Timewatch TW-D2331 Bedienungsanleitung

TW-D2331

Door Frame Metal Detector

Quick Start Guide

Structure

Dimensions

Dimensions (mm [inch])

Ports

Port (1)

Port (2)

Port description

No. Name Description

1 Power input Connects to the power adapter to get power supply.

2 Ribbon cable port Connects the host to the panels with the ribbon cables.

3 RS-485 A Communication ports.

4 RS-485 B

5 NO Outputs alarm signals to external alarm devices.

6 COM

7 Power input Connects to this port if you need to test the host.

8 Reset button Press and hold the button for more than 5 s to restore the

detector to factory default settings.

9 Ethernet port Connects to network with a network cable.

The distance in this section is the recommended distance. The actual installation distance

depends on the installation site conditions.

●Keep away from moving metal objects

Large moving metal objects should be kept 0.5 m to 2 m away from the detector to avoid false

alarms. Depending on the size of the metal object, the distance between the moving metal

object and the detector might vary.

●Keep away from radioactive electronic interference

The distance between the electronic interference source and the receiving coil should be as large

as possible. The recommended distance is 0.5 m to 4 m. However, the actual distance needs to be

based on specific circumstances. For example, you can go through a metal detector with a source

of interference until the best position is found. Interference can occur from electronic control

panels, radios and computers, image displays, high-power motors and transformers, AC wires,

transistor control circuits, flash fluorescent tubes, arc welding equipment, and more.

●Keep away from conductive electronic interference

Connect the power cord to a line that is not connected to other large loads, such as high-power

motors, because they can cause a large power or voltage shock in the line.

Installing Detector

Step 1 Open the packing box and take out the accessories.

Step 2 Loosen the 4 fixing screws with a crosshead screwdriver to separate the host box and the

beam.

Remove host box

Step 3 Attach the two ribbon cables to the host box.

Attach ribbon cables

Step 4 Feed the ribbon cables through the opening of the beam, thread them out from the two

sides, and then attach the host box back to the beam with the fixing screws.

Attach host box

Step 5 Connect the left ribbon cable to the left panel, and then use the wrench to attach the left

side of the beam to the left panel with two M8 × 60 screws. Connect the right ribbon cable

to the right panel, and then attach the right side of the beam to the right panel with two

M8 × 60 screws.

Attach panels

Step 6 Stand the detector up, connect the power supply, and then secure the power cord to avoid

accidental plug-off during use.

1) Attach the self-adhesive cable zip tie mount to one panel.

2) Connect the power supply.

3) Wind the power cord to the cable zip tie mount, and then feed the cable zip tie through

the mount to tie up the power cord.

Figure 3-5 Connect and secure power cord

Multiple Walk-through Site Installation

When installing multiple devices, space the devices at least 50 cm (d2), and also space the device

and X-ray security screening machine larger than 50 cm (d1). This recommended spacing can make

the little metal objects (such as coin) detected. If you install the devices with space smaller than 50

cm, there might be false alarm. If the spacing needs to be shortened because of limited installation

site, you need to adjust the frequency, lower the security level and sensitivity according to the actual

situation; otherwise, small metal objects might not be detected.

Figure 3-6 Multiple walk-through detectors site installation

Configuration

Controls and Displays

Control panel

Control panel description

No. Name Description

1 LED

display

Two sets of 5-digit LED display.

●By default, the screen displays the number of passes and the number of

alarms.

●After logging in, the screen displays the configuration menu cyclically.

To know the menu order, see "4.2 Menu Description".

2 Buzzer Outputs sound alarm.

3 Indicator Flashes green when the system is working.

4 QR code Scan the QR code on the actual device to get the user's manual.

5 Buttons

●On the home screen, press to log in.

●When configuring parameters, press to save changes

and move on to the next item. Hold the button for 5 s to

cancel and exit.

For setting all-zone sensitivity, resetting counter, automatic

frequency search, factory reset, and diagnosis, you must press

to save or confirm.

Add up numbers or go to the previous item.

Move to the next digit or next item.

●Save the current change.

●Hold the button for 5 s to shut down or start the host.

Inhaltsverzeichnis

Andere Timewatch Metalldetektor Handbücher

Timewatch

Timewatch TW100SE Bedienungsanleitung

Beliebte Metalldetektor Handbücher anderer Marken

Garrett

Garrett MAGNASCANNER CS 5000 Bedienungsanleitung

Valex

Valex 1800200 Bedienungsanleitung

Gauss

Gauss MIL MD Bedienungsanleitung

Velleman

Velleman CS130 Bedienungsanleitung

Sears

Sears 321.596370 Bedienungsanleitung

Eriez

Eriez X8 Bedienungsanleitung

Steinberg Systems

Steinberg Systems SBS-MD-22 Bedienungsanleitung

Zircon

Zircon MetalliScanner m60c Bedienungsanleitung

nalanda

nalanda MD027 Bedienungsanleitung

REV Ritter

REV Ritter CB-7005 Bedienungsanleitung

Minelab

Minelab F1A4 Bedienungsanleitung

Fisher Research Labs

Fisher Research Labs F70 Bedienungsanleitung

Steinberg Systems

Steinberg Systems SBS-MD-12 Bedienungsanleitung

GOLDEN MASK

GOLDEN MASK 5 Bedienungsanleitung

Grizzly

Grizzly YM 203 Bedienungsanleitung

Fisher Research Labs

Fisher Research Labs 1280-X Aquanaut Bedienungsanleitung

Treasure Cove

Treasure Cove Vibra-Probe 560 Bedienungsanleitung

Accurate Locators

Accurate Locators XL16 IMAGER Bedienungsanleitung