TMG TMG-ALS01 Bedienungsanleitung

►www.tmgindustrial.com 1/4 TOLL FREE:1-877-761-2819

TECHNICAL SPECIFICATIONS

Model

TMG-ALS01

Capacity

300 lbs

Minimum Height

220 mm

Maximum Height

720 mm

Hydraulic Oil

ISO VG 15

SAFETY MARKINGS

Congratulations on your purchase of a TMG Industrial hydraulic lift table. With proper care this table should bring you

years of service.

WARNING - Read, study and follow all instructions before operating this device. Failure to heed these instructions

may result in personal injury and/or property damage.

Throughout this manual you will find the following symbols for caution, warning and danger. Pay particular attention to

the notes preceded by these symbols as they are written for your safety. Ultimately, safe operation of this device rests

with you, the operator.

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

This notation is also used to alert against unsafe practices.

Indicates a potentially hazardous situation which, if notavoided could result in death or serious injury.

If you find that the lifting range per stroke is too small: pls lift the table to 2/3 of the maximum height, then

loosen oil plug" and then tighten it.

LIFT TABLE MAIN COMPONENTS

DESCRIPTION QUANTITY

1. Lift table Assembly 1

2. Lifting pedal 1

3. Handle Assembly 1

ASSEMBLY INSTRUCTIONS

1. Your Hydraulic Table is almost completely assembled when you open it. To complete the assembly find the parts

above enclosed with your table.

2. Place the Lifting Pedal (24) into the hole (26), Secure with Bolt M8x25 (25) to fix up.

3. Place the Push Handle (22) into the tube of base assembly (32), secure with Bolt M8x30 (23) to fix up. With brake

thread through the handle assembly and the hole on the base, then with Bolt M8x20 (9) to fix up on the release valve link

bar.

4. Your assembly is complete! Use the rubber mat for the table toop when needed.

►www.tmgindustrial.com 2/4 TOLL FREE:1-877-761-2819

SAFETY PRECAUTIONS

WARNING

WARNING-DO NOT EXCEED RATED CAPACITY

WARNING - Do not use the Hydraulic Table in lifting or moving or persons.

WARNING - This table was designed for use on hard, level surfaces capable of sustaining the load. Use on other than

hard, level surfaces could result in load instability and possible loss of load resulting in property damage and personal

injury.

DANGER - Keep clear of the scissor lifting frame beneath the table for lifting or lowering operations. Scissor lifts have

pinch areas between the frames which can cause serious injury if hands or feet are not well clear of this area.

WARNING - Do not use attachments or adapters of any type to modify this lift.

SAFETY PRECAUTIONS

WARNING - Set the brakes on the rear casters when loading or unloading.

CAUTION - When not in use the table shall be fully lowered. Lock in a safe, dry place and keep away from children.

CAUTION - Do not over-reach. Keep loads evenly balance over the center of the table. Excessive loads on the top or sides

of the table may be unstable with the danger of the table toppling over and causing injury or property damage.

WARNING - Failure to heed these warning may result in personal injury and/or property damage.

GENERAL TIPS FOR SAFE OPERATION

1. Keep work area clean. Cluttered work areas invite injury. Do not use in damp, wet or poorly lit locations.

2. Keep table wiped down and clean. Do not expose to prolonged wet or corrosive conditions.

3. Cover the table and store it in a dry, protected environment.

MAINTAINNENCE

1. Periodically check the tightness of mounting bolts and electrical connections. Remove all dirt or corrosion and always

keep clean.

2. Lubricate the wheels to maintain smooth roiling.

3. Inspect all joints and bolts periodically. Remove from service if any cracking or if the frame is bent or deformed.

TOLL FREE: 1-877-761-28195/6www.tmgindustrial.com

02 03

09 10

14 16

03 03

33 33

39 40

41 42

43 45 44

HYDRAULIC TABLE CART PARTS LIST

►www.tmgindustrial.com 4/4 TOLL FREE:1-877-761-2819

PARTS LIST

DESCRIPTION

QTY

DESCRIPTION

QTY

Pump

Lifting pedal

Bolt M8x25

Shaft Retaining ring 12

Lifting pedal assembly

Lift frame

Caster assembly

Shaft

Shaft retaining 8

Shaft Retaining ring 8

Bushing

Wheel

Bolt M8x20

Base assembly

Nut M8

Bolt M8x22

Washer 8

Zipper part

Spring washer 8

Step handle

Shaft

Pin 6x22

Shaft retaining ring 16

Bearing

Rubber mat

Bushing

Shaft retaining ring 10

Shaft

Connecting plate

Pin 8x20

Baffle

Bumper

Bolt M10x40

Top table

Nut M10

Brake handle

Washer 10

Bolt M8x30

Inhaltsverzeichnis

Andere TMG Hebesystem Handbücher

TMG

TMG TMG-ALF90 Bedienungsanleitung

TMG

TMG TMG-ALS61 Bedienungsanleitung

TMG

TMG TMG-TPL45 Bedienungsanleitung

TMG

TMG TMG-1000PML Bedienungsanleitung

TMG

TMG TMG-ALS03 Bedienungsanleitung

TMG

TMG TMG-ALS05 Bedienungsanleitung

TMG

TMG ALPHA 3.5 Stücklistenhandbuch

TMG

TMG TMG-ALT95 Bedienungsanleitung

TMG

TMG TMG-1500PML Bedienungsanleitung

TMG

TMG TMG-ALSP60 Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung