Thermal Dynamics CUTMASTER 81 Bedienungsanleitung

PLASMA CUTTING SYSTEM

81 CUTMASTER™

Rev. AB.01 Date: March 14, 2007 Manual # 0-2956

Operating Features:

A-04517

Operating Manual

WE APPRECIATEYOUR BUSINESS!

Congratulations on your new Thermal Dynamics product. We are

proud to have you as our customer and will strive to provide you

with the best service and reliability in the industry. This product is

backed by our extensive warranty and world-wide service network.

To locate your nearest distributor or service agency call 1-800-

426-1888, or visit us on the web at www.thermal-dynamics.com.

This Operating Manual has been designed to instruct you on the

correct use and operation of your Thermal Dynamics product.

Your satisfaction with this product and its safe operation is our

ultimate concern. Therefore please take the time to read the entire

manual, especially the Safety Precautions. They will help you to

avoid potential hazards that may exist when working with this

product.

YOU ARE IN GOOD COMPANY!

The Brand of Choice for Contractors and Fabricators Worldwide.

Thermal Dynamics is a Global Brand of manual and automation

Plasma Cutting Products for Thermadyne Industries Inc.

We distinguish ourselves from our competition through market-

leading, dependable products that have stood the test of time.

We pride ourselves on technical innovation, competitive prices,

excellent delivery, superior customer service and technical

support, together with excellence in sales and marketing expertise.

Above all, we are committed to developing technologically

advanced products to achieve a safer working environment within

the welding industry.

WARNINGS

Read and understand this entire Manual and your employer’s safety practices before installing, operat-

ing, or servicing the equipment.

While the information contained in this Manual represents the Manufacturer's best judgement, the

Manufacturer assumes no liability for its use.

Plasma Cutting Power Supply

CutMaster™ 81

Operating Manual Number 0-2956

Covered under U.S. Patents.

Published by:

Thermal Dynamics Corporation

82 Benning Street

West Lebanon, New Hampshire, USA 03784

(603) 298-5711

www.thermal-dynamics.com

Thermal Dynamics Corporation

Reproduction of this work, in whole or in part, without written permission of the pub-

lisher is prohibited.

The publisher does not assume and hereby disclaims any liability to any party for any

loss or damage caused by any error or omission in this Manual, whether such error

results from negligence, accident, or any other cause.

Printed in the United States of America

Publication Date: March 14, 2007

Record the following information for Warranty purposes:

Where Purchased:____________________________________

Purchase Date:_______________________________________

Power Supply Serial #:________________________________

Torch Serial #:________________________________________

TABLE OF CONTENTS

SECTION 1:

GENERAL INFORMATION ................................................................................................ 1-1

1.01 Notes, Cautions and Warnings ...................................................................... 1-1

1.02 Important Safety Precautions ....................................................................... 1-1

1.03 Publications .................................................................................................. 1-2

1.04 Declaration of Conformity ............................................................................. 1-4

1.05 Statement of Warranty .................................................................................. 1-5

SECTION 2:

INTRODUCTION ............................................................................................................... 2-1

2.01 Scope of Manual .......................................................................................... 2-1

2.02 Power Supply Specifications......................................................................... 2-1

2.03 Input Wiring Specifications ........................................................................... 2-2

2.04 Power Supply Features ................................................................................. 2-3

2.05 Power Supply Options and Accessories ....................................................... 2-4

SECTION 3: INSTALLATION ..................................................................................................... 3-1

3.01 Unpacking .................................................................................................... 3-1

3.02 Lifting Options .............................................................................................. 3-1

3.03 Primary Input Power Connections ................................................................. 3-2

3.04 Gas Connections .......................................................................................... 3-4

3.05 Torch Connections ........................................................................................ 3-8

SECTION 4: OPERATION ......................................................................................................... 4-1

4.01 Product Features .......................................................................................... 4-1

4.02 Preparations For Operating ........................................................................... 4-2

SECTION 5:

SERVICE .......................................................................................................................... 5-1

5.01 General Maintenance .................................................................................... 5-1

5.02 Common Faults ............................................................................................ 5-5

5.03 Basic Troubleshooting Guide ......................................................................... 5-6

5.04 Power Supply Basic Parts Replacement ...................................................... 5-11

SECTION 6:

PARTS LISTS ................................................................................................................... 6-1

6.01 Introduction ................................................................................................... 6-1

6.02 Ordering Information ..................................................................................... 6-1

6.03 Power Supply Replacement .......................................................................... 6-1

6.04 Replacement Parts ....................................................................................... 6-2

6.05 Options and Accessories .............................................................................. 6-2

6.06 Torch Parts ................................................................................................... 6-3

TABLE OF CONTENTS (continued)

PATENT INFORMATION ............................................................................................................ 6-4

APPENDIX 1: SEQUENCE OF OPERATION

(BLOCK DIAGRAM) .......................................................................................................... A-1

APPENDIX 2: DATA TAG INFORMATION ................................................................................ A-2

APPENDIX 3: MAINTENANCE SCHEDULE ............................................................................. A-3

APPENDIX 4: TORCH PIN - OUT DIAGRAMS .......................................................................... A-4

APPENDIX 5: TORCH CONNECTION DIAGRAMS ................................................................... A-5

APPENDIX 6: SYSTEM SCHEMATIC, 208/230 VOLT UNITS ................................................. A-6

APPENDIX 7: SYSTEM SCHEMATIC, 400 / 460- VOLT UNITS ............................................... A-8

APPENDIX 8: SYSTEM SCHEMATIC, 600 VOLT UNITS ....................................................... A-10

APPENDIX 9: Publication History ........................................................................................... A-12

Global Customer Service Contact Information ..................................................... Inside Rear Cover

Manual 0-2956 1-1 GENERAL INFORMATION

SECTION 1:

GENERAL INFORMATION

1.01 Notes, Cautions and Warnings

Throughout this manual, notes, cautions, and warnings

are used to highlight important information. These high-

lights are categorized as follows:

NOTE

An operation, procedure, or background informa-

tion which requires additional emphasis or is help-

ful in efficient operation of the system.

CAUTION

A procedure which, if not properly followed, may

cause damage to the equipment.

WARNING

A procedure which, if not properly followed, may

cause injury to the operator or others in the oper-

ating area.

1.02 Important Safety Precautions

WARNINGS

OPERATION AND MAINTENANCE OF

PLASMA ARC EQUIPMENT CAN BE DAN-

GEROUS AND HAZARDOUS TO YOUR

HEALTH.

Plasma arc cutting produces intense electric and

magnetic emissions that may interfere with the

proper function of cardiac pacemakers, hearing aids,

or other electronic health equipment. Persons who

work near plasma arc cutting applications should

consult their medical health professional and the

manufacturer of the health equipment to determine

whether a hazard exists.

To prevent possible injury, read, understand and

follow all warnings, safety precautions and instruc-

tions before using the equipment. Call 1-603-298-

5711 or your local distributor if you have any ques-

tions.

GASES AND FUMES

Gases and fumes produced during the plasma cutting

process can be dangerous and hazardous to your health.

• Keep all fumes and gases from the breathing area.

Keep your head out of the welding fume plume.

• Use an air-supplied respirator if ventilation is not

adequate to remove all fumes and gases.

• The kinds of fumes and gases from the plasma arc

depend on the kind of metal being used, coatings

on the metal, and the different processes. You must

be very careful when cutting or welding any met-

als which may contain one or more of the follow-

ing:

Antimony Chromium Mercury

Arsenic Cobalt Nickel

Barium Copper Selenium

Beryllium Lead Silver

Cadmium Manganese Vanadium

• Always read the Material Safety Data Sheets

(MSDS) that should be supplied with the material

you are using. These MSDSs will give you the in-

formation regarding the kind and amount of fumes

and gases that may be dangerous to your health.

• For information on how to test for fumes and gases

in your workplace, refer to item 1 in Subsection 1.03,

Publications in this manual.

• Use special equipment, such as water or down draft

cutting tables, to capture fumes and gases.

• Do not use the plasma torch in an area where com-

bustible or explosive gases or materials are located.

• Phosgene, a toxic gas, is generated from the vapors

of chlorinated solvents and cleansers. Remove all

sources of these vapors.

• This product, when used for welding or cutting, pro-

duces fumes or gases which contain chemicals

known to the State of California to cause birth de-

fects and, in some cases, cancer. (California Health

& Safety Code Sec. 25249.5 et seq.)

ELECTRIC SHOCK

Electric Shock can injure or kill. The plasma arc process

uses and produces high voltage electrical energy. This

electric energy can cause severe or fatal shock to the op-

erator or others in the workplace.

• Never touch any parts that are electrically “live” or

“hot.”

GENERAL INFORMATION 1-2 Manual 0-2956

• Wear dry gloves and clothing. Insulate yourself

from the work piece or other parts of the welding

circuit.

• Repair or replace all worn or damaged parts.

• Extra care must be taken when the workplace is

moist or damp.

• Install and maintain equipment according to NEC

code, refer to item 9 in Subsection 1.03, Publications.

• Disconnect power source before performing any ser-

vice or repairs.

• Read and follow all the instructions in the Operat-

ing Manual.

FIRE AND EXPLOSION

Fire and explosion can be caused by hot slag, sparks, or

the plasma arc.

• Be sure there is no combustible or flammable mate-

rial in the workplace. Any material that cannot be

removed must be protected.

• Ventilate all flammable or explosive vapors from

the workplace.

• Do not cut or weld on containers that may have held

combustibles.

• Provide a fire watch when working in an area where

fire hazards may exist.

• Hydrogen gas may be formed and trapped under

aluminum workpieces when they are cut underwa-

ter or while using a water table. DO NOT cut alu-

minum alloys underwater or on a water table un-

less the hydrogen gas can be eliminated or

dissipated. Trapped hydrogen gas that is ignited

will cause an explosion.

NOISE

Noise can cause permanent hearing loss. Plasma arc pro-

cesses can cause noise levels to exceed safe limits. You

must protect your ears from loud noise to prevent per-

manent loss of hearing.

• To protect your hearing from loud noise, wear pro-

tective ear plugs and/or ear muffs. Protect others

in the workplace.

• Noise levels should be measured to be sure the deci-

bels (sound) do not exceed safe levels.

• For information on how to test for noise, see item 1

in Subsection 1.03, Publications, in this manual.

PLASMA ARC RAYS

Plasma Arc Rays can injure your eyes and burn your skin.

The plasma arc process produces very bright ultra violet

and infra red light. These arc rays will damage your eyes

and burn your skin if you are not properly protected.

• To protect your eyes, always wear a welding hel-

met or shield. Also always wear safety glasses with

side shields, goggles or other protective eye wear.

• Wear welding gloves and suitable clothing to pro-

tect your skin from the arc rays and sparks.

• Keep helmet and safety glasses in good condition.

Replace lenses when cracked, chipped or dirty.

• Protect others in the work area from the arc rays.

Use protective booths, screens or shields.

• Use the shade of lens as suggested in the following

per ANSI/ASC Z49.1:

Minimum Protective Suggested

Arc Current Shade No. Shade No.

Less Than 300* 8 9

300 - 400* 9 12

400 - 800* 10 14

* These values apply where the actual arc is clearly

seen. Experience has shown that lighter filters may

be used when the arc is hidden by the workpiece.

1.03 Publications

Refer to the following standards or their latest revisions

for more information:

1. OSHA, SAFETY AND HEALTH STANDARDS, 29CFR

1910, obtainable from the Superintendent of Documents,

U.S. Government Printing Office, Washington, D.C.

20402

2. ANSI Standard Z49.1, SAFETY IN WELDING AND

CUTTING, obtainable from the American Welding So-

ciety, 550 N.W. LeJeune Rd, Miami, FL 33126

3. NIOSH, SAFETY AND HEALTH IN ARC WELDING

AND GAS WELDING AND CUTTING, obtainable from

the Superintendent of Documents, U.S. Government

Printing Office, Washington, D.C. 20402

4. ANSI Standard Z87.1, SAFE PRACTICES FOR OCCU-

PATION AND EDUCATIONAL EYE AND FACE PRO-

TECTION, obtainable from American National Stan-

dards Institute, 1430 Broadway, New York, NY 10018

5. ANSI Standard Z41.1, STANDARD FOR MEN’S

SAFETY-TOE FOOTWEAR, obtainable from the Ameri-

can National Standards Institute, 1430 Broadway, New

York, NY 10018

Manual 0-2956 1-3 GENERAL INFORMATION

6. ANSI Standard Z49.2, FIRE PREVENTION IN THE USE

OF CUTTING AND WELDING PROCESSES, obtain-

able from American National Standards Institute, 1430

Broadway, New York, NY 10018

7. AWS Standard A6.0, WELDING AND CUTTING

CONTAINERS WHICH HAVE HELD COMBUS-

TIBLES, obtainable from American Welding Society,

550 N.W. LeJeune Rd, Miami, FL 33126

8. NFPA Standard 51, OXYGEN-FUEL GAS SYSTEMS

FOR WELDING, CUTTING AND ALLIED PRO-

CESSES, obtainable from the National Fire Protection

Association, Batterymarch Park, Quincy, MA 02269

9. NFPA Standard 70, NATIONAL ELECTRICAL CODE,

obtainable from the National Fire Protection Associa-

tion, Batterymarch Park, Quincy, MA 02269

10. NFPA Standard 51B, CUTTING AND WELDING PRO-

CESSES, obtainable from the National Fire Protection

Association, Batterymarch Park, Quincy, MA 02269

11. CGA Pamphlet P-1, SAFE HANDLING OF COM-

PRESSED GASES IN CYLINDERS, obtainable from the

Compressed Gas Association, 1235 Jefferson Davis

Highway, Suite 501, Arlington, VA 22202

12. CSA Standard W117.2, CODE FOR SAFETY IN WELD-

ING AND CUTTING, obtainable from the Canadian

Standards Association, Standards Sales, 178 Rexdale

Boulevard, Rexdale, Ontario, Canada M9W 1R3

13. NWSA booklet, WELDING SAFETY BIBLIOGRAPHY

obtainable from the National Welding Supply Associa-

tion, 1900 Arch Street, Philadelphia, PA 19103

14. American Welding Society Standard AWSF4.1, RECOM-

MENDED SAFE PRACTICES FOR THE PREPARA-

TION FOR WELDING AND CUTTING OF CONTAIN-

ERS AND PIPING THAT HAVE HELD HAZARDOUS

SUBSTANCES, obtainable from the American Welding

Society, 550 N.W. LeJeune Rd, Miami, FL 33126

15. ANSI Standard Z88.2, PRACTICE FOR RESPIRATORY

PROTECTION, obtainable from American National

Standards Institute, 1430 Broadway, New York, NY

10018

GENERAL INFORMATION 1-4 Manual 0-2956

1.04 Declaration of Conformity

Manufacturer: Thermal Dynamics Corporation

Address: 82 Benning Street

West Lebanon, New Hampshire 03784

USA

The equipment described in this manual conforms to all applicable aspects and regulations of the ‘Low Voltage Directive’

(European Council Directive 73/23/EEC as amended by Council Directive 93/68/EEC) and to the National legislation for

the enforcement of this Directive.

Serial numbers are unique with each individual piece of equipment and details description, parts used to manufacture a unit

and date of manufacture.

National Standard and Technical Specifications

The product is designed and manufactured to a number of standards and technical requirements. Among them are:

* CSA (Canadian Standards Association) standard C22.2 number 60 for Arc welding equipment.

* UL (Underwriters Laboratory) rating 94VO flammability testing for all printed-circuit boards used.

* ISO/IEC 60974-1 (BS 638-PT10) (EN 60 974-1) (EN50192) (EN50078) applicable to plasma cutting equipment and associ-

ated accessories.

* Extensive product design verification is conducted at the manufacturing facility as part of the routine design and manufac-

turing process. This is to ensure the product is safe, when used according to instructions in this manual and related

industry standards, and performs as specified. Rigorous testing is incorporated into the manufacturing process to ensure

the manufactured product meets or exceeds all design specifications.

Thermal Dynamics has been manufacturing products for more than 30 years, and will continue to achieve excellence in our

area of manufacture.

Manufacturers responsible representative: Giorgio Bassi

Managing Director

Thermal Dynamics Europe

Via rio Fabbiani 8A

40067 Rastignano (BO)

Italy

Andere Handbücher für CUTMASTER 81

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Thermal Dynamics Schweißsystem Handbücher

Thermal Dynamics

Thermal Dynamics AUTO-CUT 30 O2 Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics cutmaster A60 Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics CE CutMaster 80XL Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics Pak Master 100XL Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics 200 ULTRA-CUT Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics CUTMASTER Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics SIGNATURE PAK 1250XRTM Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics CUTMASTER 39 Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics CUTMASTER 12 Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics SureLok PCM-102 Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics CutSkill PCH-42 Torch Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics C-20A Cutskill Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics CutMaster 58 Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics 38 Cutmaster Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics 1-4730-6 Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics PakMaster 75XL Plus Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics Drag-gun Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics VICTOR 200 AUTO-CUT Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics MERLIN 6000 Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics MERLIN 6000 Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics Econo-Pak 50 Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics DRAG-GUN 38 Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics PAK 200 Bedienungsanleitung

Thermal Dynamics

Thermal Dynamics CutMaster 40MM Bedienungsanleitung

Beliebte Schweißsystem Handbücher anderer Marken

Berner

Berner PLASMACUT 54 Bedienungsanleitung

Pro Spot

Pro Spot PR-155 Bedienungsanleitung

Forney

Forney 210 Bedienungsanleitung

Thermal Arc

Thermal Arc 400S Bedienungsanleitung

Lincoln Electric

Lincoln Electric HANDYMIG 170I Bedienungsanleitung

GYS

GYS PROTIG 201 AC/DC Bedienungsanleitung

TAFA

TAFA 30*8B35 Bedienungsanleitung

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung

ESAB

ESAB Buddy Arc 145 Bedienungsanleitung

CIGWELD

CIGWELD 636804 Kurzanleitung

Red-D-Arc

Red-D-Arc DC-400 Bedienungsanleitung

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung

Elettro

Elettro HI-MIG 3000 SYNERGIC Bedienungsanleitung

WIA

WIA Weldmatic 270 CP132-2 Bedienungsanleitung

Sonics

Sonics H520T Bedienungsanleitung

Miller

Miller Big Blue 400D Bedienungsanleitung

NewArc

NewArc RT2000 Kurzanleitung

Hypertherm

Hypertherm powermax1000 Bedienungsanleitung