Thermaltake ATX 12V 2.2 Bedienungsanleitung

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

~ Embedded Socket and

Modularized Cable Management ~

ATX 12V 2.2 & EPS 12V 2.91

Fan

14cm

www.thermaltake.com [email protected]

E161451

Toughpower

CableManagement 1200W

297X 210 mm

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

Table of contents

1.Introduction 01

2.Product Features

3.Components Check

4.Connectors & Modularized Cable

Management

5.Installation

6.+12V Rail Distribution and PCI-E

Connectors

7.SPEC Table

8.Other Specification

9.Trouble Shooting

10.Contact Us

1. Introduction

We live up to the promise of Thermaltake logo in our unending

quest for excellence. Shall you have any suggestion or

comments, please access our website:

Http://www.thermaltake.com

or e-mail to:

[email protected]

We appreciate your kindly feedback and you will receive the

prompt response from our customer service team.

Please take the time in familiarizing yourself with the power

supply, its connectors and the contents of this manual before

proceeding with the installation of the power unit. You will need

a Philips crosshead screwdriver, perhaps your PC case manual

and most certainly your motherboard manual.

Should you have any questions regarding the content of the

manual, please contact Thermaltake directly. Failure to follow

the proper procedures may cause severe bodily harm or PC

component damage.

1.1 Statement

297X 210 mm

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

1.2 Warnings and Cautions

2. Product Features

1.2.1 Do not pull the AC power cord when the power supply is

in use or the damages to the components will occur.

1.2.2 Do not store the Power Supply in high humidity and high

temperature environment.

1.2.3 When usin

power supply under testing conditions where the power

supply unit is not installed in a PC with its components,

please follow the steps below:

1) Please take a paper clip and untwist it.

2) Make sure the power supply unit is in the "OFF"

position.

3) Locate the 20+4 pin motherboard connector from the

power supply unit.

4) Plug one side of the paper clip into the green wire hole.

5) Plug the other side of the paper clip into any of the

black wire holes.

6) Turn on the PSU to see if the power supply fan(s)

turn(s) on.

1.2.4 High voltages exist in the power supply. Do not open the

power supply case unless you are an authorized service

technician or electrician.

1.2.5 All warrantees and guarantees shall be voided should

there be a failure to comply with any of the warnings and

cautions covered in this manual.

g Toughpower Cable Management 1200W

2.1 NEW 8 pin PCI-E Connector

Toughpower 1200W power supplies come with three of the

latest 8-pin PCI-E connectors required for the next

generation NVIDIAand ATI graphics cards. These new

defined 8-pin connectors are downward compatible with

the existing 6-pin PCI-E connectors with an 8 pin to 6 pin

converter. Thus, with the included three 6-pin/8-pin

connectors, Toughpower 1200W support up to three high-

end graphic cards.

2.2 Excellent Efficiency (up to 87%)

Toughpower 1200W provide excellent efficiency and hence

reducing energy consumption. That in return reduces

customers electricity bill.

2.3 140mm Ball-Bearing Fan

The 140mm ball bearing fan effectively increases the

airflow inside the PSU and decreases the ambient

temperature.

2.4 Extremely good voltage regulation ( 3%)

This feature allows tighter load regulation ( 3%) than other

power supplies ( 5%) and increase system voltage

stability.

2.5 MTBF > 120,000 hours (Highly reliable)

120,000 hours of MTBF (Mean Time between Failures)

goes above and beyond all ATX specifications.

02 03

297X 210 mm

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

4 mounting screws

One AC Input power cord 7

2Three sets ofwire w/ 8pin

PCI-E connector

3Three sets ofwire w/

6pin PCI-E connector

4Two setsof wires w/5pin

SATA connector

5Two setsof wire w/4pin

peripheral connector

User manual

One Toughpower1200W

power supply unit(w/one

20+4pin main power

connector, one4+4pin

+12V power connector, and

one 8pin powerconnector)

3. Components Check

2.6 Four Independent +12V rails

Four independent +12V rails are provided to support the

high-end graphic card and PC system.

2.7 Cable Management

Cable Management enables users to remove unused

cables and significantly improves the airflow in the chassis.

2.8 Industrial grade components (capacitor,

transformer, etc)

All components are specially designed for industrial

environment and extreme conditions.

2.9 Hi-Tech Black Coating

With special Hi-Tech Black coating, Toughpower 1200W

PSUs looks professional, elegant and unique.

2.10 High +5VSB Output

Built-in higher +5VSB (from 2A to 3.5A(PS-ON status))

supports up to 12 USB devices. Also, even the system is

power off, USB devices can still be charged by the 3A

sustained output.

04 05

297X 210 mm

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

4. Connectors & Modularized

Cable Management

4.1 Connectors

4.1.1Main Power Connector (20+4 pin)

Support the latest ATX 12V 2.2 system motherboard

Voltage

+3.3V

COM

+5V

COM

+5V

COM

PWR_ON

+5Vsb

+12VDC

+3.3 V

Voltage

+3.3 V

-12 V

COM

PS_ON#

COM

N/C

+5 V

COM

Color

Orange

Black

Red

Black

Red

Black

Purple

Yellow

Orange

Color

Orange

Blue

Black

Green

Black

N/C

Red

Black

Gray

4.1.2 CPU Connector (4+4 pin)

Support both dual CPU and single CPU systems by

simply combining (8 pin) or splitting (4 pin X 2) the

connectors

4.1.3 CPU Connector (8 pin)

Support the latest 8 pin Quad Core system motherboard

Color Signal Pin

Black

Yellow

COM

Black COM

+12 DCV

Yellow

+12 DCV

Yellow

Color Signal Pin

Black

Yellow

GND

Black GND

+12 DCV

Yellow

+12 DCV

06 07

297X 210 mm

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

4.1.4 PCI-E Connector (8 pin)*

Support next generation 8 pin sockets on high-end

graphic cards and can support the existing 6 pin sockets

by connecting to the 8 pin to 6 pin converter.

Color Signal Pin

Yellow

Black

+12VDC

Black GND

GND

Black

GND

Black

4.1.5 PCI-E Connector (6 pin)*

Support the latest high-end graphic cards with 6 pin

socket

Color Signal Pin

Yellow 12VDC 1

Yellow 12VDC 2

Yellow 12VDC 3

Black COM 4

Black COM 5

Black COM 6

4.1.6 SATAConnector (5 pin)

Support the new generation high-speed SATAdevices

Yellow +12VDC 1

Black COM 2

Red +5VDC 3

Black COM 4

Orange +3.3 VDC 5

Color Signal Pin

4.1.7 Peripheral Connector (4 pin)

Support IDE/SCSI (HDD/CD/DVD..etc) devices

Color Signal Pin

Yellow

Black

Red

+12VDC

COM

+5VDC

*A 6pin & a8 pin PCI-Econnectors can beconnected to thesame graphic cardif there are

two 6 pinsockets or both8 pin socketand 6 pinsockets available onthe card. Pleaserefer to

Section 6.2 formore information.

08 09

297X 210 mm

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

4.1.8 Floppy Disk Connector (4 pin)

Support Floppy Disk and some other additional devices

Color Signal Pin

Red

Black

Black COM

COM

+12VDC

Yellow

+5VDC

4.2 Modularized Cable Management:

Users can optimize the cables arrangement within the chassis

by using only what users need. This feather increases the

airflow and reduces the overall ambient temperature within the

chassis, also improves the overall look and tidiness of the

system.

Embedded Socket and Modularized Cable

Management Design:

PCI-Express

Connector

SATA, Peripheral, and

Floppy Connector

10 11

297X 210 mm

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

5. Installation Steps

To prevent electrical shocks, please disconnect the power cord

from your existing power supply unit. Toughpower 1200W

Power Supply has automatic voltage selector which will

automatically change to 100V-240V PSU.

StepStepStep 1

After install the power supply unit into the chassis and then

connect the 20+4-pin main power cable to motherboard 20pin

or 24 pin socket.

StepStepStep 2

Connect the 4+4-pin/8-pin +12V auxiliary power connector to

the motherboard. (Users can use either 4 pins or 8 pins,

depending on the motherboard. Please check with the

motherboard user's manual.)

StepStepStep 3

Connect the 6 pin/8 ping PCI-Express connector to your

graphic card if needed. (Notice: Before the connection,

please refer to Section 6.2 for more information.)

StepStepStep 4

Connect the 4 pin power connector to peripheral devices such

as DVD-Burner, hard drive, and etc. In addition, a user can

connect the 3-pin floppy power connector to connect the floppy

drive.

12 13

297X 210 mm

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

If there are S-ATA hard disk drives present, there are also

Serial ATA connectors available.

6. +12V Rail Distribution &

PCI-E Connectors

6.1. +12V Rail Distribution

W0133 1200W

24 pin +12V

4+4 pin +12V

8 pin +12V

Peripheral & Floppy

S-ATA

6 pin Modular PCI-E

8 pin Modular PCI-E

12V1

12V2

12V2, 12V3

12V1

12V3

12V4

12V3

12V4

6.2. PCI-E Connectors and +12V Rails

Distribution

Please carefully read the table and suggestions below when

connecting the 6 pin/8 pin connectors to your graphic card(s),

especially when there are more than one PCI-E sockets

available on your card(s).

14 15

297X 210 mm

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

Toughpower

CableManagement 1200W ATX12V 2.2 & EPS 12V 2.91 Version

Please be noticed that when trying to connect more than one

connector to a graphic card, it is strongly recommended to

choose the connectors from exactly the same +12V rail.

6 pin 6 pin 6 pin 8 pin 8 pin 8 pin

12V3

12V4

XXX

7. SPEC Table

Model

W0133

SPECIFICATION

Power

Dimension

Switches

PFC

Cooling System

Noise

P. G. Signal

Efficiency

INPUT

Input Voltage

Input Frequency Range

MTBF

Input Current

Hold-up Time

1200W

200mm(L)x160mm(W)x86mm(H)

ATX Logic on-off additional power rockerswitch

Active PFC (PF> 0.9)

140mm Fan, 2300RPM 10%

16 dBAat 1300 RPM

100-500 ms

up to 87%

16ms

115 VAC ~ 230 VAC

47 ~ 63 H z

120,000 hrs minimum(at 25 )

15A

OUTPUT

Max/Min *1

Regulation *2

Ripple & Noise Output

+12V1

+12V4

+12V2

+12V3

+5V

+3.3V

-12V

+5Vsb

Total Power 1200W

20A/1A +3,-3% 120mV 600W

600W

250W

9.6W

17.5W

120mV

50mV

120mV

+3,-3%

+3,-5%

+10,-10%

36A/1A

20A/1A

36A/1A

30A/0.5A

0.8A/0A

3.5A/0A

*1. +5Vsb operate at 3.5A max load base on PS-ON mode. If PS-OFF +5Vsb only operate at 3A max load.

*2. Add 0.1uF and 10uF capacitors across output terminal during ripple & noise test.

ENVIRONMENT

Operating Temp.

Storage Temp.

Operating Humidity

Storage Humidity

10 to 50

-20 to 70

20% to 90%, non-condensing

5% to 95%, non-condensing

PROTECTION

DC rail Trigger Point/Range

Over Voltage Protection

Over Current Protection

Under Voltage Protection

Short Protection All output to GND

+3.3V trip point

+5.0V trip point

+12.0V trip point

+3.3V

+5.0V

+12V1 & +12V2

+12V3 & +12V4

+3.3V trip point

+5.0V trip point

+12.0V trip point 8.5 Vmin

3.3 Vmin

2.0 Vmin

39A ~55A

22A ~35A

33A ~50A

15.6 Vmax

4.5 Vmax

7.0 Vmax

Peak Power 1300W

16 17

297X 210 mm

Andere Handbücher für ATX 12V 2.2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Thermaltake Stromversorgung Handbücher

Thermaltake

Thermaltake TR2 Bedienungsanleitung

Thermaltake

Thermaltake TOUGHPOWER GF1 ARGB 850W Bedienungsanleitung

Thermaltake

Thermaltake W0128RU Bedienungsanleitung

Thermaltake

Thermaltake SMART 700W Bedienungsanleitung

Thermaltake

Thermaltake W0117 Bedienungsanleitung

Thermaltake

Thermaltake W0172 Toughpower 850 AP Bedienungsanleitung

Thermaltake

Thermaltake Purepower W0328 Bedienungsanleitung

Thermaltake

Thermaltake W0105 Bedienungsanleitung

Thermaltake

Thermaltake EVO Blue Bedienungsanleitung

Thermaltake

Thermaltake TR2-430W Bedienungsanleitung

Thermaltake

Thermaltake Toughpower Grand Bedienungsanleitung

Thermaltake

Thermaltake W0131RU Bedienungsanleitung

Thermaltake

Thermaltake Toughpower Grand Bedienungsanleitung

Thermaltake

Thermaltake TR2 RX 700w Bedienungsanleitung

Thermaltake

Thermaltake Toughpower XT TPX-575M Bedienungsanleitung

Thermaltake

Thermaltake W0158 Bedienungsanleitung

Thermaltake

Thermaltake W0155RU Bedienungsanleitung

Thermaltake

Thermaltake W0151 Bedienungsanleitung

Thermaltake

Thermaltake W0156 Bedienungsanleitung

Thermaltake

Thermaltake Toughpower XT Bedienungsanleitung

Thermaltake

Thermaltake W0103 Toughpower 600 AP Betriebsanleitung

Thermaltake

Thermaltake W0116RU Bedienungsanleitung

Thermaltake

Thermaltake TR2 500W Bedienungsanleitung

Thermaltake

Thermaltake Toughpower 800W Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung