Toledo 325 Bedienungsanleitung
OLEDO"
OPERATING INSTRUCTIONS
MODEL
325
PRINTER
REVIEW SCALE OPERATING MANUAL BEFORE OPERATING PRINTER
10
OPERATION
2 5 Remove the l~nertake up cllp and the spent llner
1 1 YOUR TOLEDO MODEL325 PRINTER OPERATES from the take up spool
ON 120 VAC (+lo%-15%) PROVIDED THROUGH 2
6
Place a new roll of labels on the hub,strlp off 4-5
YOUR TOLEDO MODEL SCALE labels before thread~ngthe I~ner,and then thread
per F~gure2
UNDER NO CIRCUMSTANCES SHOULD POWER BE
APPLIED DIRECTLY TOTHE PRINTER. 'WHEN APPLYING
POWER TO YOUR TOLEDO MODEL SCALE, OBSERVE
THE FOLLOWING.
WARNING:
FOR CONTINUED PROTECTION AGAINST
SHOCK HAZARD,CONNECT TO PROPERLY GROUNDED
OUTLET ONLY.
2.7 Insertthe linertake up clip into the take upspool.
2.8 Loker the printhead assembly and replace the
front cover. Close the right side cover and return
thepowerswitchto the"ON" position.Repiacethe
rear cover.
2.9 Press the label advance button on the front of the
printer to advance the label stock untila label can
1.2 Your Toledo Model325 printer is equipped with two
(2)lights (LED's)on the front panel.As youface the
printerfromthe labeldelivery end,the LED'sindicate
the following.
DO NOT REMOVE THE GROUND PRONG
1.2.1 The left LED when lighted indicates: POWER
ON.
be removed.
1.2.2 The right LED when lighted indicates: LOW
LABEL STOCK OR AN ERROR CONDITION.
2.10 Remove the label and continue normal operation
1.3 Printing and Label Delivery
1.3.1 To generate a label for a specific customer
transaction, refer to your scale operator
manual.
2.0
LOADING LABEL STOCK
3.0
CARE AND MAINTENANCE
DO
NOTSPRAY
OR
WASHDOWN.
HAZARD
OF
1
ELECTRICAL SHOCK OR BURN.
i
3.1
TURN OFF
power to the printer. Power is turned
off by switching the "ON/OFFnswitch on the rear
of the printerto th~"OFF" position.
3.2 Use only a clean damp cloth to wipe the exterior
surfaces. Solvents and chemicals may harm the
surface of your Model 325 printer.
4.0
CLEARING A LABELJAM (Under Printhead)
DO NOT USE A METAL OBJECT TO REMOVE ANY
JAMMED LABELS.
4.1 Remove rear cover and turn OFF the printer.
WARNING:
TURN OFF POWERTOTHE PRINTER BEFORE
CLEANING OR LOADING LABELS. POWER IS TURNED 4.2 Remove the front cover to expose the printhead
OFF BY SWITCHING THE "ON/OFF" SWITCH ON THE
/
assembly.
REAR SIDE OF THE PRINTER TO THE "OFF" POSITION.
1
4.3 Remove the label guide with the jammed label
I
2.1 Open the right side cover (as you face the label attached. (See Figure 2)
delivery end) to expose the print deck and label 4.4 Clean any adhesive or debris buildup.
SUPP~Y. 4.5 Replace the label guide and front cover and turn
2.2 Remove the front cover to expose the printhead the printer ON. Replace the rear cover.
assembiy.
2.3 Pull printhead locking lever forward to raise print-
head assembly (see Figure 1).
2.4 Remove the spent paper core.
RAISING
PRINTHEAD
REMOVING
FRONT DOOR
Figure
1
LABEL THREADING DIAGRAM
PRINTHEAD LOCKING BAR
,
LABEL SUPPLY ROLL
PRINTHEAD LABEL GAP
LOCKING LEVER
PRINTHEAD
LABEL TAKEN
STRIPPER BAR PLATEN
t
Figure
2
8
CAUTION: DONOTUSEAMETALTOOLOR INSTRUMENT
TO REMOVE JAMMED LABEL AS THIS CAN CAUSE
I
SEVERE DAMAGETO ELECTRONIC PARTS.
CALL
YOLIR
AUTHORIZED TOLEDO
SCALE
REPRESEN-
TATIVE SHOULD DISASSEMBLY OF THE MACHINE BE
REQUIREDTO TOTALLY REMOVEA JAMMED LABEL OR
ITS ADHESIVE RESIDUE.
4.6 Liner Wrap Up On Drive Roller
a) Be sure to TURN OFF Scale.
b) PLACE Release Roller.-Arm to the open
position.
c) REMOVE (tear off) liner ENTERING and
EXITING the Drive Roller.
d) .GRASP the liner exiting the Drive Roller and
pull liner off Roller.
e) RE-INSTALL and RE-THREAD labels per
Section 2.0.
5.0
CLEANING
The printhead and drive mechanism should be cleaned
on a regular basis by the user. Toledo recommends a
cleaning frequency of approximately 100,000 labels
(Reference label counter under right side cover).
5.1 Remove rear cover and TURN OFF printer.
5.2 Remove front cover and pull printhead locking
lever forward to raise printhead assembly.
5.3 Remove label stock liner and label guide.
5.4 Dust the label taken and label gap sensor with a
soft brush (see Figure 2).
5.5 Clean along the black resistor line with cleaner
I.S.C.108, Toledo Scale P/N 125875OOA.
6.0
PRINTER MALFUNCTION
An apparent printer malfunction can be caused
byeitherthescaleorprinter.Refertothescaleoperators
manual to verify proper operation of the scale. Should
the printer fail to deliver a label, check the following:
6.1 Check paper supply for jams or tears
6.2 Check the side-cover and front cover interlock
switches, be sure they close properly.
6.3 Cyclethe printer bypressingthe labeladvance/test
button on the front of the printer for two (2)
seconds, a test label should be issued.
6.4 Check the printer fuses and Interconnect cables
located under the rear cover
Should the printer continue to malfunction, call your
Authorized Toledo Scale Service Representative.
7.0
MOVINGTHE PRINTER
7.1 TURN OFF power to the scale and printer by
switching the "ON/OFFWswitch located on the
scale to the "OFF" position and the "ON/OFF"
sw~tchonthe printertothe "OFF" position. Remove
the scale power cord from the A-C outlet.
7.2 Refer to your scale manual for instructions
on moving the scale and 325 printer.
CAUTION: 'This equipmentgeneratesand usesradiofrequen-
cyenergy and if not installed and used properly, i.e., instrict
accordance with the instructionmanual, maycause harmful
interference to the limits for a Class A computing device
pursuant to Subpart J of Part 15 of FCC Rules, which are
designed to provide reasonable protection against such
interference when operated in a commercial environment.
Operation of this equipment in a residential area is likely to
cause interference inwhichcasethe userat hisownexpense
will be required to take whatever meesures that may be
required to correct the interference.
8.0
CLEANING FLUIDS
DO NOTSCRAPE OR CLEAN THETHERMAL PRINTHEAD Clean the Printhead with cleaner I.S.C. 108, Toledo
WITH ANY OTHER OBJECT AS PRINTER WARRANTY Scale P/N 125875OOA.
1
WILL BE AFFECTED.
I
L--
1
WARNING: WHEN CLEANING 'THE MODEL 325 ALL FOOD
5.6 Clean any built-up adhesive or debris from the
I
PRODUCTS AND PACKAGING MATERIALS MUST BE
platen.
I
1
CAREFULLY REMOVEDFROMTHEAREA OR CAREFULLY
1
5.7
Replace label gu~deand reload label stock PROTECTED. ALL ODORS ASSOCIATED WlTH THESOL-
I
VENTS MUSTBEDISSIPATEDBEFOREFOODPRODUCTS
1
5.8 Lowerprintheadassembly, replacecoverandreturn OR PACKAGING MATERIALS ARE RE-EXPOSED IN THE
1
the power switch tothe
ON
position. Replacerear AREA.
1
cover. PLEASE SAVETHESE INSTRUCTICNS
FOR FUTURE REFERENCE
Toledo Scale
/
Worthington, OH 43085
/
1-800-447-9206
/
In Ohio call 614-438-4594
TOLEDO SCALE
r
RELIANCE ELECTRIC
Printed in
U.S.A.
P/N
127980 OOA
