Timeguard ZV210 Bedienungsanleitung
Installation & Operating Instructions
Programmable
Security Light Switch
Model: ZV210 (Single)
Model: ZV215 (Double)
1
1. General Information
These instructions should be read carefully
and retained for further reference and maintenance.
2. Safety
• Before installation or maintenance, ensure the
mains supply to the light switch is switched off
and the circuit supply fuses are removed or the
circuit breaker turned off.
• It is recommended that a qualified electrician is
consulted or used for the installation of this light
switch and install in accordance with the current
IEE wiring and Building Regulations.
• Check that the total load on the circuit including
when this light switch is fitted does not exceed the
rating of the circuit cable, fuse or circuit breaker.
2
3. Technical Specifications
• 230V AC 50 Hz
• This time switch is of class II construction
and must not be earthed
• Switch Rating: Incandescent Lighting: 40W (min
lamp size) – 300W (max total load)
Low Energy CFL: 20W
LED Lighting: 20W
The LED switching capabilities of this product can be
increased to 200W by the addition of the Timeguard
ZV900 Automatic switch load controller – sold separately
• Minimum Depth of Wall Box: 25mm
• Operating Temperature: 0°C to +40°C
• The ZV215 double security switch will replace any
conventional double or two way switch.
For single switches, use the ZV210 only.
3
4
• Manual ON/OFF switch
• CE Compliant
• Dimensions (H x W x D): 85 x 85 x 38mm
Notes: Not suitable for use with Discharge Lighting
This product can be used both as a normal light
switch and as a security switch. When set in the
security mode it will turn the lights on when it gets
dark, and turn them off again for a chosen period
of time up to eight hours later.
This product requires to be permanently powered
which is achieved through the switched Live.
As such, some LED and CFL lamps may glow or
flash whilst this product is in the “Off” status.
This glow/flash can be eliminated by adding the
Timeguard ZV900 Automatic switch load controller
to the circuit. The ZV900 is sold separately.
lateearly
2
4
6
8
4
5
Manual ON/OFF switch (Doubles as
Security Switch on ZV210)
LED window
(lights when
set in security
mode)
Right Hand Security Switch
(ZV215 only)
Light level
adjuster
Concealed
panel
Light sensing
window
Combined
security switch
and hours on
adjuster
Sliding cover
NOTE: On the ZV215 DOUBLE the right hand switch (red dot)
acts as the security mode.
14
25
36
1
2
3
5
6
4. Connections
ZV215 Double Security Light Switch
ZV210 Single Security Light Switch
Security switch Normal
Switch
ON/OFF and
Two Way (L1)
Common
(COM)
Two Way
only (L2)
ON/OFF and
Two Way (L1)
Common
(COM)
Two Way
only (L2)
ON/OFF and
Two Way (L1)
Common
(COM)
Two Way
only (L2)
lateearly
2
4
6
8
6
5. Security Function
Figure 1 ZV210 Switch Open Figure 2 Switch Closed
7
Testing
• Ensure that the light switch is in the
‘OFF’ position.
• Slide down the front of the cover to expose
the security controls (See Figure 1).
• Turn the light level adjuster fully towards the
early symbol, and then turn the hours on dial
clockwise until the ‘LED window’ glows.
• Emulate darkness by covering the ‘Light sensing
window’, the light will automatically turn ON after
a period of up to two minutes.
• To revert to a normal light switch, turn the hours
on dial fully anti-clockwise, lining up the dot.
8
9
Setting up
• Ensure that the light switch is in the ‘OFF’ position.
• Slide down the front of the cover to expose the
security controls.
• Turn the hours on dial to indicate how many
hours you wish the light to remain on for,
and check the ‘LED window’ is glowing.
• Slide the cover back up.
• The security mode is now set and the light will
automatically turn on at dusk and remain on
for the number of hours you have selected.
This programme will repeat itself every 24 hours.
Note: If you wish to use the security switch
as a normal light switch simply turn the hours
on dial fully anticlockwise, lining up the dot.
If you then wish to use it as a security switch
again please follow the above instructions.
9
10
Adjustment
• If you find that the light switches on when it is
too dark, turn the light level adjuster towards
early and if the light is in operation when
it is too light turn the adjuster too late.
Notes:
• The security switch has a built-in delay function
to ensure that momentary changes in the light
do not switch it on.
• The hours shown on the dial are only approximate
guides, do not expect great accuracy.
• Once the switch has turned on and the programme
has turned OFF after the required number of hours,
it is important not to allow artificial light to fall on it,
followed by a period of darkness. This will fool
the switch into thinking it is dark again and it will
operate. Care should therefore be taken to prevent
light falling onto the switch, e.g. table lamps.
Andere Handbücher für ZV210
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Timeguard Schalten Handbücher
Timeguard
Timeguard ZV700B Handbuch
Timeguard
Timeguard DS1 Bedienungsanleitung
Timeguard
Timeguard ZV210 Bedienungsanleitung
Timeguard
Timeguard Weathersafe IS3N-20 Handbuch
Timeguard
Timeguard TuyaSmart FSTWIFITUTGV Handbuch
Timeguard
Timeguard Weathersafe Vision TGVL01 Handbuch
Timeguard
Timeguard NTTHDA Bedienungsanleitung
Timeguard
Timeguard NTM02 Handbuch
Timeguard
Timeguard ZV210 Bedienungsanleitung
Timeguard
Timeguard TG27 Bedienungsanleitung
