Timotion ADJUSTME TC15P Bedienungsanleitung

Data sheet for TC15P/TC15S

Control box TC15 P TC15 S

Dimension (L x W x H) 240 x 94 x 39,6 mm 240 x 94 x 39,6 mm

MCU STC15F2K48AS STC15F2K48AS

Switching Power Supply SPM-120Q SPM-120Q SPM-73Q SPM-73

Power consumption in standby < 0.1 W < 0.1 W (bluetooth) < 0.1 W < 0.5 W *

Wake up time 0.1 second < 0.4 second 0.1 second (0.1 second)

Works with TEKxx 01-03-04/TL25 01-03-04/TL25 N/A

Max load, complete frame 120 KG/80 KG 100 KG/60 KG N/A

Rated input AC 100 - 240V 50/60Hz AC 100 - 240V 50/60Hz

Rated output 32 V 32 V

Power consumption in use Full load: 280 W / Average: 160 W Full load: 180 W / Average: 120 W

Duty cycle 10%, Max 1 min. run / 9 min. stop 10%, Max 1 min. run / 9 min. stop

Connection of actuators 2 columns 2 columns

Lifetime 10.000 cycles 10.000 cycles

Soft start/stop function 15 mm 15 mm

Sensi Touch, Built-in** Drive back: 50 mm Drive back: 50 mm

Pre-set of min/max height ✔ ✔

Error tracing ✔ ✔

Exchangeable AC cable ✔ ✔

Safety functions Overload/overcurrent protection Overload/overcurrent protection

Overheat protection Overheat protection

Unbalance protection Unbalance protection

Wireless charger Optional Optional

USB Charger Optional Optional

Bluetooth App, Built-in Optional Optional

Bluetooth App, Dongle Optional Optional

Sensi Touch, Dongle** Optional Optional

Battery Optional N/A

Programmer Optional Optional

* No standby facility - no wake up time

** Note: ➊Sensi touch is blocked for the ﬁrst 30 mm (in both directions) to prevent unintended activation caused by eventually unsynchronization in the start-up phase.

➋For sensi touch to work properly the control box MUST be ﬁxed to the frame

Data sheet for TC15P/TC15S

Sensi touch

Sensi touch is a collision sensor based on sensi-touch technology. Sensi touch is a new hardware based solution that can

detect if a desk has collided with an object, become uneven or has shifted during operation. If one of these conditions are

met, the sensor immediately sends the controlbox a command to stop and reverse the desk 50 mm from raising or lowering.

Sensi touch is sensitive, stable and works independently of load and temperature.

Sensi touch minimize the risk for damages to the sit stand desk if it accidentally collides with obstacles or person during

operation.

Important information

When the tabletop is already misaligned by an obstacle, trying to drive the desk to opposite direction

may trigger sensi touch protection again. Remove the obstacle to operate the desk normally.

Due to the high degree of sensitivity, a work station may stop unexpectedly if it is impacted by the

sudden placement of objects during raising and lowering

Protection may be delayed, or may not be triggered, when the collision occurs with a soft object.

Detection will depend on the object which is involved in the collision.

While reset procedures are being performed sensi touch will not be activated.

Sensi touch is blocked for the ﬁrst 30 mm (in both directions) to prevent unintended activation caused

by eventually unsynchronization in the start up phase.

For sensi touch to work properly the control box or dongle MUST be ﬁxed to the frame.

Adjusting the sensitivity

Note: Only possible with Control boxes produced after 26 August 2019, see label with serialnumber.

Setting method by using handset with display and memory function

1. Press 1 + 2 together for 5 seconds to enter setting mode - The display ﬂashes

2. Press or to adjust the level of sensitivity

0 = deactivating sensi touch

9 = most sensitive

Level 0 1 2 3 4 5 6 7 8 9

Sensitivity Deactivate Sensi touch 200 150 125 100 70

(Default)

50 30 20 10

3. Press 1 + 2 together or leave it for 5 seconds, it will go back to normal operation.

Data sheet for TC15P/TC15S

Troubleshooting by error codes on handset display or by beeps

Perform a reset (synchronization) operation:

Press and hold the up/down buttons simultaneously to run the desk all the way down.

You will hear a Beep when the reset has been completed.

The desk is now operational again.

Error code Buzzer Description Situation Action

0-0 No beep, the display will

show 0-0 in ﬂashing

No built-in sensi touch or

TCS1 is detected

The control box does

not detect built-in sensi

touch or TCS1.

1) Check to make sure

the control box has a built-in T-touch.

2) Check to make sure the cable of the TCS1 is fully

connected to the control box.

3) If adjusting the sensitivity cannot be performed, the

device is defective, and needs to be replaced.

E00

000

No beep Reset is in progress 1. Perform a reset.

2. Make sure to release

the buttons before

the reset has been

completed.

Press and hold the up/down buttons simultaneously to

run the desk all the way down. You will hear a Beep

when the reset has been completed.).

The desk is now

operational again.

E01 3 beeps Overuse protection Operating over the duty

cycle’s normal.

Time and frequency.

Wait for about 5 minutes, and the desk will be opera-

tional again.

E02 2 beeps Unbalanced protection A Desk tilt is detected. 1) Even out the load on the desk and perform a reset.

2) If a reset can’t be performed, or the error keeps being

triggered after a reset, one of the columns is defective

and needs to be replaced.

E03 No beep

Desk reverses 40 mm,

no matter pressing

the button or not

Anti-collision by current Detecting if the desktop

has collided with an

object.

1) If no obstacle occurs, the desk is operational after

reversing,

2) If any obstacle occurs: Remove the obstacle and the

desk is operational.

E04 No beep

Desk reverses 30 mm,

no matter pressing

the button or not

Sensi touch protection Detecting if the desktop

has collided with an

object, become uneven

or has shifted in angles

during operation.

1) If no obstacle occurs, the desk is operational after

reversing,

2) If any obstacle occurs: Remove the obstacle and the

desk is operational.

E11

E12

E13

E14

5 beeps Overcurrent protection of

Overload of

1) Remove the heavy load and the desk will return back

to normal operation.

2) If the desk still cannot be operated normally, perform

a reset and operate the desk.

3) If a reset can’t be performed, or the error keeps being

triggered after a reset, the column (M1, M2, M3 or M4)

is defective and needs to be replaced.

E21

E22

E23

E24

1 long beep No signal-feedback from

Signal is not detected

from

1) Unplug the motor cable, wait for a moment, then

plug it back in.

2) Perform a reset and operate the desk.

3) If a reset can’t be performed, or the error keeps being

triggered after a reset, the column (M1, M2, M3 or M4)

is defective and needs to be replaced..

E31

E32

E33

E34

4 beeps No power consumption

No current is detected

from

1) Unplug the motor cable, wait a moment, then plug it

back in.

2) Perform a reset and operate the desk.

3) If a reset can’t be performed or the error keeps being

triggered after a reset, the column (M1, M2, M3 or M4)

is defective and needs to be replaced.

Please use this QR-code for extended

version of troubleshooting:

Dieses Handbuch passt für folgende Modelle

Andere Timotion Kamerazubehör Handbücher

Timotion

Timotion TBB2 Bedienungsanleitung

Beliebte Kamerazubehör Handbücher anderer Marken

Viltrox

Viltrox EF-NEX Montageanleitung

Calumet

Calumet 7100 Series CK7114 Bedienungsanleitung

Ropox

Ropox 4Single Series Bedienungsanleitung

Cambo

Cambo Wide DS Digital Series Betriebsanleitung

Samsung

Samsung SHG-120 Bedienungsanleitung

Ryobi

Ryobi BPL-1820 Bedienungsanleitung

Aegis

Aegis ABL-36020P Bedienungsanleitung

Pentax

Pentax Data Back Fc Bedienungsanleitung

Fantasea

Fantasea EyeGrabber F Series Bedienungsanleitung

Honeywell

Honeywell HDZ20HD Bedienungsanleitung

EGO

EGO BA1400T Bedienungsanleitung

Sima

Sima SRW-62 Bedienungsanleitung

Shape

Shape A7SSMKIT Bedienungsanleitung

Slide Kamera

Slide Kamera HST-2 Bedienungsanleitung

Power works

Power works 2902613 Bedienungsanleitung

SES

SES SE-2047-2 Bedienungsanleitung

Olympus

Olympus PT-EP05L Bedienungsanleitung

Starlite

Starlite OctoDome nxt Bedienungsanleitung