Thermaltake FANLESS VGA Bedienungsanleitung

Note Component

Fanless VGAFanless VGA

>> 01>> 20

Main front

heat sink X1

Main rear

heat sink X1

( Unit : mm )

Nut-C X 3

Thermal

Grease

Thermal grease X 1

Heatpipe X 2

Package A Package B

Screw-A X 3

Screw-B X 3

Front heat

sink base X1

Rear heat

sink base X1

Screw-D X 6 ( for rear heat sink base )

Clip sets X 2

Screw-E X 10 ( for main front and rear heat sink )

Spare parts are included.

Package C

Washer X 4

Screws :

Fanless VGA

Exploded Drawing

>> 02

Front heat

sink base

Screw-B

Main rear heat sink

Adhesive tape

Rear heat sink base

Nut - C

Main front

heat sink

Clip set

Screw-A

Screw - D

Screw - E

Heatpipe

Check Point

Fanless VGA

>> 19

1. After completing the Fanless VGA installation, turn on the

computer to check if both of the main heat sink are at

similar temperature range (Leave the computer running

for a few minutes to confirm the temperature and you can

tell the difference by turning the computer off and touch

both of the heatsinks with your hand).

If temperature for both main heat sink seems to differ

greatly, please check the following:

A. Is the thermal grease properly spread onto the following

six areas:

a. On the surface of front heat sink base

b. Inside the tunnel of front heat sink base

c. On the surface of rear heat sink base

d. Inside the tunnel of rear heat sink base

e. Inside the tunnel of main front heat sink

f. Inside the tunnel of main rear heat sink

B. Is the GPU and the front heat sink base tightly in contact?

C. Is the heatpipe properly in contact with the heat sinks?

2. We do not recommend overclocking the video card. We

are not responsible for any damages caused by

overclocking.

3. If the heatpipe is tampered with or scratched by a sharp

object, it may not function properly. Please handle with

care.

4. After successfully installing the video card, do not shake

or exert excessive force on any part of the heat sinks.

The screws and nuts that hold the heat sinks may

become loose.

FANLESS VGA

User's Manual

www.thermaltake.com

Address: Unit 1, 49 Henderson Road Rowville

Victoria 3178 Australia

TEL: +61- (03) 9763 1622 FAX: +61- (03) 9763 1677

E-mail: [email protected]

URL: www.thermaltake.com.au

Australia: Thermaltake Australia and

New Zealand Pty Ltd

Address: 73, Bld de Courcerin Parc du Courcerin 77185 Lognes

TEL: + 33 - (0)160 1763 15 FAX: + 33 - (0)1 60 17 63 16

E-mail : [email protected]

France: Thermaltake France

Address: #907,HaiTai Plaza, No.229, North 4th

Ring Road, Haidian District,Beijing 100083 PRChina

TEL:+86-10-82883159/3189 FAX:+86-10-82376577

E-mail: [email protected]

China: Thermaltake Beijing Co.Ltd

Overseas Branch

Address: 525Parritott Place,

City of Industry, CA 91746

TEL: (626)968-9189 FAX: (626)968-7659

E-mail: [email protected]

USA: Thermaltake Technology Inc.

Address: 8F, No.27, Lane 155, Sec.3, Pei Shen Road, Saen

Keng Hsiang, Taipei Hsiang, Taiwan

TEL:(886) 2-2662-6501 FAX:(886) 2-2662-6510

E-mail: [email protected]

Taiwan : Thermaltake Technology Co.,Ltd.

Address: No.5-A, Hei-An Bldg 2-6-16 Okubo,

Shinjuku-ku, Tokyo, 169-0072, Japan

TEL: +81- 3-3203-3371 FAX: +81- 3-3203-3372

E-mail: [email protected]

Japan: Thermaltake Japan Inc.

O1693

Note Dual heatpipe VGA cooler

Fanless VGAFanless VGA

>>>> 22

Thank you for purchasing Fanless VGA. This product is a

new GPU thermal solution that applies heatpipe

technology and can be applied to video card with

mounting holes on the PCB.

Be sure to read this user guide in order to use this

product properly and safely.

Features :

>> - High performance fanless GPU cooler,

0dBA cooling solution, reduce total

system noise

- Dual heatpipe move the heat more

efficiently

- Much better heat dissipation is

delivered by larger heatsink surface

- Universal clip for both nVIDIA and Ati

Note

Contents

>> 21

Heat Sink Base Installation

Clip Installation

Heatpipe Installation

Component

NOTICE: Thermaltake is not responsible for

any damaged caused by the incorrect

installation or usage of this product.

Fanless VGAFanless VGA

Installation Installation

>> 03>> 18

Heat sink base

Installation

Main rear heat sink plate

Step12: Position the main rear heat sink.

After applying equal amount of thermal grease on the

tunnel of the main rear heat sink, position the main rear

heat sink plate toward the heatpipe and then mount it onto

the rear heat sink base using screw-E.

Important : Make sure the finished

Fanless VGA is similar to the picture

as shown. Main rear heat sink needs

to be in position underneath with the

main front heat sink.

Screw - E

Fanless VGAFanless VGA

Installation Installation

>> 17>> 04

Make sure the surface of the GPU core are clean before

applying thermal grease onto it.

Step1: Apply the thermal grease on the GPU.

Front Back

Fanless VGAFanless VGA

Thermal

Grease

>> Important : Make sure the

position of the heatpipe is

according to the drawing.

Step11: Apply the thermal grease on the

rear heat sink base.

Turn the card over and apply equal amount of thermal

grease on the rear heat sink base (Thermal grease

should also be applied into the tunnel ). Then, position

the heatpipe into the tunnel on rear heat sink base.

Front

Back

Installation Installation

>> 05>> 16

Step10: Mount the main front heat sink.

Mount the main front heat sink onto it using screw-E.

Front View

Attention on the

position of the

inserted heatpipe

Side View

Screw - E

Important :

Most GPU`s on the video card are slightly concave, the

curvature of which is directed toward the center. Thus,

more thermal grease is required at the center. Also, in the

case of the ATI Radeon 9700 Pro and 9800 Pro, the

protruding graphics core is surrounded by a protective

frame, which is higher than the core itself, thus generous

amounts of thermal grease must be applied on the core.

If proper contact between the front heatsink and the GPU

core cannot be made, it will lead to the possibility of the

core being overheat.

ATI Radeon 9700 Pro

ATI Radeon 9800 Pro

Fanless VGAFanless VGA

Installation Installation

>> 15>> 06

Step2: Place the front heat sink base.

Place the front heat sink base on top of the GPU.

Front heat sink base

Front

Heatpipe

Position the heatpipe into the tunnel on front heat sink

base.

Step9: Install the heatpipe.

The pointed part of the heatpipe

should be facing downward.

Important :

Please pay attention to the

position of the inserted heatpipe.

Fanless VGAFanless VGA

>> >>

Andere Thermaltake Computerhardware Handbücher

Thermaltake

Thermaltake Pacific W6 AMD T4 Bedienungsanleitung

Thermaltake

Thermaltake Floe RC240 Bedienungsanleitung

Thermaltake

Thermaltake Pacific V-RTX 4080 Plus Bedienungsanleitung

Thermaltake

Thermaltake Pacific R240 D5 Bedienungsanleitung

Thermaltake

Thermaltake Water 3.0 Riing RGB 360 Bedienungsanleitung

Thermaltake

Thermaltake Pacific MX2 Ultra Bedienungsanleitung

Thermaltake

Thermaltake TH360 ARGB Sync Bedienungsanleitung

Thermaltake

Thermaltake Divider 370 TG ARGB Bedienungsanleitung

Thermaltake

Thermaltake C240 Bedienungsanleitung

Thermaltake

Thermaltake A2016 Bedienungsanleitung

Thermaltake

Thermaltake Floe Ultra 240 RGB Bedienungsanleitung

Thermaltake

Thermaltake A1827 Bedienungsanleitung

Thermaltake

Thermaltake Riing Silent 12 Sync Bedienungsanleitung

Thermaltake

Thermaltake M360 Plus Bedienungsanleitung

Thermaltake

Thermaltake Pacific PR12-D5 Plus Bedienungsanleitung

Thermaltake

Thermaltake TOUGHLIQUID 360 ARGB TRX40 Edition Bedienungsanleitung

Thermaltake

Thermaltake Pacific V-RTX 3070 Plus Bedienungsanleitung

Thermaltake

Thermaltake Extreme Spirit Il Bedienungsanleitung

Thermaltake

Thermaltake Pacific V-RTX 2070 Super Plus Bedienungsanleitung

Thermaltake

Thermaltake M900 XXL RGB Bedienungsanleitung

Thermaltake

Thermaltake Pacific RL360 D5 Bedienungsanleitung

Thermaltake

Thermaltake TOUGHLIQUID Ultra 360 Bedienungsanleitung

Thermaltake

Thermaltake Pacific W5 Bedienungsanleitung

Thermaltake

Thermaltake Pacific RL360 Bedienungsanleitung

Beliebte Computerhardware Handbücher anderer Marken

EMC2

EMC2 VNX Series Betriebsanleitung

Panasonic

Panasonic DV0PM20105 Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung

Gigabyte

Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung

Raidon

Raidon iT2300 Bedienungsanleitung

National Instruments

National Instruments PXI-8186 Bedienungsanleitung

Hauppauge

Hauppauge WinTV-HVR-2250 Bedienungsanleitung

Kontron

Kontron CP6002 Bedienungsanleitung

Manhattan

Manhattan 702843 Bedienungsanleitung

Aphex

Aphex 230 Bedienungsanleitung

Intel

Intel NUC 12 Pro Bedienungsanleitung

Galaxy

Galaxy GHDX2-2430S-24F4D Bedienungsanleitung

Intel

Intel AXXRMFBU4 Bedienungsanleitung

Kontron

Kontron DIMM-PC/MD Bedienungsanleitung

ST X-NUCLEO-SAFEA1B Betriebsanleitung

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Bedienungsanleitung

Advantech

Advantech ASMB-935 Series Bedienungsanleitung

Jupiter

Jupiter RAM PACK Bedienungsanleitung