Toa D-901 Gebrauchs- und Pflegehandbuch

D-901DIGITAL MIXER

FIRMWARE UPDATE MANUAL

The D-901's firmware can be updated using the software program (D901PCvxxxe_fxxx.exe)*1made available

on the TOA internet site [http://www.toa-products.com/]. To update the firmware, download the software

program to install it into your PC. (For the installation procedure, refer to the "D901 PC Software Instruction

Manual" also available on the same site.)

The firmware update is performed by using the D-901 Firmware Update Utility program simultaneously

installed with the D-901 PC Software.

Follow the procedure for the firmware update below.

After updating the firmware, use the latest D-901 instruction manual that can also be downloaded from the

website above.

*1The software version number can be confirmed at the xxx indication. For example when the PC Software

version is 3.00 and Firmware version is 3.01, it is indicated as "D901PCv300e_f301.exe.

Step 1. Connect both RS-232C ports of the D-901 and the PC using a 9-pin straight cable (male-to-female

cord).

Step 2. Make RS-232C port settings at the D-901.

Set the control mode to "UPDATE*2" and the transmission rate to "115200 bps" (recommended).

*2Set "NONE" for the version 1.xx firmware.

2-1. Press the UTILITY key on the D-901's front panel.

The Stereo Link setting screen is displayed.

UTILITY

[UTY] STR LINK

[IN 1] [IN 2

]

PARAMETER

PUSH-ENTER

CHANGE

[UTY] RS-232C

MODE PC CTRL

[UTY] RS-232C

MODE UPDATE

[UTY] RS-232C

MOD E NONE

(When the version is 1.xx)

[UTY] RS-232C

38400bps

[UTY] RS-232C

115200bps

PARAMETER

PUSH-ENTER

CHANGE

2-2. Press the shift key several times until the RS-232C port setting screen is displayed.

The number of key depressions depends on the D-901's module configuration.

2-3. Rotate the Setting knob to set the Control mode to "UPDATE*2."

2-4. Press the shift key to display the setting screen of the RS-232C port transmission rate.

2-5. Rotate the Setting knob to set the transmission rate to "115200 bps" (recommended).

Step 3. Select the menu items [Start →Program →TOA Digital Audio Control →Update D-901 Firmware] on

the PC.

The D-901 Firmware Update screen appears.

The default communication settings are as follows:

Communication port: COM 1

Baud rate: 115200 bps

Unless otherwise necessary to change, follow Step 6.

To change the settings, follow Step 4.

Step 4. Click the [Comm Settings] button.

The Comm Settings screen appears.

Step 5. Set the PC's Com port the D-901 is connected to, and the Speed (baud rate*) equal to the D-901's

RS-232C transmission rate.

Click [OK], then the Comm Settings screen closes.

* Set the same value as that set in Step 2.

Step 6. Click the [Update] button of the D-901 Firmware Update screen.

The firmware update starts being transferred from the PC to the D-901.

200412

The following screen appears after the update ends.

[If "No Reply" is displayed]

If the screen on the right appears after clicking the

[Update] button, confirm the following:

• RS-232C cable specification and connection

Check that 9-pin straight cable (male - female) is

used.

• RS-232C settings at the D-901 (Step 2)

Check that the control mode is set to UPDATE*.

* Set "NONE" for the version 1.xx firmware.

• PC communication settings (Step 4)

After confirming all the above items, follow the procedure from Sep 3 again.

If the same "No Replay" indication still appears in this Step 6, turn the D-901's power off, and on

again. Then, follow the steps again from the beginning.

Step 7. Turn the D-901's power off, and on again.

Confirm the firmware version number that appears on the LCD screen

at the unit's power-on. When the new version number is indicated,

update has been completed correctly.

Using the Utility key can also indicate the firmware version number on

the LCD screen.

[If an error indication appears on the D-901's LCD screen] (See the screens below.)

Click the Update button of the D-901 firmware update screen, and "Complete!" is displayed on its

screen. Then, the error indication disappears.

After confirming its disappearance, restart the procedure from Step 2 without turning the D-901's

power off.

<<SYSTEM ERROR>>

TYPE : f f 00

<<SYSTEM ERROR>>

TYPE : f f 01

Step 8. Click the [Exit] button to end the firmware update.

TOA D- 901 Ser i es

Sof tware Ver3.00

[ UTY ] VERS I ON

3.00.00

Andere Handbücher für D-901

Inhaltsverzeichnis

Andere Toa Musikmixer Handbücher

Beliebte Musikmixer Handbücher anderer Marken

Neve

Neve 8816 Bedienungsanleitung

Mackie

Mackie Onyx Analogue Mixer Bedienungsanleitung

Behringer

Behringer EUROPOWER PMP518M Bedienungsanleitung

Peavey

Peavey S-32 Sanctuary Series Bedienungsanleitung

Rane

Rane MP 4 Bedienungsanleitung

True

True T9 Touchscreen Console Bedienungsanleitung

Studiomaster

Studiomaster Air Pro 24 Bedienungsanleitung

Pioneer

Pioneer SVM 1000 - Audio/Video Mixer Bedienungsanleitung

Roland

Roland M-160 Bedienungsanleitung

Yamaha

Yamaha MR1642 Bedienungsanleitung

Ecler

Ecler MAC40v Bedienungsanleitung

Pioneer

Pioneer DJM 909 - Battle Mixer W/Effects Bedienungsanleitung

Veeder-Root

Veeder-Root TLS-350 Series Bedienungsanleitung

Alto

Alto APM80.QUAD Bedienungsanleitung

Omnitronic

Omnitronic PM-211 Bedienungsanleitung

SoundCraft

SoundCraft B400 Bedienungsanleitung

Roland

Roland SoundCanvas SC-8820 Bedienungsanleitung

CARVIN

CARVIN RX 1200 Bedienungsanleitung