Titan TTB935HTG Bedienungsanleitung
EN
1800W Heat Gun
WARNING: Read the instructions before using the product!
BX220IM
TTB935HTG
EAN:5059340397610
Original Instructions_TTB93 HTG_GB_V1_220208
55
EN
02
29
28
26
21
19
In more detail...
Product functions
Operation
Care and maintenance
Troubleshooting
Recycling and disposal
18
02
03
13
14
14
Getting started...
Technical and legal information
Your product
Technical specications
Before you start
These instructions are for your safety. Please read through them
thoroughly before use and retain them for future reference.
Let’s
get started...
30
Guarantee
EN
Getting started...
03
Safety information
Safety warnings
1. This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
2. Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children
without supervision.
3. If the supply cord is damaged, it must be replaced by
persons in order to avoid a hazard.
General power tool safety warnings
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to
your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
2. Do not operate power tools in explosive
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
by TITAN
TTB935HTG
EN
04
Getting started...
Safety information
Safety warnings
Electrical safety
1. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
of electric shock.
2. Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
3. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
4. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
5. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
6. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Personal safety
1. Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
A
moment of inattention while operating power tools
may result in serious personal injury.
by TITAN
TTB935HTG
EN
Getting started...
05
Safety information
2. Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
3. Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on the
switch or energising power tools that have the switch
on invites accidents.
4. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
5. Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
6. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
7. If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
Power tool use and care
1. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
2. Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
by TITAN
TTB935HTG
EN
06
Getting started...
Safety information
Safety warnings
3. Disconnect the plug from the power source before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
4. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
5. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
6. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
7. Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
Service
1. Have your power tools serviced by a qualied
repair person using only identical replacement
parts. This will ensure that safety of the power tool is
maintained.
by TITAN
TTB935HTG
EN
Getting started...
07
Safety information
Safety warnings for heat gun
1. The tool must be placed on its stand when not in use.
2. A re may result if the product is not used with care,
therefore
be careful when using the product in places where
there are combustible materials;
do not apply to the same place for a long time;
do not use in presence of an explosive atmosphere;
be aware that heat may be conducted to combustible
materials that are out of sight;
place the product on its stand after use and allow it
to cool down before storage;
do not leave the product unattended when it is
switched on.
Additional safety warnings for heat gun
1. Keep other people as well as pet out of the working
area during operation and before the work area is
cleaned thoroughly.
2. Do not use the product near ammable liquids or in
explosive atmospheres, such as near fumes, gases or
dust. The ameless heat from the product may ignite
the dust or fumes. Remove materials or debris that
may become ignited from work area.
3. Hidden areas such as behind walls, ceilings, oors,
soft boards and other panels may contain ammable
materials that may ignite when using the product in
these locations. Ignition of these materials may not be
readily apparent and could result in property damage
and personal injury. Check these areas before applying
heat. If in doubt, use a different method.
4. Keep away from the hot air outlet. This product
releases an air stream of high temperature that can
cause serious burns and personal injury.
by TITAN
TTB935HTG
EN
08
Safety information
Getting started...
Safety warnings
5. Clean up all paint scrapings and dust. Do not sweep,
dry dust or vacuum to avoid the paint dust will be thrown
up into the air where it can be inhaled or contaminate
other areas. Wet mop oors. Use a wet cloth to clean
all walls, sills and other surfaces where paint and dust
have accumulated.
6. Dispose of paint scrapings properly.
7. Do not obstruct either the air vents or nozzle outlet,
as this may cause excessive heat build up resulting in
damage to the product.
8. Do not direct the hot air blast at persons.
9. Do not aim the hot airow at the same area for prolonged
periods. Working with plastic, paint, varnish or similar
materials may produce easily ammable gases.
10. Safely place the power tool on the storage surfaces
after use and let it cool completely before packing it
away. The hot nozzle can cause damage.
11. Do not leave the switched-on power tool unattended.
12. Keep your work area well-ventilated. The gas and
steam produced during work are often harmful to one’s
health.
13. Do not use the power tool as a hair dryer or attempt to
dry pets.
14. The distance between the nozzle and the workpiece
depends on the material you are working on (metal,
plastic, etc.) and the intended working method. Always
test the amount of air and temperature rst.
15. If operating the power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
by TITAN
TTB935HTG
EN
Getting started...
09
Safety information
16. Safety Warnings for stripping paint. Before stripping
any paint, you should determine whether the paint
contains any lead. Paint containing lead should be
removed by a professional and not by using a heat
gun.
17. Ideally move the workpiece to an outdoor location.
If this is not possible, ensure the work area is well
ventilated.
18. Wear an approved dust respirator mask or dual lter
mask for dust and fumes. Ensure that the mask ts
properly. Disposable paper masks are not adequate.
19. Keep the gun moving when in use to avoid excessive
heat build up.
20. Keep food and drink out of the work area. Wash hands
and face thoroughly before eating or drinking.
The following information applies to professional users
only but is good practice for all users:
Vibration and noise reduction
To reduce the impact of noise and vibration emission,
limit the time of operation, use low-vibration and
low-noise operating modes as well as wear personal
protective equipment.
Take the following points into account to minimise the
vibration and noise exposure risks:
1. Only use the product as intended by its design and
these instructions.
2. Ensure that the product is in good condition and well
maintained.
3. Use correct attachments for the product and ensure
they are in good condition.
4. Keep tight grip on the handles/grip surface.
5. Maintain this product in accordance with these
instructions and keep it well lubricated (where
appropriate).
by TITAN
TTB935HTG
EN
Getting started...
10
Safety information
Safety warnings
6. Plan your work schedule to spread any high vibration
tool use across a longer period of time.
7. Prolonged use of the product exposes the user
to vibrations that can cause a range of conditions
collectively known as hand-arm vibration syndrome
(HAVS) e.g. ngers going white; as well as specic
diseases such as carpal tunnel syndrome. To reduce
this risk when using the product, always wear protective
gloves and keep your hands warm.
Emergency
Familiarise yourself with the use of this product by
means of this instruction manual. Memorise the
safety directions and follow them to the letter. This
will help to prevent risks and hazards.
1. Always be alert when using this product, so that
you can recognise and handle risks early. Fast
intervention can prevent serious injury and damage to
property.
2. Switch off and disconnect from the power supply if
there are malfunctions. Have the machine checked
by a qualied professional and repaired, if necessary,
before you operate it again.
Residual risks
Even if you are operating this product in accordance
with all the safety requirements, potential risks of
injury and damage remain. The following dangers
can arise in connection with the structure and design
of this product:
1. Health defects resulting from vibration emission if the
product is being used over long periods of time or not
adequately managed and properly maintained.
by TITAN
TTB935HTG
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Titan Elektrowerkzeuge Handbücher
Titan
Titan TTI866JSW Bedienungsanleitung
Titan
Titan SF1500XP Installationshandbuch
Titan
Titan Pro V55 Bedienungsanleitung
Titan
Titan TTB883ROU Bedienungsanleitung
Titan
Titan SF1022 Installationshandbuch
Titan
Titan TTB591ROU Installationshandbuch
Titan
Titan TT5MTP26-2 Bedienungsanleitung
Titan
Titan TTI882MLT Bedienungsanleitung
Titan
Titan TT5MTP33BP-2 Bedienungsanleitung
Titan
Titan PR 33 Bedienungsanleitung
Titan
Titan TTB924DBT Bedienungsanleitung
Titan
Titan TTB773HTG Bedienungsanleitung
Titan
Titan TTI913TOR Bedienungsanleitung
Titan
Titan LX-70 Bedienungsanleitung
Titan
Titan 51886 Bedienungsanleitung
Titan
Titan EHS Bedienungsanleitung
Titan
Titan TTB284HTG Installationshandbuch
Titan
Titan SF2843 Installationshandbuch
Titan
Titan TM45FG Bedienungsanleitung
Titan
Titan TTB285JSW Bedienungsanleitung
