Titan TTB911CSW Bedienungsanleitung

Original Instructions –MNL_TTB911CSW_GB_V1_220119

TTB911CSW

1500W Circular Saw

EAN: 5059340349978

WARNING: Read the instructions before using the product!

In more detail...

Product functions

Operation

Care and maintenance

Troubleshooting

Recycling and disposal

Guarantee

Declarations of conformity

Getting started...

Safety information

Your product

Before you start

These instructions are for your safety. Please read through them

thoroughly before use and retain them for future reference.

Let’s

get started...

Getting started...

Safety information

Safety warnings

General power tool safety warnings

WARNING! Read all safety warnings, instructions,

power tool. Failure to follow all instructions listed

serious injury. Save all warnings and instructions

for future reference. The term “power tool” in the

warnings refers to your mains-operated (corded)

power tool or battery-operated (cordless) power

tool!

Work area safety

>Keep work area clean and well lit. Cluttered or dark

areas invite accidents.

>Donotoperatepowertoolsinexplosiveatmospheres,

or dust. Power tools create sparks which may ignite the

dust or fumes.

>Keep children and bystanders away while operating

a power tool. Distractions can cause you to lose control.

Electrical safety

>Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools.

matching outlets will reduce risk of electric shock.

>Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

>Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of

electric shock.

TTB911CSW by TITAN

Safety information

Getting started...

Safety warnings

>Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool. Keep

cord away from heat, oil, sharp edges or moving

parts. Damaged or entangled cords increase the risk of

electric shock.

>When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric

shock.

>If operating a power tool in a damp location is

unavoidable, use a residual current device (RCD)

protected supply. Use of an RCD reduces the risk of

electric shock.

Personal safety

>Stay alert, watch what you are doing and use

common sense when operating a power tool. Do not

use a power tool while you are tired or under the

A moment

of inattention while operating power tools may result in

serious personal injury.

>Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask,

non-skid safety shoes, hard hat, or hearing protection

used for appropriate conditions will reduce personal

injuries.

>Prevent unintentional starting. Ensure the switch

is in the off-position before connecting to power

source and/or battery pack, picking up or carrying

the tool.

switch or energising power tools that have the switch on

invites accidents.

TTB911CSW by TITAN

Getting started...

Safety information

>Remove any adjusting key or wrench before turning

the power tool on. A wrench or a key left attached to

a rotating part of the power tool may result in personal

injury.

>Do not overreach. Keep proper footing and balance

at all times. This enables better control of the power tool

in unexpected situations.

>Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away from

moving parts. Loose clothes, jewellery or long hair can

be caught in moving parts.

>If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection

can reduce dust-related hazards.

>Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause

severe injury within a fraction of a second.

Power tool use and care

>Do not force the power tool. Use the correct power

tool for your application. The correct power tool will

do the job better and safer at the rate for which it was

designed.

>Do not use the power tool if the switch does not turn

it on and off. Any power tool that cannot be controlled

with the switch is dangerous and must be repaired.

>Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from the

power tool before making any adjustments, changing

accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power

tool accidentally.

TTB911CSW by TITAN

Safety information

Getting started...

Safety warnings

>Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the power

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

>Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused

by poorly maintained power tools.

>Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

>Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

Service

>person using only identical replacement parts. This

will ensure that safety of the power tool is maintained.

Circular saw safety warnings

Safety instructions for all saws - Cutting procedures

>DANGER: Keep hands away from cutting area and

the blade. Keep your second hand on auxiliary

handle, or motor housing. If both hands are holding

the saw, they cannot be cut by the blade.

>Keep handles and grasping surfaces dry, clean

and free from oil and grease.Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

TTB911CSW by TITAN

Getting started...

Safety information

>Adjust the cutting depth to the thickness of the

workpiece. Less than a full tooth of the blade teeth

should be visible below the workpiece.

>Never hold the workpiece in your hands or across your

leg while cutting. Secure the workpiece to a stable

platform. It is important to support the work properly to

minimize body exposure, blade binding, or loss of control.

>Hold the power tool by insulated gripping surfaces

when performing an operation where the cutting

tool may contact hidden wiring or its own cord.

Contact with a “live” wire will also make exposed metal

parts of the power tool “live” and could give the operator

an electric shock.

>When ripping, always use a rip fence or straight edge

guide. This improves the accuracy of cut and reduces

the chance of blade binding.

>Always use blades with correct size and shape

(diamond versus round) of arbour holes. Blades that

do not match the mounting hardware of the saw will run

off-centre, causing loss of control.

>Never use damaged or incorrect blade washers

or bolt. The blade washers and bolt were specially

designed for your saw, for optimum performance and

safety of operation.

Further safety instructions for all saws - Kickback

causes and related warnings

>Kickback is a sudden reaction to a pinched, jammed or

misaligned saw blade, causing an uncontrolled saw to lift

up and out of the workpiece toward the operator.

>When the blade is pinched or jammed tightly by the kerf

closing down, the blade stalls and the motor reaction

drives the unit rapidly back toward the operator.

>Do not reach underneath the workpiece. The guard

cannot protect you from the blade below the workpiece.

TTB911CSW by TITAN

Safety information

Getting started...

Safety warnings

>If the blade becomes twisted or misaligned in the cut, the

teeth at the back edge of the blade can dig into the top

surface of the wood causing the blade to climb out of the

kerf and jump back toward the operator.

Kickback is the result of saw misuse and/or incorrect

operating procedures or conditions and can be avoided

by taking proper precautions as given below.

>position your arms to resist kickback forces. Position

your body to either side of the blade, but not in line

with the blade. Kickback could cause the saw to jump

backwards, but kickback forces can be controlled by the

operator, if proper precautions are taken.

>When blade is binding, or when interrupting a cut

for any reason, release the trigger and hold the saw

motionless in the material until the blade comes to

a complete stop. Never attempt to remove the saw

from the work or pull the saw backward while the

blade is in motion or kickback may occur. Investigate

and take corrective actions to eliminate the cause of

blade binding.

>When restarting a saw in the workpiece, centre the

saw blade in the kerf so that the saw teeth are

not engaged into the material. If a saw blade binds,

it may walk up or kickback from the workpiece as the

saw is restarted.

>Support large panels to minimise the risk of blade

pinching and kickback. Large panels tend to sag under

their own weight. Supports must be placed under the

panel on both sides, near the line of cut and near the

edge of the panel.

TTB911CSW by TITAN

Getting started...

Safety information

>Do not use dull or damaged blades. Unsharpened

or improperly set blades produce narrow kerf causing

excessive friction, blade binding and kickback.

>Blade depth and bevel adjusting locking levers

must be tight and secure before making cut. If blade

adjustment shifts while cutting, it may cause binding and

kickback.

>Use extra caution when sawing into existing walls or

other blind areas. The protruding blade may cut objects

that can cause kickback.

Safety instructions for circular saws with inner

pendulum guard - Lower guard function

Safety instructions for all saws - Cutting procedures

>Check the operation of the lower guard spring. If the

guard and the spring are not operating properly, they

must be serviced before use. Lower guard may operate

sluggishly due to damaged parts, gummy deposits, or a

build-up of debris.

Check the lower guard for proper closing before

each use. Do not operate the saw if the lower guard

does not move freely and close instantly. Never

clamp or tie the lower guard into the open position.

If the saw is accidentally dropped, the lower guard may

be bent. Raise the lower guard with the retracting handle

and make sure it moves freely and does not touch the

blade or any other part, in all angles and depths of cut.

The lower guard may be retracted manually only for

special cuts such as "plunge cuts" and "compound

cuts". Raise the lower guard by the retracting

handle and as soon as the blade enters the material,

the lower guard must be released. For all other

sawing, the lower guard should operate automatically.

TTB911CSW by TITAN

Safety information

Getting started...

Safety warnings

>Always observe that the lower guard is covering the

unprotected, coasting blade will cause the saw to walk

backwards, cutting whatever is in its path. Be aware

of the time it takes for the blade to stop after switch is

released.

Additional circular saw safety warnings

>Do not to use any abrasive wheels.

>Use only blade diameter(s) in accordance with the

>Follow the instructions for the blade changing procedure.

>Check the function of all blade guard operations.

>Only cut materials listed in the intended use.

>Use a dust collection system as described within this

instruction manual.

>Clean the product and guarding system properly and

regularly.

Saw blade safety warnings

>Only use saw blades if you have knowledge of how to

use and handle them.

>Pay attention to the maximum rotational speed. The

maximum rotational speed marked on the saw blade

shall not be exceeded.

>Do not use working saw blades which are cracked. Scrap

of saw blades which bodies are cracked. Repairing is not

permitted.

>Clamping surfaces shall be cleaned to remove dirt,

grease, oil and water.

>Do not use loose rings or sleeves to «make up» bore

sizes on saw blades.

>have the same diameter.

TTB911CSW by TITAN

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Titan Gesehen Handbücher

Titan

Titan TTB689CSW Installationshandbuch

Titan

Titan ttb554tas Bedienungsanleitung

Titan

Titan TTB703SSW Bedienungsanleitung

Titan

Titan TTB867JSW Bedienungsanleitung

Titan

Titan TTB674TAS Bedienungsanleitung

Titan

Titan TTB286CSW Installationshandbuch

Titan

Titan TTB545SSW Bedienungsanleitung

Titan

Titan TTB689CSW Installationshandbuch

Titan

Titan SF210JSL Installationshandbuch

Titan

Titan TTB881RSP Bedienungsanleitung

Titan

Titan SF10N1 Installationshandbuch

Titan

Titan SF16G Bedienungsanleitung

Titan

Titan TTB599BNS Bedienungsanleitung

Titan

Titan TTB287CSW Installationshandbuch

Titan

Titan TTB763TAS Bedienungsanleitung

Titan

Titan TTI880RSP Bedienungsanleitung

Titan

Titan TTB364BDS Installationshandbuch

Titan

Titan SF08N5 Installationshandbuch

Titan

Titan SF185R2 Installationshandbuch

Titan

Titan SF2541 Installationshandbuch

Titan

Titan TTB236MSW Installationshandbuch

Titan

Titan SF2841 Installationshandbuch

Beliebte Gesehen Handbücher anderer Marken

RIDGID

RIDGID BS1400 Bedienungsanleitung

ATIKA

ATIKA BWS 400-2 Bedienungsanleitung

RGC

RGC FS20 Bedienungsanleitung

Makita

Makita M2300 Bedienungsanleitung

IMET Spa

IMET Spa BASIC 300 PLUS SHI Bedienungsanleitung

IMET Spa

IMET Spa SIRIO 370 AF-E Bedienungsanleitung

Optimum

Optimum OPTisaw CS 275 Bedienungsanleitung

Makita

Makita BPB180 Bedienungsanleitung

Stihl

Stihl MS 462 C-M Bedienungsanleitung

AEG

AEG TS 250 K Bedienungsanleitung

Meec tools

Meec tools 004665 Bedienungsanleitung

Makita

Makita LS1018L Bedienungsanleitung

Ryobi

Ryobi RCS1400 Bedienungsanleitung

DeWalt

DeWalt DCS391 Bedienungsanleitung

Sealey

Sealey SA72 Bedienungsanleitung

skilsaw

skilsaw SPT88 Montageanleitung

Urrea

Urrea SI810 Abmessungen und Installationsanleitung

EINHELL

EINHELL BKG 210/1 Bedienungsanleitung