Toa SX-2000 SERIES Bedienungsanleitung

OPERATING INSTRUCTIONS

MATRIX SYSTEM SX-2000 SERIES

Thank you for purchasing TOA's Matrix System.

Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.

2
TABLE OF CONTENTS
1. NOMENCLATURE AND FUNCTIONS
Front ....................................................................................................................... 1-2
2. OPERATING SETTINGS DATA (DIP Switch 2 Operation)
2.1. Using Settings Data ........................................................................................ 1-4
2.2. Inserting a CF Card ......................................................................................... 1-4
3. OUTPUTTING LOG DATA (Operating DIP Switches 1 and 2) ....... 1-5
1. NOMENCLATURE AND FUNCTIONS
Front ....................................................................................................................... 2-2
Fluorescent Display ............................................................................................... 2-4
2. KEY LOCK SETTINGS AND CANCELLATION 
(DIP Switch 1 Operation) ............................................................................. 2-5
3. OPERATING THE MENU SCREEN
3.1. Menu Screen Operation Keys ......................................................................... 2-6
3.2. Menu Screen Hierarchical Chart ..................................................................... 2-7
3.3. Explanations of Menu Screen Items
3.3.1. Information Display (AI1) ...................................................................... 2-8
3.3.2. Operation Status Display (AI3) ............................................................. 2-9
3.3.3. Equipment Information Display (AI11) ................................................ 2-12
1. NOMENCLATURE AND FUNCTIONS
Front ....................................................................................................................... 3-2
Fluorescent Display ............................................................................................... 3-4
2. KEY LOCK SETTINGS AND CANCELLATION 
(DIP Switch 1 Operation) ............................................................................. 3-5
3. OPERATING THE MENU SCREEN
3.1. Menu Screen Operation Keys ......................................................................... 3-6
3.2. Menu Screen Hierarchical Chart ..................................................................... 3-7
3.3. Explanations of Menu Screen Items
3.3.1. Information Display (AO1) .................................................................... 3-8
3.3.2. Operation Status Display (AO3) ........................................................... 3-9
3.3.3. Equipment Information Display (AO13) .............................................. 3-12
CHAPTER 3: SX-2000AO AUDIO OUTPUT UNIT
CHAPTER 2: SX-2000AI AUDIO INPUT UNIT
CHAPTER 1: SX-2000SM SYSTEM MANAGER

3
NOMENCLATURE AND FUNCTIONS
1. RM-200S ......................................................................................................... 4-2
2. RM-210 ........................................................................................................... 4-4
INDICATOR STATUS
1. Indicators During Zone Selection .................................................................... 4-5
2. Talk Key Indicators ......................................................................................... 4-6
3. Indicators When Changing BGM Patterns ...................................................... 4-6
BROADCASTING
1. Broadcasting from the SX-2000AI or SX-2000AO .......................................... 5-2
2. Broadcasting from the RM-200S and RM-210 ................................................ 5-3
2.1. Example of broadcasting to the selected (pattern-designated) zone .... 5-4
2.2. Example of broadcasting to the selected (individual) zone ................... 5-5
2.3. Example of BGM broadcasting ............................................................. 5-6
2.4. Making urgency all-zone calls 
(when placing the CPU in an "off" condition) ........................................ 5-7
ADJUSTING INPUT/OUTPUT VOLUME ................................................. 5-8
MONITORING INPUT/OUTPUT CHANNELS ......................................... 5-9
CHAPTER 5: OPERATION
CHAPTER 4: REMOTE MICROPHONE RM-200S
REMOTE MICROPHONE EXTENSION RM-210

Chapter 1

SX-2000SM SYSTEM MANAGER

The SX-2000SM System Manager is capable of performing audio signal routing and priority

control for the entire SX-2000 system. It comes with 8 control inputs, 8 control outputs, failure

status output, failure status input, and other functions that include keys, access indicators, mode

indicators and failure indicators, enabling a wide range of control and status monitoring.

Each function can be set using the SX-2000 Setting Software, and the settings data saved to a

Compact Flash (CF) card. By inserting the programmed CF card into the SX-2000SM, each

control can be performed for the entire system. It is also possible to record the entire system's

operation log and store its contents on the CF card as an operation log.

The SX-2000SM is a 1U-size* unit that can be mounted in an EIA equipment rack. It has two

power supply inputs, one of which can be connected to a backup power source to protect against

power failures.

*1U size = 44.5 mm (standard size)

1-2

Chapter 1: SX-2000SM SYSTEM MANAGER

Protective cover

Inside of the protective cover

10 11 12

13 14

15 16 18 1917

1. NOMENCLATURE AND FUNCTIONS

[Front]

1. LAN Indicator [LAN] (Green)

Lights when the LAN connector on the rear panel

is connected, and flashes during LAN

communications.

2. SX Link A Indicator [SX LINK A] (Green)

Lights when the SX Link A connector on the rear

panel is connected, and flashes while

communications are being performed via the SX

Link Connector A.

3. SX Link B Indicator [SX LINK B] (Green)

Lights when the SX Link B connector on the rear

panel is connected, and flashes while

communications are being performed via the SX

Link Connector B.

4. Emergency Indicator [EMERGENCY] (Red)

Lights when the CPU turns off (p. 5-7), and

flashes when a 24 V emergency cutoff* state

occurs involving any SX-2000AO within the

system.

* In the SX-2000 system, a 24 V emergency cutoff

input terminal that allows control of an

emergency audio input is provided on the SX-

2000AO's rear panel. When the SX-2000 system

is combined with an emergency broadcast

system, a 24 V DC is normally kept being

supplied to this emergency cutoff input terminal

and is cut off (24 V emergency cutoff function) in

emergency situations. This interrupts the

general-purpose broadcast from the SX-2000,

allowing the emergency broadcast system to

override it. (For details, see the separate

Installation Manual.)

5. CPU OFF Indicator [CPU OFF] (Red)

Lights when the CPU turns off (p. 5-7).

6. Standby Indicator [STANDBY]

This indicator is not used.

7. General Indicator [GENERAL] (Yellow)

Lights when the CPU turns off (p. 5-7) or when a

failure is detected in the SX-2000SM. Flashes

when a failure is detected in the system.

8. CPU Indicator [CPU] (Yellow)

Lights when the CPU turns off (p. 5-7) or when a

failure is detected in the SX-2000SM.

9. SX Link Indicator [SX LINK] (Yellow)

Flashes when cables are not connected to the

rear panel-mounted SX Link Connectors A and

10. Fault Ack Key [FAULT ACK]

Stops the buzzer from sounding when failures

are detected in the SX-2000SM.

1-3

Chapter 1: SX-2000SM SYSTEM MANAGER

11. Fault Reset Key [FAULT RESET]

Pressing this key resets the SX-200SM's failure

information (the buzzer and fault indicators).

12. Lamp Test Key [LAMP TEST]

Used to test each indicator on the front panel of

the SX-2000SM.

All Mode and Fault indicators (4) – (9) remain lit

as long as this key is pressed.

13. Power Indicator [POWER] (Blue)

Lights when the power is switched on.

14. RUN Indicator [RUN] (Green)

Continuously flashes.

Extinguishes when the CPU turns off (p. 5-7).

15. Reset Key [RESET]

Pressing this key reactivates the SX-2000SM.

The entire system, including the SX-2000AI and

the SX-2000AO, is reactivated.

Notes

• Reactivating the system stops broadcasts

currently in progress.

• Do not keep pressing the key for over 1

second. The unit cannot operate.

If the unit operation is suspended, press the

Reset key for less than one second again.

16. USB Port [USB]

This port is not used.

17. CF Card Access Indicator [ACCESS] (Green)

Flashes while reading from or writing to a CF

card.

Note

Do not remove and reinsert the CF card nor

operate the DIP switch (19) while this indicator is

flashing.

18. CF Card Slot [CF CARD]

Use this slot to insert a CF card to operate

settings data or write log data to the card.

• For settings data operation, see p. 1-4.

• For the method of writing log data, see p. 1-5.

Note

Removing and reinserting the CF card requires

DIP switch settings. If the CF card is removed

and reinserted without performing correct DIP

switch settings, this may cause settings data loss

or damage the card

19. DIP Switch [SETTING]

Used to perform CF card access settings, read

log data, and operate settings data (p. 1-4).

• Switch 1

ON: Allows log data to be written into a CF card.

OFF: Select this position normally.

• Switch 2

ON: Access to the CF card stops.

OFF: Select this position normally.

• Switches 3 – 8

These switches are not used.

Note

Switches 1 – 8 are set to the OFF position by

default. Set all these switches to OFF when

using the system under normal use conditions.

1-4

Chapter 1: SX-2000SM SYSTEM MANAGER

2. OPERATING SETTINGS DATA (DIP Switch 2 Operation)

2.1. Using Settings Data

The SX-2000 system is operated by storing the data set using the SX-2000 Setting Software on a CF card

and inserting the card into the SX-2000SM.

Note

Be sure to insert the CF card containing the settings data into the CF card slot.

2.2. Inserting a CF Card

The DIP switch must be set when inserting the CF card into the SX-2000SM.

Follow the procedure below:

Note

Do not operate the DIP switch while the CF card access indicator inside the protective cover is flashing.

Step 1. Remove the protective cover on the SX-2000SM's front panel by unscrewing it with a Phillips

screwdriver.

Protective cover

Screw

DIP switch

CF card slot

Inside of the protective cover

CF card access indicatorReset key

Step 2. Confirm that the CF card access indicator is unlit and the DIP

switch 2 is set to OFF.

This condition allows the CF card to be inserted.

Step 3. Insert the CF card on which the settings data has been stored

into the CF card slot.

Step 4. Press the Reset key.

The SX-2000 system is reactivated.

Note

Reactivating the system stops broadcasts currently in progress.

Step 5. Replace the protective cover.

Note: DIP switch 2 is set to

OFF by default.

12345678

1-5

Chapter 1: SX-2000SM SYSTEM MANAGER

12345678

3. OUTPUTTING LOG DATA (Operating DIP Switches 1 and 2)

By writing the SX-2000 system's operation log to a CF card in the ".s2l" file format and displaying this data on

a PC installed with the SX-2000 Setting Software, the data can be output as an Excel CSV file. Log data

saved to a CF card is automatically assigned the file name "SX2000_x.s2l," in which the "x" represents a

number from 0 to 9 indicating the order in which the logs have been saved. If more than ten files are saved,

the oldest files (those with lower numbers) are overwritten. The newness or oldness of a file may be

ascertained by checking its date. Shown below is the procedure for writing the SX-2000SM's log data to the

CF card.

Notes

• When storing log data on a CF card, confirm in advance that it has at least 15 megabytes of free space.

• Do not operate the DIP switch while the CF card access indicator inside the protective cover is flashing.

• Reactivating the SX-2000SM erases the log data temporarily stored in SX-2000SM memory.

So, when storing log data on a CF card, be sure to perform that before activating the SX-2000SM.

Step 1. Remove the protective cover on the SX-2000SM's front panel unscrewing it with a Phillips

screwdriver.

Protective cover

Screw

DIP switch

CF card slot

Inside of the protective cover

CF card access indicatorReset key

Step 2. Set Switch 1 to ON.

Log data is saved to the CF card at this time.

Step 3. Confirm that the CF card access indicator has extinguished, then

set Switch 1 to the OFF position.

Step 4. Set Switch 2 to ON.

Access to the CF card stops, allowing the card to be removed.

Step 5. Remove the CF card from the card slot.

Step 6. Insert the CF card into the PC's card slot and start the SX-2000

Setting Software.

Confirm the log data using the SX-2000 Setting Software.

For details, see the separate Setting Software Instructions,

"Utility."

12345678

Note: Switch 1 is set to OFF

by default.

1-6

Chapter 1: SX-2000SM SYSTEM MANAGER

Step 7. Set Switch 2 to OFF.

The CF card can be inserted.

Step 8. Insert the CF card with the saved settings data into the SX-

2000SM's CF card slot.

Step 9. Press the Reset key.

The SX-2000 system is reactivated.

Note

Reactivating the system stops broadcasts currently in progress.

Step 10. Replace the protective cover.

12345678

Chapter 2

SX-2000AI AUDIO INPUT UNIT

The SX-2000AI is an audio input unit for use with the SX-2000 system. It features modular

construction that allows it to handle from 2 to 8 inputs per unit. It can be mounted in an EIA

equipment rack (2U size*), and multiple units can be installed in different locations with no need

to centralize in one location.

Audio signals are transmitted digitally to the audio output unit, but an analog audio output

function (1 channel) enables simultaneous all-zone calls for use in emergency situations.

The SX-2000AI is equipped with 2 power inputs, allowing the connection of a backup power

supply for use during power failures. Level meters provided for each input channel allow

monitoring of audio input levels. Input volumes can be adjusted using the input volume controls

on the front panel, however the maximum volume when the volume control knob is rotated fully

clockwise is a default value defined by the SX-2000 Setting Software.

Also, any input channel can be monitored using the internal speaker. The key lock function,

designed to prevent accidental mistaken operation, can disable input volume control and monitor

volume control settings.

* 1U size = 44.5 mm (standard size)

Andere Handbücher für SX-2000 SERIES

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toa Stereoanlage Handbücher

Toa

Toa SB-46S Bedienungsanleitung

Toa

Toa SB-38S Bedienungsanleitung

Toa

Toa SB-30S Bedienungsanleitung

Beliebte Stereoanlage Handbücher anderer Marken

LG CM3330B Bedienungsanleitung

Sony

Sony SS-CEP50 Bedienungsanleitung

Cetacea Sound

Cetacea Sound CVS-II Bedienungsanleitung

Denon

Denon UCD-250 Bedienungsanleitung

Sanyo

Sanyo DC-MX41i Bedienungsanleitung

Sharp

Sharp CD-ES600V Bedienungsanleitung

Exibel

Exibel BDX600-UK Bedienungsanleitung

Sanyo

Sanyo DC-F320 Bedienungsanleitung

Philips

Philips FWM583X Bedienungsanleitung

Sharp

Sharp CD-C462 Bedienungsanleitung

Onkyo

Onkyo CBX 300 - CD / MP3 Clock Radio Bedienungsanleitung

Aiwa

Aiwa XR-EM70 Bedienungsanleitung

Cyrus

Cyrus Lyric Bedienungsanleitung

Philips

Philips MCM159/98 Bedienungsanleitung

Philips/Magnavox

Philips/Magnavox Magnavox FW 62C Bedienungsanleitung

RCA

RCA RS3965SB Bedienungsanleitung

Sharp

Sharp XL-UH240 Bedienungsanleitung

Philips

Philips FW 690 Bedienungsanleitung