable in accordance with

ISO 14040 standard

MEM

OFF

+ A

SET-UP

HOLD

www.calcert.com [email protected]1.800.544.2843 0

Display Icons

11. Advance Mode

12. Inductive Component = Resistive Component (Advanced Mode)

13. Main Display. Displays OR (Out of Range) when the measured

resistance is over 1500 Ω or/and when the measured current is over 40A

14. Resistance/Impedance (Advanced Mode)

15. Storage Mode

16. Memory Recall Mode

17. Memory Location

18. Hazardous Voltage (Blinks when Voltage exceeds 50V)

19. Alarm Threshold High/Low Indicator

20. Alarm Threshold Display

21. Units of Alarm Displayed

22. Units of Main Display

23. Units of Top Display (Loop Inductance/ Current)

24. Top Display (Advanced Mode)

25. Low Battery

26. Auto Power Off Disabled

27. Open Jaw

28. Presence of Stray Noise (Current) In Loop

(Measurements not valid)

29. Main Display Indicates Date When Lit

30. Freeze Measurement

31. Speaker Enabled

11 24

12 23

2829

www.calcert.com [email protected]1.800.544.2843 0

CMGRT-100A

Product Features

Rotary Switch Positions:

OFF – Instrument Powered Off

Ω + A – Measure Loop Impedance & Leakage Current

A– Measure Current

MR – Display Stored Data

SET-UP – Access to Instrument settings & Data Selection

Alarm Feature:

There are four distinct patterns of audio signal being employed for various warnings and instrument

operations. They can be disabled if required. The different pattern and their purposes are listed below:

Low – pitched with short intervals:

Normal instrument operations

Low – pitched with a permanent signal:

Alarm thresholds triggered for either Ω or A

High – pitched with a short intervals:

Irregular occurrence which may include OR in measurements or a full memory

High – pitched with a permanent signal:

Alarm threshold for V triggered

Thresholds are user deﬁned values. The alarm is enabled with a user deﬁned threshold when or when

icons are displayed.

– Alarm Enabled for measurement above deﬁned threshold

– Alarm Enabled for measurement below deﬁned threshold

MEM

OFF

+ A

SET-UP

HOLD

www.calcert.com [email protected]1.800.544.2843 0

Instrument SET-UP

There are twelve accessible menus in the SET-UP position of the rotary switch that allows user deﬁned

parameters to conﬁgure the instrument.

Navigation

Navigating through the features is made possible using the following buttons on the instrument:

– Move up in the menu tree

– Move down in the menu tree

– Select menu or return to previous menu

When the user enters the menu tree, the selected menu starts blinking, indicating the state of the menu.

Product Features (cont'd)

No. Function

1 Erase stored data.

2 Enables/ disable audible alarm.

3 Enables/disables Auto Power OFF

4 Sets the impedance alarm threshold (Ω)

5 Sets the voltage alarm threshold (V)

6 Sets the current alarm threshold (I)

7 Sets the date.

8 Sets the time.

9 Selects the Standard or Advanced operating mode.

10 Selects the test frequency for the impedance.

11 Enables/disables the AUTO-HOLD mode.

12 Displays the version number.

13 Not used.

www.calcert.com [email protected]1.800.544.2843 0

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Textron Prüfgeräte Handbücher

Textron

Textron GREENLEE CMT-80 Bedienungsanleitung

Textron

Textron Tempo PE945 Bedienungsanleitung

Textron

Textron HDE HISAT-25 Bedienungsanleitung

Textron

Textron Tempo Compact DSP Bedienungsanleitung

Textron

Textron GREENLEE 521A Bedienungsanleitung

Textron

Textron Greenlee CableScout TV220 Bedienungsanleitung

Textron

Textron Tempo PE945 Bedienungsanleitung

Textron

Textron Greenlee Communications PE930 Bedienungsanleitung

Textron

Textron Greenlee CM-450 Bedienungsanleitung

Textron

Textron Tempo PE961 Bedienungsanleitung

Textron

Textron Tempo PE2003 Bedienungsanleitung

Textron

Textron HDE PF-50 Bedienungsanleitung

Textron

Textron Greenlee Communications DataScout 10G Bedienungsanleitung

Textron

Textron Tempo PE930 Bedienungsanleitung

Textron

Textron HDE TAG-5000 Bedienungsanleitung

Textron

Textron Tempo 525N-60 Bedienungsanleitung

Textron

Textron Tempo 525N-30 Bedienungsanleitung

Textron

Textron HDE HI-TEST IT-4 Bedienungsanleitung

Textron

Textron HDE ClearTest CT-300 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Vernier

Vernier Go Direct Voltage Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung