TIE SHIFT RED Bedienungsanleitung

SHIFT RED Quick Guide

PRECAUTIONS

Age Recommendation

•The SHIFT drone is not recommended for children below 14 years of age. Children below 14

years of age must be accompanied and supervised by an adult guardian when ying the drone.

Compliance with Relevant Laws

•When ying unmanned aerial vehicles (UAVs), you must observe the rules and regulations of the

authorities having jurisdiction over the relevant airspace.

•The operation of drones is prohibited near airports and areas where manned aerial vehicles

are ying at low altitudes. Borders and other areas where the operation of drones may result in

security issues are classied as restricted. Please observe all guidelines concerning altitude limit,

ight prohibition, and restricted zones.

Pre-ight Inspection

•Make sure that the drone and controller batteries are fully charged. The charging status of the

drone and controller can be checked using the SHIFT Drone application.

•Inspect the propellers. All propellers should be rmly xed. Worn, cracked, bent or damaged

propellers must be replaced.

•Make sure that the intelligent vision (camera) on the front side of the drone, and the lenses and

sensors of the bottom sensor system are clean and free of stains.

•Pay special attention to the battery level of the drone and controller, and take the necessary

safety measures when the drone, controller, or mobile application gives a warning. Read the

“Emergency Measures” section.

•Check that the intended ight path is free of obstacles such as people, animals, trees, and

buildings (This product lacks functions such as return-to-home, and collision avoidance or speed

control based on obstacle detection).

•Do not y the drone in areas under the inuence of strong magnetic elds or magnets.

•The recommended ight conditions are mild weather conditions with a temperature between

0°C–40°C (32°F–104°F). Be wary of sudden changes in wind direction or weather. Do not use the

aircraft in adverse weather conditions such as rain, snow, fog, and wind.

Precautions During Flight

•Only use the genuine SHIFT RED propellers. Do not use together with propellers of other brands.

•Do not attempt to grab or touch propellers that are in operation. Doing so may result in serious

injury.

•Keep a safe distance away from the drone.

•The distance between the drone and user should be no more than 300 m (984 ft), and the drone

should be controlled within visible range.

•The drone may not work properly when ying over highly reective surfaces such as water- or

snow-covered areas, or when ying in dark.

•Exercise caution right after ight as the motor and aircraft are heated up from operation.

•Using the controller in the proximity (within 30 cm [1.0 ft]) of other rings, metallic objects or

magnetic materials, near electronic devices that employ wireless communication or run on

motors, inside a steel- framed building, or within the inuence of a utility pole or a wireless station

may affect the detection range of the controller and controllability of the drone.

•In particular, a high density of Wi-Fi APs may disturb communications between the drone and

application. Before using the application, check your Wi-Fi environment.

•When the drone is ying over a dark (below 300 lux) or extremely bright (over 100,000 lux) surface,

or toward a bright light source, its ight performance may be affected. Check the surrounding

brightness before operating the drone.

Precautions on Managing Drone and Controller Batteries

•Always use genuine SHIFT LiPo batteries.

•Inspect batteries before charging or use.

•If a battery has been shocked, or if you notice abnormal smell, heat, discoloration, deformation, or

signs of leakage from it, never charge or use the defective battery.

•Do not modify or disassemble the battery wiring.

•Do not touch battery terminals with a pointed tool such as tweezers or a needle. This may

damage the battery and potentially cause a re.

•The ideal temperature range for battery charging is 5°C–45 °C (41°F–113°F). Make sure that the

battery temperature does not exceed 60°C (140°F). An overheated battery may cause serious

damage or catch re. Do not charge a battery near a heating apparatus or ammable material,

inside a vehicle, and any other area exceeding 50°C (122°F).

•Do not expose the batteries to moisture or direct sunlight.

•Keep batteries out of reach of children.

•Inserting the drone battery in the wrong direction may damage both the battery and drone.

•Exercise caution when handling the battery immediately after ight as it is heated up from

operation.

Unauthorized Disassembly Prohibited

•Unauthorized disassembly, replacement of parts, and reassembly of the SHIFT drone and

controller are strictly prohibited, except for the removal, installation, or replacement of propellers,

protectors, or batteries. this is engineering Inc. shall not be included in any legal action or held

liable for direct or indirect damage resulting from the aforementioned unauthorized changes to

the drone or controller by the user. Where an unauthorized change has been made, the product

shall not be covered by the warranty policy. Repairs may be denied or performed for a fee.

Legal Responsibility for Footage

•Unauthorized recording or distribution of footage containing other persons falls under privacy

infringement, and violators must assume legal responsibility. Prior permission must be obtained

if using the SHIFT drone to take photos or videos of other persons, and saving or distributing

such content.

•Unauthorized recording or distribution of footage containing private property falls under

trespassing, and violators must assume legal responsibility. Always obtain permission in

advance.

HANDLING THE AIRCRAFT

Powering On / Off

1. Press and hold the power button for two seconds and the aircraft will power on/off.

Light On

Powering on

Light O

Powering off

Long-press the power button

Charging Drone

Connect the aircraft to a USB port using the provided USB cable to begin charging.

aA certied USB adapter rated at 5 V and 1.5 A is recommended for charging. Connecting to a PC may cause delayed

or unsuccessful charging.

HANDLING THE CONTROLLER

With every change in the place of ight, users are recommended to turn the controller off and on

again so that control sensitivity may be automatically recalibrated.

Powering On / Off

1. Before turning on, place the controller ring at least 30 cm (1.0 ft) away from the controller stick.

2. Press and hold the power button for at least two seconds to turn on the controller.

aIf automatic calibration is unsuccessful due to environmental factors, the controller gives a warning beep and powers

off automatically.

aIf the controller does not turn off properly, press the reset button on the bottom with a pin of appropriate thickness. Hold

the pin vertically not to damage to the controller.

Paring with Aircraft

When the aircraft and controller are ready for ight, they are automatically paired and the controller’s

LED indicator turns solid white.

aIf the LED indicator does not turn solid, the controller and aircraft have not been paired successfully. Turn off the aircraft

and controller, and turn on again.

Charging Controller

Connect the controller’s USB port to a USB charger using the provided USB cable to begin charging.

aA certied USB adapter rated at 5 V and 1.5 A is recommended for charging. Connecting to a PC may cause delayed

or unsuccessful charging.

CONTROLLING THE DRONE

Taking Off

1. Place the drone level, horizontal to the ground and headed in the direction you are headed, and pair

it with the controller.

2. Wear the control ring on your thumb, and wrap your hand gently around the control stick. For

details on wearing the control ring and using the control stick, read “Flight control.”

3. Touch the center of the control pad with the ring for over one second, and the drone will take off

while playing a takeoff melody. After takeoff, lift the ring off the pad.

4. When the drone succeeds in automatic takeoff, the front LED and power button LED on the drone

blink once, and the drone stands by while hovering at a height of 1 m (3.3 ft).

Landing

1. While the drone is hovering, touch the center of the pad with the ring for over one second to initiate

automatic landing. During landing, you cannot control the drone by moving the ring.

2. Once the drone comes to a complete stop, the controller vibrates and the motors stop

automatically.

Flight Control

1. As shown in the gure, wear the ring on your left or right thumb with the thicker part facing

downward. Wrap your other ngers around the control stick, and place your index nger on the jog

button.

2. While the drone is hovering, press and hold the jog button to switch to ight mode. Ring control is

enabled after the controller vibrates once.

1cm

aWhen switching to ight mode using the jog button, the center of the ring on your thumb should be within 1 cm (0.04 in)

around and above the center of the controller pad. If the ring is out of the range, the controller gives off a warning and

fails in switching to ight mode.

3. The drone ies proportionately to the

height and direction of the ring. Move

your ring-wearing thumb in the desired

direction of ight, and the drone will y

in the same direction.

aYour thumb with the ring should be at an

adequate height above the controller pad to

allow better control over the flight altitude.

aThe degree of acceleration or deceleration

can be set proportionately to the distance moved by the ring.

4. When turning the head of the aircraft to the desired direction, turn the jog button accordingly.

5. If you press the jog button during ight, the controller vibrates once and the drone switches to

hovering.

6. If the ring is out of the sensing range of the controller, the controller vibrates once and the drone

automatically switches to hovering. The controller vibrates only in free ight mode, vibration

intensity may vary with preference settings of the controller.

7. You can switch between free ight mode (default) and assist mode by holding the jog button

during ight for over one second until the controller vibrates.

Emergency Measures

■Manual emergency stop

•The drone motors stop immediately when you press the jog button

and power button on the controller at the same time.

aExercise caution as a manual stop in midight may cause damage to the aircraft

or personal injuries.

■Self-stopping of the drone

•In case of a sudden change in surroundings such as a temperature drop or battery shortage, you

will be notied of an emergency both from the aircraft front LED and power button blinking twice

repeatedly and from the controller vibrating and sounding.

•Then, you should perform a safe landing within 30 seconds. About one minute later, the drone

enters self-stopping mode in which the drone keeps hovering and uncontrollable before it lands

automatically in ve seconds.

■Self-stopping of the controller

•In case of a sudden change in surroundings such as a temperature drop or battery shortage, you

will be notied of an emergency from the controller vibrating and sounding.

aThen, you should perform a safe landing within 30 seconds before the controller is powered off and the aircraft lands

automatically.

aThe controller may be charged during use with a portable battery.

■Self-stopping due to weak signals

•In case of weak signals between the controller and drone due to interference, the controller gives

off a warning sound and vibrates (1 time/2 seconds). Then, you should immediately perform a

safe landing.

•When the signaling is completely lost, the controller vibrates (3 times/second) to declare an

emergency and the drone switches to hovering before landing in ve seconds.

USING THE MOBILE APPLICATION

You can use the “SHIFT Drone” application to preview a drone video in real time, and try various

ight modes for the drone to shoot from different perspectives.

Installation and Execution

1. Search “SHIFT Drone” in Google Play or App Store, and download the app to your smartphone.

2. Turn on the drone, connect to SHIFT-DRONE-XXXXXXXX from your smartphone’s Wi-Fi settings,

and run the application.

aThe initial password to connect to SHIFT-DRONE-XXXXXXXX is 1234567890. Please reset the password for security,

and remember it for future use.

3. See below for details on the interface of the application.

aThe screenshots of the application interface provided in this User Manual are for illustration purposes only, and may not

be an exact representation of the application.

4. To take photos and videos using the SHIFT Drone application, a

micro SD card must be inserted in the aircraft. Remove the battery

and insert a micro SD card in the designated direction. Use the

provided micro SD card, or a micro SD card of video speed class 10

or UHS class 1 or higher with a capacity of no more than 32 GB.

aBefore removing the micro SD card, always check that the drone is powered off.

Go to the main screen

Go to the gallery

Drone/controller status information

Setting menu

Lezero Pilot mode

Video quality/frame settings

Wi-Fi setting

Sensor calibration

Version information

Take video/photo

Change video/photo mode

Notice

410

511

612

Using Lezero Pilot Modes

Application “SHIFT Drone” offers various ight modes (Lezero Pilot modes) for users to take semi-

professional videos and photos. When in a ight mode, exercise caution against collisions and

maintain at least 2 m (6.6 ft) away from the drone.

1. To start a Lezero Pilot mode, tap on the button, which stays active only when the drone is

hovering.

2. Choose one of the eight Lezero Pilot modes while referring to the descriptions below.

1 Orbit: The drone ies in orbit.

2 Dolly: The drone ies steadily from right to left.

3Dolly In: The drone starts far and moves near.

4Dolly Out: The drone starts near and moves far.

5 Following: The drone ies while following the target.

6 Horizontal Tracking: The drone tracks the target while in

horizontal ight.

7Yaw Tracking: The drone performs a yaw rotation toward

the target while ying in position.

8 Hero: The drone ies while tracking the target, and orbits

once when the target stops.

3. Long-press the screen to begin free ight in the selected mode. While ying in the selected mode,

you can take photos or videos.

4. A target must be designated in the Following, Horizontal Tracking, Yaw Tracking or Hero mode.

Place the target in the center of the target box, and drag across the screen to designate the target.

When the target is successfully designated, the border of the drag box changes from red to green

and ight begins in the selected mode.

aIn Following or Hero mode, check that the drone altitude is at least 2 m (6.6 ft) before designating a target. The

appropriate altitude for the selected mode is indicated by the icon turning active.

aThe target must stand out from the background in terms of form and color to be successfully detected in a well-lit

environment. The drone switches to hovering if the target is moving too fast or if tracking has failed due to obstacles.

If the target falls inside the red drag box while maintaining a distance similar to the initial distance, tracking resumes

after about two seconds.

5. To stop the selected Lezero Pilot mode, long-press the screen, or hold the controller’s jog button.

6 7 85

8675 6 7 85

This document is a shortened version of the User Manual to help

quickly learn how to use the product. Please make sure to read

the full version to avoid any misuse.

Andere Handbücher für SHIFT RED

Inhaltsverzeichnis

Andere TIE Drohne Handbücher

TIE

TIE CESFD1L Bedienungsanleitung

Beliebte Drohne Handbücher anderer Marken

Ryze

Ryze Tello Bedienungsanleitung

PowerVision

PowerVision PowerRay Bedienungsanleitung

Force1

Force1 rogue F72 Bedienungsanleitung

Zerotech

Zerotech DOBBY Bedienungsanleitung

Protocol

Protocol VIDEODRONE AP Bedienungsanleitung

dji

dji Matrice M210 Bedienungsanleitung

SYMA

SYMA X440 Bedienungsanleitung

SYMA

SYMA X5UW(720P) Bedienungsanleitung

Dynali

Dynali 25 H Leitfaden

dji

dji PHANTOM 4 Bedienungsanleitung

Atlas

Atlas AtlasPRO Bedienungsanleitung

Twodots

Twodots TVVIN BOARD Bedienungsanleitung

GDU

GDU SAGA Bedienungsanleitung

RUKO

RUKO F11 Bedienungsanleitung

Ares

Ares ETHOS QX 130 Bedienungsanleitung

Walkera

Walkera ZHUN Bedienungsanleitung

dji

dji WIND-4 Bedienungsanleitung

Potensic

Potensic D58 Bedienungsanleitung