Toho Electronics TTM-P4W Series Bedienungsanleitung

TOHO ELECTRONICS INC.

Program Controller TTM-P4W Series

Instruction Manual

Thank you for purchasing our Program Controller TTM-P4W Series. Please read this

Instruction Manual carefully to use the product correctly. TTM-P4W Series is a

simplified program controller which enables program operation of up to "Patterns x

Steps = 64".

Contents

1. Cautions on Use................................................................... 1

2. Name and Size of Each Part................................................ 2

3. Wiring.................................................................................. 4

4. Terms and Functional Description ...................................... 5

5. Before Program Operation .................................................. 8

6. Operation Flow and Parameter Description ........................ 9

7. Setting and Display Ranges............................................... 20

8. Specifications and Rating.................................................. 21

9. Maintenance and Inspection.............................................. 23

1. Cautions on Use

For safety purpose, following symbols are used in this manual.

The case that a user may receive fatal damage, electric shock, or severe burn

injury when the product is incorrectly used.

The case that a user may receive minor damage or the equipment may get

damage.

Verify correct wiring before turning on electricity since incorrect wiring may

cause an equipment failure or a fire. Modification of this equipment may cause

malfunctioning or a fire. Do not add modification on this equipment.

Wiring: Do not use empty terminals for irrelevant purposes.

Operation: Do not use a sharp-pointed tool for operating keys.

- Hand over this operation manual to a person who actually operates the product.

- Do not reprint or duplicate this manual without permission.

- Content of this manual may be subject to modification without prior notice.

- We are not liable for any faults arising from misuse of the product.

Verification of the product

1) Verification of the model:

Refer the model name printed in the packing box to the order sheet.

2) Verification of accessories:

Instruction Manual (this manual) ......................... 1 copy

Mounting attachment............................................ 1 pc

3) Model

ＴＴＭ－Ｐ４Ｗ－０－□－Ａ□Ｅ□

①②③④⑤⑥⑦

Item

Description

①

Model

P4W

48×48mm

②

Input

Thermocouple(K､J､R､T､N､S､B)

RTD(Pt100)

③

Control Output 1

Relay Contact

Select

One

SSR Drive Voltage

Current 4-20mA DC

④

Time Signal Output/Event Output 1

Relay Contact

⑤

Run Signal Output/Event Output 2/

Control Output 2

Relay Contact

Select

One

SSR Drive Voltage

⑥

External Input

DI (Non-voltage contact input)

⑦

Communication

RS-485

※"I" in Control Output1 can be switched to transmission output by parameter setting.

Prior to control operation

- Non-volatile memory is used for storing settings, which stays in the storage even when the power is

cut.

Warning

Caution

Warning

Caution

2. Name and Size of Each Part

2.1 Name of each part

LED Lamp

RUN: Lights during operation mode

OUT1: Lights when control output 1 is ON (closed) and

turns off when control output 1 is OFF (open).

OUT2:Lights when control output 2 is ON (closed) and

turns off when control output 2 is OFF (open).

AL1: Lights during Event Output 1.

AL2: Lights during Event Output 2.

COM: Turns off when the product model "Communication"

is not selected.

Lights when the product model "Communication" is

selected. Blinks during communication.

DI: Lights when the external input is ON (closed) and turns off when the external input is

OFF (open).

Operation Key

RUN/RESET key: RUN/RESET operation key

PATT./STEP key: PATTERN/STEP operation key

△key: Setting value and parameter change key

▽key: Setting value and parameter change key

For the details of operation, see "6. Operation Flow and Parameter Description."

2.2 External dimensions and panel cut size

3. Wiring

3.1 TTM-P4W series

3.2 Caution on wiring

Before wiring, be sure to turn off the power supply. Otherwise, you may get an

electric shock.

This equipment does not execute control operation for about 4 seconds after the

power is turned on. (Control output does not work. during the period)

Pay attention when you use this equipment for interlock circuit.

Confirm the wirings of the input terminal, power terminal, and optional terminal

by reading the label at the side of the equipment.

- Use crimping terminals matching to M3.5 screws. Also, when you wire to the central terminals,

tighten the wire directly.

- As for wire rods to be used for connecting this equipment with a thermocouple, use a specific

compensating lead wire or wire itself.

- When you use this equipment near the source of noise, use a shielded wire. Also, do not wire the

input/output line in the same duct or wire conduit.

- Leave the input/output signal line more than 50 cm away from the power and load lines.

Communication

(RS-485)

Warning

Caution

4. Terms and Functional Description

4.1 Set the Number of Patterns

- The maximum number of steps are determined depending on the number of patterns.

- The relationship between the number of patterns and the maximum number of steps is as shown in the table below.

Number of Patterns

Maximum number of Steps

4.2 Event Output 1 / Event Output 2

1. Deviation upper/lower limit

5. Absolute value upper/lower limit

ALd

ALL ALH

△

０°C

ALd ALd

ALL ALH

2. Deviation upper limit

6. Absolute value upper limit

ALd

ALH

△

０°C

ALd

ALH

3. Deviation lower limit

7. Absolute value lower limit

ALd

ALL △

０°C

ALd

ALL

4. Deviation upper/lower limit range

8. Absolute value upper/lower limit range

ALd

ALL ALH

△

ALd

ALd ALd

０°C ALL ALH

: Temperature Event Output operation range ALL: Event Output lower limit setting ALH: Event Output upper limit setting

ALd: Event Output sensitivity

4.3 Wait operation

If the measured value (PV) has not reached the Wait Zone after the step time has elapsed,

the next step will not start.

However, after the wait time has elapsed, the next step begins.

At the wait operation, the indication at SV blinks.

: Wait Zone... This means the deviation area between SV(Setting Value) and

PV(Process Value) enable to start next step.

RAMP STEP SOAK STEP

WAIT ZONE

Soak step starts from this

Process Value(PV) points

Target Setting Value(SV)

WAIT TIME

: Wait time... This means the maximum waiting period to start next step when

PV(Process Value) does not reach to the SV(Setting Value).

RAMP STEP SOAK STEP

WAIT ZONE

Soak step starts from this

Process Value(PV) point.

Target Setting Value(SV)

WAIT TIME

4.4 PV/SV start

PV start1．．． Operation will start from the Ramp step including the PV at the starting time of Program operation.

In case more than one step applied, it starts the one with smaller step number.

At these area, operation will not start.

Start operation from this point.

step 1 step2 step3 step4

PV start2．．．The operation is started with the PV (Process Value) at the start of operation as the start temperature.

Start operation from this point.

step 1 step2 step3 step4

SV start．．．Program operation starts from the SV start temperature setting " ".

Start operation from this point.

step 1 step2 step3 step4

4.5 Time Signal Output

It is a function to output at any time at the start of operation or at the transition to the next step.

ON Time

Time Signal

Output

OFF Time

OFF

Start of Step

4.6 Run Signal Output

It is a function to turn on the output during the operation mode or pause mode.

In reset mode, the output is turned off.

Reset Mode

Run Signal

Output

Reset ModeOperation Mode / Pause Mode

OFF Start Operation Stop Operation

4.7 External Operation Function

-It is a function to switch between reset mode and operation mode by external input (DI).

-When "External operation selection setting" is "ON", the function is enabled.

-When the external input is open, the reset mode is set, and when the external input is closed, the operation mode is set.

4.8 Timer operation function

-It is a function to count the time without controlling in step 1. After "Step 1 Time" has elapsed, shift to the next step and

start control.

-The function is enabled when all of the following conditions ①to ③are met.

①Set "SV / PV start selection setting" to "PV start 1" or "PV start 2"

②Set "Step 1 temperature setting" to " (lower limit -1)"

③Set "Step 1 hour setting" to "1 minute" or more

5. Before Program Operation

You can select the input type. Thermocouple(K, J, R, T, N, S, B) and RTD(Pt100) are provided for

this product.

In this Instruction Manual, the following symbol is used in order to use this equipment safely.

Before using this equipment, be sure to set the input type.

- This equipment can handle PID control. Because the control parameter can be set independently for

low, middle, and high temperature, be sure to set each control temperature range.

The setting by key input is stored even though the power is turned off.

Low Temperature control Zone

Middle Temperature control Zone

High Temperature control Zone

1 2 3 4 5 6 7 8 step

→

Caution

6. Operation Flow and Parameter Description

6.1 State transitions between modes

Operation keys will be used to switch between modes.

Common parameter

setting mode

Reset mode

Alarm temperature

setting mode

Operation mode

Pause mode

Control setting mode

Step feed

will be valid only during operation.

Pattern number setting

mode

(All indicators can be

set to go on.)

*Operation: See 6.2 ④.

PATT./STEP for 3

seconds (operations

common to reset mode

and operation mode)

Programming mode

△+ PATT./STEP

for 5 seconds (*1)

RUN/RESET

for 5 sec.

RUN/RESET

for 3 sec.

△+ PATT./STEP

for 3 sec. (*1)

RUN/

RESET

RUN/RESET for 2 sec.

PATT./STEP for 3 sec.

▽for 3 sec.

▽+ PATT./STEP

for 3 sec. (*1)

RUN/RESET

for 2 sec.

△+ PATT./STEP (*1)

RUN/RESET

△+ PATT./STEP

for 3 sec. (*1)

RUN/RESET

▽+ PATT./STEP

for 3 sec. (*1)

RUN/RESET

PATT./STEP

RUN/RESET

▽for 3 sec.

RUN/RESET

△+ ▽

RUN/RESET

▽for 3 sec.

RUN/RESET

*1: Pressing △or ▽first, then press

the PATT./STEP key.

Inhaltsverzeichnis

Andere Toho Electronics Controller Handbücher

Toho Electronics

Toho Electronics TTM-00BW Bedienungsanleitung

Toho Electronics

Toho Electronics TTM-200 Series Gebrauchs- und Pflegehandbuch

Toho Electronics

Toho Electronics TTM-300 Series Bedienungsanleitung

Toho Electronics

Toho Electronics TTX-800 Bedienungsanleitung

Toho Electronics

Toho Electronics TTM-339 Bedienungsanleitung

Toho Electronics

Toho Electronics TTM-1525 Bedienungsanleitung

Toho Electronics

Toho Electronics TRV1-C015 Bedienungsanleitung

Toho Electronics

Toho Electronics TTM-210 Series Gebrauchs- und Pflegehandbuch

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung