The Handy S.A.M.2 Bedienungsanleitung

ITEM # 16900G - 16900O - 16900R - 16900B

1. Center load on table - 1000 lb. maximum.

2. Connect to 110 psi maximum shop air.

3. Keep safety bar in position at all times - except

when lowering.

4. Keep hands and tools from under carriage.

5. Do not mount table when in elevated position.

6. Do not ride vehicle onto lift.

7. Lift must be in the lowered position when moving.

8. Only trained persons should operate Air Lift.

9. The working area should be sufficiently lit.

10. Foot controller should be at least 3 feet away from

Air Lift during raising and lowering operation.

11. Recommended for indoor use only.

12. Tie-down straps must be used in conjunction with

the holes provided in the lift top.

S.A.M.2 1000 AIR LIFT

INSTRUCTIONS PARTS DRAWING PART LIST

UNPACKING AND SET-UP

1. Open carton, then remove ramp, drop panel and shipping boards.

2. CAREFULLY TURN TABLE UPRIGHT INTO OPERATING POSITION BEFORE REMOVING SHIPPING

CABLE RESTRAINT FROM SCISSOR MECHANISM.

3. Remove the two shipping bolts attaching rear drop panel to lift top. The bolts are located under drop

panel and lift top at each end.

4. Connect foot-operated air valve to 110 psi maximum air supply. The lift may be damaged and/or personal

injury may result if the pressure exceeds the maximum 110 psi rating.

5. Stand clear of lift table, and depress the UP side of foot valve to raise table.

6. To lower table, lift detent bar from safety latch and lower to next position or to floor.

7. To level front or rear drop panels: adjust set screws up or down through access holes in each corner of lift

top to gain level work platform. See print.

8. Slide front & rear drop panels into place and lift to lock in place at end of tube.

9. Insert ramp mounting tabs into slots at either end of table to mount ramp.

NOTE: If cycle vise is being installed, ramp must be mounted opposite the cycle vise.

OPERATION

1. Loads must be centered on table at all times. Table is rated for a maximum load of 1000 lbs.

2. Loads must be firmly positioned and secured on table at all times. Tie-down straps must be used

in conjunction with the holes provided in the lift top.

3. All moving parts have been lubricated at the factory and should be re-lubricated every 6 months to prevent

galling. Grease zerks are located at each end of frame pivot shaft and at

top ends of inside frame assembly.

4. Lightly oil cylinder rod when it becomes dry.

5. Squirt some oil through bleed hole in plate end of cylinder to lubricate piston and its seal every 6 months.

6. Pivot shaft set screws should be checked frequently to be sure they are tight. These are

located at the top end of the inside frame assembly.

OTHER OPTIONS AVAILABLE

Separate installation instructions included with each option.

14476

CV-17 CYCLEVISE–Used to stabilize motorcycle while on lift

16901

10” SIDE EXTENSIONS – ( 2) Expa nds width of lift to a full 48”

NOTE: READ ENTIRE MANUAL TO COMPLY WITH ALL SAFETY AND SERVICE PRECAUTIONS.

DEATH, PERSONAL INJURY AND/OR PROPERTY DAMAGE MAY OCCUR UNLESS INSTRUCTIONS

ARE FOLLOWED CAREFULLY.

PARTS DRAWING - PARTS LIST

Shop for other garage accessories on our website.

Inhaltsverzeichnis

Andere The Handy Hebesystem Handbücher

The Handy

The Handy 14472G Bedienungsanleitung

The Handy

The Handy S.A.M. 1000 Bedienungsanleitung

The Handy

The Handy B.U.L. Stücklistenhandbuch

The Handy

The Handy 16000G Bedienungsanleitung

The Handy

The Handy 20707G Bedienungsanleitung

The Handy

The Handy OX 1800 Bedienungsanleitung

The Handy

The Handy 16013G Bedienungsanleitung

The Handy

The Handy 16007G Bedienungsanleitung

The Handy

The Handy 10740 Datenblatt

The Handy

The Handy 21660 Bedienungsanleitung

The Handy

The Handy 16867G Bedienungsanleitung

The Handy

The Handy 16005G Bedienungsanleitung

The Handy

The Handy 10740G Bedienungsanleitung

The Handy

The Handy 10738 Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung