Titan TT-ACP10C02 Leitfaden

INSTALLATION & ASSEMBLY

PORTABLE(AIR(CONDITIONER(

TT-ACP10C02

Installation Safety

●Observe all applicable state and local codes and ordinances.

●Do not use a damaged or non-standard power cord.

●Use caution during installation and maintenance. Incorrect operation can

cause electric shock, resulting in injury or death.

WARNING

Selecting an installation location

Basic requirement

Installing the unit in the following areas may cause it to malfunction:

Air conditioner requirements

1. Keep the air inlet clear of obstacles. Blocking the inlet can affect radiation of the heat

discharge pipe.

2. Select a location where the noise and outflow air emitted by the outdoor unit will not pose

a nuisance.

3. Keep the unit as far away as possible from fluorescent lamps.

4. Do not install this appliance in a bathroom or laundry room.

1. Close to strong heat sources, flammable or explosive vapors or gas (such as sulphur

gas), or projectile objects.

2. Close to high-frequency devices such as welding machines or medical equipment.

3. Coastal areas.

4. Areas containing oil or fumes in the air.

5. Other locations with unusual features that may pose a hazard to the appliance. Consult

your local dealer for help with optimal placement.

Installation Safety

Requirements for electrical connection

Safety precaution

1. Follow all applicable state and local safety regulations when installing and grounding

this appliance.

2. Ensure the safety of the power supply circuit prior to installation.

3. Be sure to properly connect the live wire, neutral wire and grounding wire of the power

socket.

4. Be sure to cut off the power supply before proceeding with any work related to electricity

or safety.

5. Do not connect the appliance to a power source until installation is complete.

6. This air conditioner is a first class electrical appliance. It must be properly grounded by

an electrician or similarly qualified professional. Failure to ensure proper grounding may

result in electric shock.

7. The yellow-green or green wire in the air conditioner is the grounding wire. Do not use it

for other purposes.

8. For appliances with type Y attachment: If the supply cord is damaged, it must be

replaced by the manufacturer, service agent, or service professional in order to avoid

hazard.

WARNING:

Optional

Bracketscrew

Before You Install

Note: Check to ensure that all of the accessories listed here are included with this air

conditioning unit.

Note: The following accessories are not included with all models.

Accessory list

Tools needed for installation

cross screwdriver

gauge

straight screwdriver

scissors

saw

pencil

heat discharge pipe

Joint Window

adapter(top)

Window

adapter(bottom)

remote controll user's manual

battery

(AAA 1.5V)

screw

Foam seal A Insect guard net

wire hook

Adapter

Foam seal B

(adhesive type)

Rain guard

Window kit

Window panel

Exhaust cover

Adjustment panel

Extension panel

Installing Wire Hook

●Assemble the wire hook at the back of the unit with screws (orient the wire

hook as shown in the following figure).

●Wind the power cord around the wire hook.

direction of wire hook is upward

direction of wire hook is downward

screw

wire hook

Removing Collected Water

There are 2 ways to remove collected water:

Use the continuous drainage option from the bottom hole.

■Drainsas follows.

During cooling or drying operations, condensed water will drain to the chassis and

be spattered as it strikes the motor. As the condenser is hot, most of this

condensation will evaporate and drain to the outdoors on its own. Very little

condensed water will accumulate inside the chassis, so you will not need to

discharge the water frequently.

drainage port

Once the chassis is full of water, the unit will buzz 8 times and the "H8" code will

display to remind you to discharge the water:

Move the unit to a suitable place for discharging water. Keep the unit horizontal

when moving; do not tilt.

Remove the rubber plug at the drainage port to discharge the water.

Put the rubber plug back into the drainage port after the water has drained out.

The H8 display will disappear. Once the compressor has been stopped for 3

minutes, the unit will resume operation.

2. Screw the drain connector (included)

to the spout by turning it clockwise.

3. Insert the drainage hose into the

drain connector.

Removing Collected Water

Note:Water can be automatically emptied into a floor drain by attaching a 14mm

inner diameter hose (not included).

Use the continuous drainage option from the middle hole

ATTENTION:

When using the continuous drainage option from the middle hole, place the unit

on a level surface and make sure your garden hose is clear of any obstructions

and is directed downward. Placing the unit on an uneven surface or failing to

attach the hose properly may result in water filling up the chassis, which will

cause the unit to shut off. If this occurs, empty the water in the chassis and

check to make sure that both the unit and the hose are properly set up.

Remove the continuous drain cap (1) by turning it counterclockwise, then remove

the rubber stopper (2) from the spout.

Installation in ADouble-hung Sash Window(Optional)

4. Attach the window panel to the window stool.

Make sure that the exhaust cover is attached to the window panel.

Inner width of the window: 20.5"(520mm)

Use the window panel.

Cut the Foam seal B (adhesive type) to the proper length and attach it to the

window stool and to the bottom of the window sash.

Foam seal B (adhesive type)

1. Connect the rain guards to the insect guard net.

Insert all three projections on each rain guard into the holes in the insect guard net.

2. Attach the combined guard as shown above to the window panel.

Side “A” will now be at the top, as indicated in the diagram.

Push the insect guard net firmly to ensure that its four projections fit into the holes

in the window panel.

Side “A” will now be at the top, as indicated in the diagram.

Hole

Projec-

tion

Insect guard net Rain guard

"A"

Window panel

Projection

"A"

Installation in ADouble-hung Sash Window(Optional)

The window panel cannot be installed in windows less than 20.5" (520mm)

wide,as you will be unable to shut the exhaust cover.

Inner width of the window: 20.5" (520mm)-37.4" (950mm)

Use the window panel and the adjustment panel.

Inner width of the window:37.4" (950mm) - 56.7" (1440mm)

Use the window panel, the adjustment panel and the extension panel.

20.5"

Window panel

Exhaust cover

20.5" - 37.4"

37.4" - 56.7"

(1) Open the window sash and place the window panel on the window sill.

(2) Secure the window panel to the window stool with screws.

(1) Open the window sash and place the window panel on the window sill.

(2) Slide the adjustment panel to fit the window frame width.

(3) Secure the window panel to the sill with screws.

(1) Open the window sash and place the window panel on the window sill.

(2) Slide the adjustment and extension panels to fit the window frame width.

(3) Secure the window panel to the window sill with screws.

Adjustment panel

Extension panel

Adjustment panel

Installation in a Double-hung Sash Window(Optional)

6. Stuff the Foam seal A between the glass and the window to prevent air and insects

from getting into the room.

5. Close the window sash securely against the window panel.

Inhaltsverzeichnis

Andere Titan Klimaanlage Handbücher

Titan

Titan TA-109 Service-Handbuch

Beliebte Klimaanlage Handbücher anderer Marken

Panasonic

Panasonic CS-E12HKEW Bedienungsanleitung

nedis

nedis ACMB1WT7 Bedienungsanleitung

Daikin

Daikin FCFV50A Bedienungsanleitung

Fujitsu

Fujitsu Inverter ASBA30JFC Bedienungsanleitung

Toshiba

Toshiba RAS-M10SMUV-E Bedienungsanleitung

Daikin

Daikin FXLQ20MAVE Bedienungsanleitung

CIAT

CIAT Magister 2 Series Leitfaden

Bestron

Bestron AAC6000 Bedienungsanleitung

Frigidaire

Frigidaire FFRE0533S1E0 Bedienungsanleitung

Samsung

Samsung AS09HM3N Bedienungsanleitung

Frigidaire

Frigidaire CRA073PU11 Betriebsanleitung

Soleus Air

Soleus Air GB-PAC-08E4 Bedienungsanleitung

McQuay

McQuay MCK020A Bedienungsanleitung

Webasto

Webasto Frigo Top 25 DS Bedienungsanleitung

Frigidaire

Frigidaire FAZ12ES2A Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric MSC-GE20VB Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric PLA-M100EA Bedienungsanleitung

Daikin

Daikin Split Sensira R32 Bedienungsanleitung