Thrustmaster TH8 RS Bedienungsanleitung

ENGLISH: TH8 RS Tool v1.0.7.0 Calibration Software

FRANÇAIS : Logiciel de calibration “TH8 RS Tool v1.0.7.0”

DEUTSCH: TH8 RS Tool v1.0.7.0 Kalibrierungssoftware

NEDERLANDS: Kalibratiesoftware “TH8 RS Tool v1.0.7.0”

ITALIANO: Software di calibrazione “TH8 RS Tool v1.0.7.0”

ESPAÑOL: Software de calibración “TH8 RS Tool v1.0.7.0”

PORTUGUÊS:Software de calibragem “TH8 RS Tool v1.0.7.0”

РУССКИЙ: ПО для калибровки TH8 RS Tool v1.0.7.0

ΕΛΛΗΝΙΚΑ: Λογισμικό βαθμονόμησης "TH8 RS Tool v1.0.7.0"

TÜRKÇE: “TH8 RS Tool v1.0.7.0” Kalibrasyon Yazılımı

日本語 :較正ソフトウェア“TH8 RS Tool v1.0.7.0”

ENGLISH: TH8 RS Tool v1.0.7.0 Calibration Software

(Windows XP / Vista / 7)

This advanced calibration software enables you to adjust electronic gear stroke

settings, and recalibrate the shifter as required.

After following these instructions, click Close to exit the software, then disconnect

the shifter from the USB port before reconnecting it.

All your settings will then automatically be saved to your shifter's internal memory,

and will function both on PC and PlayStation® 3.

Note: You can skip any step by clicking the SKIP button. Both shift plates - i.e. H-pattern

(7+1) and Sequential (-/+) - can be calibrated independently.

Important note:

To avoid any conflicts, the TH8 RS Control Panel MUST be closed before the

calibration software is started.

To launch the application

Simply double-click the TH8 RS Calibration v1.0.7.0 icon

H-pattern (7+1) Shift Plate Setup

The following screen appears:

•CALIBRATE Step (to recalibrate your shifter with an H-pattern shift plate)

- Move the stick in all 8 directions (1-2-3-4-5-6-7-R), several times if required, until the

white line fits within each of the 8 green rectangles.

The upper 4 green rectangles represent the signals received from speeds 1-3-5-7

The lower 4 green rectangles represent the signals received from speeds 2-4-6-R

- Replace the stick at the center and wait for the CALIBRATE OK tab to turn green. You

have completed the calibration process.

•TEST Step (to test your calibration)

- Move the lever twice in each direction

(i.e. 2x1–2x2 – 2x3 – 2x4 – 2x5 – 2x6 – 2x7 – 2xR), until the Test H8 - OK tab turns

green.

= You have completed the test process.

•FINE-TUNE Step

(to adjust electronic gear stroke settings for each of the 8 available gears)

- Use your mouse to move the green lines drawing the green rectangles at your

convenience.

This setting will enable you to determine at which point the signal for each speed is

triggered.

Example: In this case, the 2 green horizontal lines are very close to the cursor

= Short-stroke shifter

Example: In this case, the 2 green horizontal lines are very far from the cursor

= Long-stroke shifter

During this phase, make sure that you do not exceed the limits; the white lines must

always fall within the green rectangles. You can check this by shifting into gear; the

rectangle must always be highlighted in green when you shift into the relevant gear.

You can also move the vertical green lines.

Example: In this case, positions 5 and 7 both trigger the 5th gear (in games):

When you are satisfied with your adjustments, click Apply:

the Fine-Tune Saved tab then turns green.

- You can now exit the software by clicking Close.

Fine-Tuning the ANALOG mode

(This section is only applicable if using the ANALOG mode for PC!)

By default, the ANALOG mode features a limited "dead zone" at the beginning or the end

of the gear stroke.

You can reduce this dead zone by simply stretching the vertical lines drawing the 3rd

gear's green rectangle.

Example: Dead zone removed

Sequential (-/+) Shift Plate Setup

The following screen appears:

•CALIBRATE Step (to recalibrate your shifter with a Sequential shift plate)

The shift plate MUST be correctly attached during this operation; if it moves, the

calibrated values will be incorrect!

- Move the stick in both directions (- and +)

- Release the stick and wait for the CALIBRATE OK tab to turn green. You have

completed the calibration process.

•TEST Step (to test your calibration)

Move the stick twice in each direction (- and +) and wait for the Test +/- OK tab to

turn green. You have completed the test process.

•FINE-TUNE Step

(to adjust electronic gear stroke settings for each of the 2 available gears)

- Use your mouse to move the green lines drawing the green rectangles at your

convenience; you can move them closer to or further away from cursor (no further than

the ends of the white line, however).

Example: In this case, the 2 green vertical lines are very close to the cursor

= Short-stroke shifter

When you are satisfied with your adjustments, click Apply:

the Fine-Tune Saved tab then turns green.

- You can now exit the software by clicking Close.

Then, disconnect the shifter from the USB connector and connect it again.

YOU ARE NOW READY TO PLAY!

Inhaltsverzeichnis

Sprachen:

Andere Thrustmaster Videospiel-Controller Handbücher

Thrustmaster

Thrustmaster TX Servo Base Bedienungsanleitung

Thrustmaster

Thrustmaster Score-A Bedienungsanleitung

Thrustmaster

Thrustmaster HOTAS WARTHOG Gebrauchsanweisung

Thrustmaster

Thrustmaster T500RS Bedienungsanleitung

Thrustmaster

Thrustmaster TCA Sidestick X Airbus Edition Bedienungsanleitung

Thrustmaster

Thrustmaster Enzo Ferrari wireless Bedienungsanleitung

Thrustmaster

Thrustmaster Ferrari GT Bedienungsanleitung

Thrustmaster

Thrustmaster RUN'N'DRIVE 3-IN-1 RUMBLE FORCE Bedienungsanleitung

Thrustmaster

Thrustmaster T-LCM Pedals Bedienungsanleitung

Thrustmaster

Thrustmaster GT Cockpit 458 Bedienungsanleitung

Thrustmaster

Thrustmaster HOTAS WARTHOG Gebrauchsanweisung

Thrustmaster

Thrustmaster TS-PC Racer Ferrari 488 Challenge Edition Bedienungsanleitung

Thrustmaster

Thrustmaster 360 Modena Force GT Bedienungsanleitung

Thrustmaster

Thrustmaster ADVANCE WIRELESS DUAL TRIGGER Bedienungsanleitung

Thrustmaster

Thrustmaster Afterburner Bedienungsanleitung

Thrustmaster

Thrustmaster GPX Bedienungsanleitung

Thrustmaster

Thrustmaster RGT Force Feedback CLUTCH Bedienungsanleitung

Thrustmaster

Thrustmaster HOTAS WARTHOG Gebrauchsanweisung

Thrustmaster

Thrustmaster T248 Bedienungsanleitung

Thrustmaster

Thrustmaster T-Wireless Black Bedienungsanleitung

Thrustmaster

Thrustmaster universal challenge Bedienungsanleitung

Thrustmaster

Thrustmaster FERRARI 488 GT3 WHEEL ADD-ON Bedienungsanleitung

Thrustmaster

Thrustmaster FERRARI MOTORS Bedienungsanleitung

Thrustmaster

Thrustmaster Ferrari GTE Wheel Add-On Bedienungsanleitung

Beliebte Videospiel-Controller Handbücher anderer Marken

Wasp

Wasp SL-6610 Bedienungsanleitung

JKG

JKG JKG2022A Bedienungsanleitung

Marvo

Marvo MG08 Bedienungsanleitung

Belkin

Belkin F8GBPC001 Bedienungsanleitung

GameSir

GameSir Z2 Bedienungsanleitung

Laser

Laser PCO-AGAMEC-BK Bedienungsanleitung

Cortex

Cortex VEXnet Bedienungsanleitung

Gioteck

Gioteck HF-1 Bedienungsanleitung

Nacon

Nacon DAIJA ARCADE STICK Bedienungsanleitung

SHAKS

SHAKS S1+ Bedienungsanleitung

YCCTEAM

YCCTEAM Joy Con Bedienungsanleitung

Hyperkin

Hyperkin Smartboy Bedienungsanleitung

Nerf

Nerf DuraGrip Bedienungsanleitung

MoveMaster

MoveMaster MoveMaster Bedienungsanleitung

WinWing

WinWing Super Libra J1 Bedienungsanleitung

ECCI

ECCI Trackstar 6000 Series Bedienungsanleitung

Logitech

Logitech 963291-0403 - Attack 3 Joystick Bedienungsanleitung

Pelican

Pelican Afterglow PL-678 Bedienungsanleitung