Timex T309 Bedienungsanleitung

Model T309

Alarm Clock Radio with

Digital Tuning and Nature Sounds

For additional information, online

registration, and exclusive special

offers please visit our website:

www.sdidirect.com

Installation and Maintenance

Installation

1. Remove the unit and all packing materials from the carton. You should save packing materials in case unit

needs to be returned for service. If you do not wish to save the materials, please dispose of them properly.

2. Place the unit on a stable, level surface, close to an AC outlet, out of direct sunlight, and away from sources

of dust, dirt, heat, water, moisture, vibration, and strong magnetic fields.

3. After installing the batteries (see below) and reading the Maintenance notes, plug the AC cord into an outlet.

“Sure Alarm” Battery Backup Installation

It is strongly recommended that 2 “AAA” batteries be installed into the unit, as directed below, to activate the

“Sure Alarm” battery backup feature. In the event that the AC power cord is disconnected or a power failure

or other interruption occurs, the “Sure Alarm” system will maintain the clock and alarm settings for the life of

the batteries, ensuring that the alarm will sound at the set time (note: while operating on battery power, all set

alarms will sound as a buzzer). When power has been restored, the clock will cease using the battery power,

and will once again operate on AC power.

1. Gently turn the unit over and remove the battery compartment door.

2. Install 2 "AAA" batteries (alkaline batteries are recommended for longer life) into

the battery compartment, making sure that the + and – ends match up with

those inside the compartment.

3. Slide the battery compartment door back on, making sure the door locks into

place, and gently return the unit to its upright position.

Maintenance

1. Place the unit on a level surface away from direct sunlight or sources of excessive heat.

2. Protect your furniture when placing the unit on natural wood or wood with a lacquered finish. A cloth or other

protective material should be placed between the unit and the furniture.

3. Clean the casing with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such

as thinner or similar agents, are not recommended, as they may damage the surface of the case.

4. If the unit is not to be used for a prolonged period, such as a month or longer, remove the batteries to prevent

possible corrosion. Should the battery compartment become corroded or dirty, clean the compartment

thoroughly and replace the batteries.

Battery Compartment

Controls and Indicators

Snooze/Dimmer Bar

Radio On/Sleep Button

Off/Reset Button 

Nature Sounds Button

OFF/RESET ON/SLEEP

SNOOZE / DIMMER

SOUNDS

RADIO

ENTER

Time Set Button 

Date Set / 7-5-2 Button 

Sleep Volume Button 

Radio Band Button 

Reverse/Tuning Button 

Memory Set 1-6 Buttons 

 Radio Alarm Button

 Sounds Alarm Button

 Buzzer Alarm Button

Enter Button

 Forward/Tuning Button

BAND

3412

SLEEP VOL

DATE/7-5-2

TIME RADIO

SOUNDS

BUZZER

RADIO SOUNDSBUZZER

SAT-SUNMON-FRIEVERYDAY

DATE

FM1

FM2

YEAR

SLEEP

Volume Thumbwheel

LCD Display With Indicators

Battery Low Indicator

Radio Frequency /

Calendar Display /

Nature Sounds Indicator

Radio Band Indicator

Buzzer Alarm Indicator Radio Alarm Indicator Nature Sounds Alarm Indicator

7-5-2 Alarm Settings 7-5-2 Alarm Settings

Sleep Volume Indicator

PM Indicator

Clock

Sleep Timer

RADIO SOUNDSBUZZER

SAT-SUNMON-FRIEVERYDAY

DATE AM

FM1

FM2

YEAR

SLEEP

Setting the Clock and Calendar

Setting the Clock

1. Press and hold the Time Set Button until the display begins flashing.

2. Press the Reverse or Forward Button to set the time. Holding a button for a few seconds will

advance or reverse the time rapidly. Set the correct AM/PM time, shown by the PM Indicator on the display.

3. After setting the time, press the Enter Button or wait about ten seconds for the unit to beep twice and

the display to return to the normal mode.

Setting the Calendar

1. It is important to set the correct date in order to use the 7-5-2 Alarm settings. Press and hold the Date

Set/7-5-2 Button until the display flashes and the year replaces the month/day at the bottom of the display.

2. Press the Reverse or Forward Button to set the correct year, and then press the Enter Button.

The unit will beep and the display will show the month and day. Again, press the Reverse or Forward

Button to set the current date.

3. After setting the date, press the Enter Button or wait ten seconds to return to the normal display mode.

Adjusting the Display Backlight

•This alarm clock radio features an adjustable display backlight, with dim, medium, and bright settings. To

select a backlight setting, press the Snooze/Dimmer Bar until the desired brightness is reached.

Operating the Radio

1. Press the Radio On/Sleep Button once to turn on the radio. The display will show the word “On” before

returning to the clock display. The bottom of the display will show the digital radio frequency.

Note: If the Radio On/Sleep Button is pressed more than once, the unit will enter the sleep mode, with

the radio operating on a timer. See Sleeping to Radio with Timer for more information about this feature.

2. Press the Radio Band Button to select a radio band. There are two FM bands (to be used when

programming preset radio station settings) and one AM band.

3. Press the Reverse /Forward Tuning Buttons to find a station to listen to. To scan the radio stations,

hold a button for about three seconds. The radio will rapidly advance to the next strong signal.

4. You may also use the Memory Set 1-6 Buttons to select a preset radio station. See the Programming

Radio Station Settings section below for instructions on programming these settings.

5. Adjust the volume using the Volume Thumbwheel, located on the back of the unit.

6. Press the Off/Reset Button to turn the radio off. The bottom of the display will show the calendar setting.

Programming Radio Station Settings

The radio features 18 programmable radio station settings so you can access your favorite stations quickly.

1. Tune to the first station you wish to program into your preset station settings.

2. Press and hold one of the six Memory Set 1-6 Buttons to program the station into that memory slot.

When the unit beeps, the station setting has been saved.

3. You may continue programming a total of 18 stations into memory: six each into the two FM bands and six

into the AM band. To edit a setting, simply program a new frequency into that memory slot.

Antenna Information and Adjustment

FM – Extend the FM wire antenna to its full length and vary the direction to its strongest signal.

AM – The AM bar antenna is located inside the cabinet. Rotate the unit until you find the strongest AM signal.

Last Station Memory

The tuner always remembers the last station selected before the radio was switched off, and automatically selects

the station again when the radio is turned on.

Listening to the Radio

Sleeping to Radio or Nature Sounds with Timer

Sleeping to the Radio with Timer

Note:For more information about playing the radio, see the Listening to the Radio section of this manual.

1.Press the Radio On/Sleep Button twice to enter the sleep mode.

2.Continue pressing the Radio On/Sleep Button to select a 90-, 60-, 30-, or 15-minute sleep time. When

the display shows the desired sleep time, stop pressing the button. The sleep timer setting remains active

for approximately ten seconds before returning to the standard clock display. The Sleep Volume Indicator

will appear, showing that the radio timer has been activated.

3. Select a radio station using the AM/FM Band Button and either the Memory Set 1-6 Buttons or

the Reverse / Forward Tuning Buttons.

4.Press the Sleep Volume Button to adjust the sleep volume to a comfortable level without affecting the

alarm volume. The Sleep Volume Indicator will show the current sleep volume level. Turning the Volume

Thumbwheel will also adjust the sleep volume, though this will also change the alarm volume.

5.The radio will play for the programmed sleep time and then shut off. To check how much sleep time is

remaining, press the Radio On/Sleep Button once.

6. To turn off the radio before the sleep time has elapsed, press the Off/Reset Button.

Sleeping to Nature Sounds with Timer

1. Press the Nature Sounds Button twice to enter the sleep sounds mode. This sets the sleep timer to

the 90-minute setting. The sleep timer setting remains in the display for approximately ten seconds before

returning to the standard display. The Nature Sounds Indicator will be visible in the LCD display.

2. Continue pressing the Nature Sounds Button to select a 90-, 60-, 30-, or 15-minute sleep timer.

3. Press the Reverse / Forward Tuning Buttons to select one of the four nature sounds.

4. Press the Sleep Volume Button to find a comfortable sleep volume. The Sleep Volume Indicator will

show the current sleep volume level. Adjusting the sleep volume in this way will not affect the alarm volume.

5. To turn off the nature sounds before the sleep time has elapsed, press the Off/Reset Button.

Note:To see the number of minutes remaining on the sleep timer, press the Nature Sounds Button once.

The display will show the Sleep Timer for approximately ten seconds before returning to the normal mode.

Operating the Alarms

This clock radio features an alarm system with three independently operated alarms. Any combination of the

three alarms can be set, including the AM/FM radio alarm, nature sound alarm, and the buzzer alarm. In addition,

each alarm utilizes a 7-5-2 Advance Alarm setting that can be set in advance for a full week, Monday through

Friday, or the weekend.

Setting the AM/FM Radio Alarm

1. Press and hold the Radio Alarm Button until the settings and radio frequency appear on the display.

2. Press the Reverse or Forward Button to set the alarm time.

3. Use the AM/FM Band Button or the Memory Set 1-6 Buttonsto select a radio station to wake up

to. For more information on programming radio stations into memory, see the Programming Radio Station

Settings section of this manual. Adjust the alarm volume using the Volume Thumbwheel.

4. After setting the wake time and sound, you will need to select your 7-5-2 setting. The 7-5-2 setting lets you

set the alarm for a full week, Monday through Friday, or the weekend. Before setting the alarm, be sure that

you have set the date, as shown in the Setting the Clock and Calendar section

. While the display is still

flashing, press the

 Date Set/7-5-2 Button

until the desired setting is shown at the top of the display.

5. After you have programmed the radio alarm, press the Enter Button or wait ten seconds to return to

the clock display. The Radio Alarm Indicator will appear on the display, showing that the alarm is set.

Setting the Nature Sounds Alarm

1. Press and hold the Sounds Alarm Button until the settings and Nature Sounds Indicator appear.

2. Press the Reverse or Forward Button to set the alarm time.

3. Use the Nature Sounds Button to select a nature sound to wake to. There is a choice of four sounds:

Sound #1: Ocean Surf

Sound #2: Forest Spring

Sound #3: Rushing Brook

Sound #4: Summer Wind

4. See Step #4 in the Setting the AM/FM Radio Alarm section for instructions on setting the Nature Sounds

Alarm’s 7-5-2 Advance Alarm.

5. After you have programmed the nature sounds alarm, press the Enter Button or wait ten seconds

to return to the clock display. The Nature Sounds Alarm Indicator will appear on the display.

Operating the Alarms (Continued)

Setting the Buzzer Alarm

1. Press and hold the Buzzer Alarm Button until the alarm setting appears on the display.

2. Press the Reverse or Forward Button to set the alarm time.

3. See Step #4 in the Setting the AM/FM Radio Alarm section for instructions on setting the Buzzer Alarm’s

7-5-2 Advance Alarm.

4. After you have programmed the buzzer alarm, press the Enter Button or wait ten seconds to return to

the clock display. The Buzzer Alarm Indicator will appear on the display, showing that the alarm is set.

Checking Your Alarm Time Settings

To check any of the three alarm settings, press one of the Alarm Buttons twice so that the settings appear

on the display. The display will return to the standard clock display after a few seconds. After you have

checked the setting, be sure the Alarm Indicator still appears on the display, so that the alarm will sound.

Turning Off the Alarms

1. After the alarm sounds, press the Off/Reset Button to turn off the alarm while still maintaining the

programmed 7-5-2 Advance Alarm settings. To turn off an alarm and cancel its 7-5-2 settings, press its

Alarm Button so that its Alarm Indicator no longer appears on the display.

2. If the Off/Reset Button is not pressed, the alarm will sound for an hour before stopping. As long as an

indicator appears on the display, the alarm will sound according to the 7-5-2 Advance Alarm settings.

3. To activate the snooze feature, press the Snooze/Dimmer Bar when the alarm sounds. The alarm will

shut off for approximately nine minutes before sounding again. The feature can be repeated several times

during the one-hour snooze cycle.

Inhaltsverzeichnis

Andere Timex Radiowecker Handbücher

Timex

Timex Ti700 Bedienungsanleitung

Timex

Timex T715 Bedienungsanleitung

Timex

Timex T618 Bedienungsanleitung

Timex

Timex T439S Bedienungsanleitung

Timex

Timex T1251 Bedienungsanleitung

Timex

Timex T1308 Bedienungsanleitung

Timex

Timex T600 Bedienungsanleitung

Timex

Timex T621T Bedienungsanleitung

Timex

Timex T231Y Bedienungsanleitung

Timex

Timex T235 Bedienungsanleitung

Timex

Timex T300 Bedienungsanleitung

Timex

Timex T309TT Bedienungsanleitung

Timex

Timex TW500 Bedienungsanleitung

Timex

Timex T332 Bedienungsanleitung

Timex

Timex T610S - CD Clock Radio Bedienungsanleitung

Timex

Timex T235Y Bedienungsanleitung

Timex

Timex T307S Bedienungsanleitung

Timex

Timex T736 Bedienungsanleitung

Timex

Timex Ti72 Bedienungsanleitung

Timex

Timex T318 Bedienungsanleitung

Timex

Timex T307 Bedienungsanleitung

Timex

Timex T626S Bedienungsanleitung

Timex

Timex Satellite Series Bedienungsanleitung

Timex

Timex T235 Bedienungsanleitung

Beliebte Radiowecker Handbücher anderer Marken

Denver

Denver CRQ-105 Bedienungsanleitung

Audiovox

Audiovox CE90 Bedienungsanleitung

Sony

Sony Dream Machine ICF-C763L Bedienungsanleitung

Sanyo

Sanyo DMP-P6 Bedienungsanleitung

Yamaha

Yamaha ISX-80 Bedienungsanleitung

Pyle

Pyle PLMR20W Bedienungsanleitung

Blaupunkt

Blaupunkt CR7BK Bedienungsanleitung

Philips

Philips AJ3180 Bedienungsanleitung

HoMedics

HoMedics SS-5500-2EU Bedienungsanleitung

RCA

RCA RC66i Bedienungsanleitung

Versaudio

Versaudio Vers Bedienungsanleitung

SOUNDMASTER

SOUNDMASTER UR8100 Bedienungsanleitung

Audiovox

Audiovox CE90 Bedienungsanleitung

Jensen Audio

Jensen Audio JCR-222 - AM/FM Projection Alarm Clock Radio Bedienungsanleitung

Roberts

Roberts ChronoDAB Bedienungsanleitung

AEG

AEG MRC 4132 BT Bedienungsanleitung

Tokai

Tokai TC-155 Bedienungsanleitung

Sony

Sony DREAM MACHINE ICF-C318 Bedienungsanleitung