Tinycontrol POESWG-030 Bedienungsanleitung

Manual

4F1G Switch

4 ports 10/100Mb PoE + 1 port 1Gb

HW:2.1 SW:1.08

4F1G Switch - HW:2.1 SW:1.08 – POESWG-030

www.tinycontrol.eu

4F1G Switch

Managed PoE switch is unique device designed as combination of management switch,

PoE injector and in/out controller.

In opposite to typical PoE switches this one don’t has xed voltage output. This parame-

ter depend on voltage of connected supply. Thanks it switch is very universal and what is

very important power supply uninterruptible is very easy to implementation. Just need

to connect buered uninterruptible power supply with battery (also in oer in our shop).

This solution allow for much higher possible output current, limited to 2A per port.

It is important for momentary spikes of current, often occurring during start up. However

should be remember that high current can damage RJ45 connectors quick - they are not

designed for this applications. All supply parameters can be monitored online, also ICMP

packets returns is monitored by watchdog, if ping don’t reply, output can be reseted.

Switch characterised by unique design - it is only 31mm deep and 1U high. So could be

installed in typical 10” rack as well as in very at, small cabinets for example on corridors.

Other useful feature are 2 logical inputs for monitoring switch surrounds (for ex cabinet

doors) and one voltage output (up to 1A) to remote power dierent devices.

MAIN FEATURES:

•management by WWW or SNMP v2. (all SNMP features available after upgrade)

•rmware upgrade remotely by TFTP

•read data in real time without refresh the page

•ON/OFF power to four passive PoE ports directly from a web page or SNMP

•Watchdog IP on all ports (email notication, trap, reset of power on PoE)

•1 analog measure input

•2 logical inputs

•environment temperature measurement

•voltage measurement: resolution, accuracy ± 0.1 V

•current measurement on each port and consumed by all

•date and time from NTP or manual

•email alert when Watchdog activation

•automatic sending of SNMP TRAP (VCC, temperature, INPD, INPA)

•supported protocols: HTTP, SNMP, SMTP, NTP, ICMP, DNS, DHCP.

•4 ports 100/10Mbit

•1 port 1Gbit

•limit power on the PoE port when 2A current is exceeded.

•VLAN support

•optional mounting on DIN rail

4F1G Switch - HW:2.1 SW:1.08 – POESWG-030

www.tinycontrol.eu

TECHNICAL SPECIFICATIONS

•power supply voltage: 9÷53V

•current consumption at one POE port: 2A (recommended for ling life 1A)

•total power on all ports: ≤ 6A

•power consumption of the switch: <1W

•protection against reverse polarity: YES

•maximal current from transistor output: 1A

•work temperature: –20 do +85 °C

•weight: 0,350kg

•housing high: 1U

•housing sizes without holders: 146 (173 with holders) x 45 x 31 mm

PORTS AND COMPONENTS

POWER – power over plug DC5,5 / 2.1 or terminal block

LED PoE – LED orange, shining denotes activating the power per port PoE

LED LINK – LED green lights means the active link, blinking - data transfer RX / TX

INP1D, INP2D –digital inputs for monitoring, eg. power supply buer, max input voltage 24V.

OUT_T – voltage output transistor performance 1A. The voltage represents switch power

supply voltage.

INP1A – analog input for voltage measurement in the range 0÷3,3V

RESET – press button (eg. paper clip), power on and holding the button down

for approx. 5 seconds restores the factory settings.

(*) - RESET procedure in older versions of the switch (no hole) is described on page 14.

Default user and password is„admin”

IP adress is 192.168.1.200

RESET button hole*

POWER

OUT_T

LED PoE LED LINK

INP1D

INP2D

INP1A

4F1G Switch - HW:2.1 SW:1.08 – POESWG-030

www.tinycontrol.eu

Management by WWW.

1. STATUS

In this window is a summary presented the switch current status.

PoE on/o – species the state of power supply on PoE port: green ON, a red OFF.

PoE [mA] – shows the current consumption of the device.

PoE [W] – shows the power consumption of the device.

INP1A [V] – shows the voltage at the input INP1A.

INP1D State – shows the status of the input INP1D.

INP2D State – shows the status of the input INP2D.

Out_T on/o – shows the status of output Out_T.

4F1G Switch - HW:2.1 SW:1.08 – POESWG-030

www.tinycontrol.eu

2. POE

3. PORTS

any description

max 8 characters

The value in seconds

to return to the OFF state

after switching

PoE POWER ON

The value of the current

drawn by the device

per port PoE

PoE POWER

ON/OFF

selection switches

Power on the PoE port

after reboot / start switch

4F1G Switch - HW:2.1 SW:1.08 – POESWG-030

www.tinycontrol.eu

4. VLAN

Inclusion of of isolation between ports:

In order to isolate trac between the ports, so that the trac was directed only to the

individual ports 1÷4, for example, only port Gigabit P5 you can use the Port based VLAN

Member.

For the example above, only the ports select „M” (if we are able to manage the switch

from each port) and port „5”. For the port „5” we leave all selections (except P5). Then

memorize the setting with „Save” button.

4F1G Switch - HW:2.1 SW:1.08 – POESWG-030

www.tinycontrol.eu

5. WATCHDOG

Email send – sends an e-mail when the watchdog work (will restart power supply on

a port PoE). E-mail contains information about the number of the current restart and

a maximum permissible number of restarts and time of occurrence.

ICMP time – it shows in milliseconds latency response to an ICMP packet.

ICMP fail – number of unanswered response to a query ICMP, followed by a triggering of

the watchdog.

ICMP wait time – response time in seconds.

ICMP send period – the period of time in seconds between successive queries ICMP.

Wait time after restart – the period of time in seconds before sending another query

ICMP after activation of the watchdog.

Restart time – the period of time in seconds for how long it will turn o the power at the

port PoE after activation of the watchdog.

Max restart – maksymalna liczba restartów (zadziałań watchdoga). Gdy ta liczba zostanie

osiągniętą watchdog na danym porcie zostanie wyłączony, żeby w nieskończoność nie

restartować urządzenia, które i tak nie ma zamiaru poprawnie pracować.

POE state – determines the state of power supply to PoE port: red OFF, green ON.

4F1G Switch - HW:2.1 SW:1.08 – POESWG-030

www.tinycontrol.eu

6. SWITCH SETTINGS

The user name and

password to access

the module.

You can disable

authorization.

NTP Server Settings,

Time Interval - time

in minutes, at what time

will be synchronized

with the server.

network settings

conguration.

4F1G Switch - HW:2.1 SW:1.08 – POESWG-030

www.tinycontrol.eu

Congure email

account to send

notications.

Bootloader start

– toggles the switch

in software upgrade mode

Password for SNMP

4F1G Switch - HW:2.1 SW:1.08 – POESWG-030

www.tinycontrol.eu

Software update

In the event that there is a new version of the software it is possible to load such software

for the device.

To install the new rmware to the switch should move it in bootloader mode. The easiest

way to do it from the menu Switch Settings/Others:

1. the „Upgrade Enabled” in the Switch Settings / Access must be enabled.

2. through the „Bootloader start” button.

We have 60 seconds to start uploading via FTP. This will take about 6÷7 seconds and after

this time, the switch will reboot automatically. If at uploading was a mistake, bootlaoder

mode will automatically restart until the correct upload le.

Bootloader start

– toggles the switch

in software upgrade mode

Upgrade Enabled

– It must be enabled to allow the upload

new software

Contents of the instructions is regularly checked and if necessary corrected. If the observations errors or

inaccuracies, please contact us. It can not be ruled out that, despite best eorts, however, some discrepancies

arose. To get the latest version, please contact us or distributors.

Copying, duplication, reproduction whole or in part

without the consent of the owner is prohibited.

Inhaltsverzeichnis

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung