TONGHER TH-Mars 2 Bedienungsanleitung

ELECTIRC FENCE

ENERGIZER

INSTALLATION AND USER MANUAL

（TH-Mars 2 / ES2，TH-Mars 5 / ES5）

Thank you for purchasing this Energizer

INSTALLATION AND USER MANUAL

- 1 -

WARNING

Please read all instructions before using the Energizer

DO NOT connect the fence to any other electric device.

• Lightning may strike your fence. A severe electric shock hazard exists to anything connected

to the fence or in near proximity to the grounding system.

• If connecting Energizer to AC power source, only use the provided AC adapter. The Energizer

connected to AC power shall be covered adequately to protect it from rain, snow or other moisture.

Keep out of reach of children.

• DO NOT Charge the battery with a battery charger while the Energizer is connected.

Disconnect and remove battery if re-charging is necessary.

• DO NOT connect more than one Energizer to the fence at one time.

• DO NOT connect two fences to the same Energizer.

• Keep fence at least 2 yards away from other fences with metal posts.

• DO NOT connect Energizer to barbed wire or razor wire.

• DO NOT install fence or grounding system within 10 yards of electrical power lines,

telephone lines, or telecommunications equipment.

• If running leads underground, use insulated wire and conduit rated for a minimum of 12,000 volts.

Prevent water from entering conduit.

• Keep young children away from the electric fence at all times.

• DO NOT touch the fence with head, neck or torso.

• DO NOT climb over, through or under a multi-wire electric fence. Use a gate or disconnect

the fence wires to cross.

• DO NOT put electric fence in areas of public access.

• Clearly mark the electric fence in several locations if located where people unfamiliar with the

fence may come into its proximity. Check your local and state laws regarding placement of electric

fences.

• Keep fence clear of obstructions or other objects that could potentially cause a person or

animal to become entangled in the fence.

• DO NOT use a water pipe, well, or your main power system ground as the ground for your

Energizer. If lightning were to strike the fence, the current could travel through the system causing a

severe electrical shock hazard.

• Place the grounding rod in a location that will not cause a person or animal to trip into fence or be

trapped between the ground wire and the fence.

• Always mount the Energizer securely such that it will not fall if bumped by an animal or person.

• Disconnect Energizer if conditions are extremely dry and represent high risk of fire.

• Keep combustible materials away from fence, Energizer and battery.

INSTALLATION AND USER MANUAL

- 2 -

Contents

1. About the electric fence energizer ---------------------------------------------------------------------------1

How does an electric fencing system work?

2. TH-Mars 2 Mars 5

2.1. Main features ---------------------------------------------------------------------------------------------2

2.2. Parts of the energizer------------------------------------------------------------------------------------3

2.3. Operation mode------------------------------------------------------------------------------------------4

2.4. Timer--------------------------------------------------------------------------------------------------------4

3. TH-Mars ES2 Mars ES5-------------------------------------------------------------------------------------------5

3.1. Main features---------------------------------------------------------------------------------------------5

3.2. Indication and setting-----------------------------------------------------------------------------------5

4. Installing the Electric Fence Energizer -----------------------------------------------------------------------6

4.1 Connecting to the power source ---------------------------------------------------------------------6

-mains power

-battery

-solar/battery

4.2 Install the energizer-------------------------------------------------------------------------------------8

4.3 Install the earthing system----------------------------------------------------------------------------10

4.4 Lead-out from the energizer--------------------------------------------------------------------------13

4.5 Post and wire spacings---------------------------------------------------------------------------------14

4.6 warning sign----------------------------------------------------------------------------------------------14

4.7 Safety requirements ------------------------------------------------------------------------------------14

5. Trouble-shooting-------------------------------------------------------------------------------------------------15

6. Maintenance------------------------------------------------------------------------------------------------------17

7. Manufacturer Warranty----------------------------------------------------------------------------------------17

8. Contact information---------------------------------------------------------------------------------------------17

Operator’s Manual

This manual is designed to ensure you achieve optimum results from your Electric Fence Energizer.

To ensure maximum output with minimum complications and optimum safety, we advise you to

follow the guidelines carefully concerning the correct installation of your fence energizer and the

required earthing system. Anything less will substantially affect the performance of the energizer

and can result in unnecessary complications and installation expense.

About the electric fence energizer

This Electric Fence Energizer is a comprehensive perimeter or strip fencing energizer and is an ideal

solution for those who want a simple, efficient and cost-effective system to power their fences.

It is easy to install and can be operated using either AC mains power, 12 volt (v) deep cycle

lead-acid/gel battery or in conjunction with a 30/40/50 or other watt (w) solar panel, making this a

suitable system for larger scale settings where no mains power is available. As a combination, fixed

or portable system, the Electric Fence Energizer provides flexibility with pasture management and is

the ideal solution for short or long-term animal control or rotational crop grazing

How does an electric fencing system work?

An electric current, generated from an energizer

which is earthed, travels along a fence wire as a

pulse. The circuit between the fence and the ground

is completed when an animal touches the fence

wire and consequently receives a short, sharp but

safe shock. This provides enough of a deterrent to

an animal, making the electric fence a psychological

barrier rather than a physical one.

TH-MARS SERIES PRODUCT SPECIFICATIONS

TH-MARS 2

TH-MARS ES2

TH-MARS 5

TH-MARS ES5

TH-MARS 6

Power supply 12V（110-240V 50HZ/60HZ）

Interval Period 1.2 / 2.0 s

1.2 / 2.0 s 1.2 / 2.0 s

LCD shows working Yes NO Yes NO YES

Consumption using a

power adaptor

1.92W 1.92W 2.4W 2.4W 2.85W

Timer Option NO Option NO Option

Intelligent fault

self-detection

YES YES YES YES YES

Output voltage

adjustment

Yes NO Yes NO Yes

Input current 160mA 160mA 200mA 200mA 220mA

Peak output voltage

（NO LOAD） 10 kV 10 kV 10 kV 10 kV 12 kV

Output voltage（500Ω）

4.5kv 4.5kv 4.5kv 4.5kv 6.0kv

Stored energy 2.9 J 2.9 J 5.4 J 5.4 J 6.3J

Km Multi Wire Fence 25km 25km 35km 35km 39km

Tongher Recommends

8km 8km 10km 10km 12km

INSTALLATION AND USER MANUAL

- 2 -

2. TH-Mars 2 Mars 5

2.1 Main features :

 Powered by: AC mains power or, 12v deep cycle lead-acid/gel battery (not included) 30-60w

solar panel (not included) in conjunction with a 12v battery as above

 6 operating modes including a cost-efficient day/night full/half power save

 2 different pulse intervals of 1.5 seconds and 2.5 seconds

 2 different max output of full and half energy

 LCD shows the energizer working state, voltage , interval time, setting etc.

 LED display the energizer working states, power/on/shock

 Waterproof and dustproof IP44

 Timer（Option）

Performance Characteristics

 output voltage: 7-12 kv

 pulse width: 100 us (1/1000 second)

 Stored energy: 2 / 5 joules

 Consumption(Max):

Mars 2 : 1.92 watt

Mars 5 : 2.4 watt

Package Contents

 1 x Electric Fence Energizer

 1 x Mains power adaptor

 1 x Lead-out cable (red) to connect Energizer to fence

 1 x Earthing cable (green) to connect Energizer to earthing system

 1 x Set of leads to connect Energizer to 12 v deep cycle lead-acid/gel battery option (red and

black clips)

 1 x user manual

 1 x box packaging

INSTALLATION AND USER MANUAL

- 3 -

2.2 Parts of the energizer

Power – Should be blue when properly connected to a 110v outlet or a fully charged 12v

deep cycle battery.

Status – Should be red when the energizer is producing voltage.

If the Status light is not illuminated, then check the energizer.

Shock indication

Flashing indicate the shock from energizer

Sensor – Light sensor for controlling pulse speed on Short Day/Long Night or Long

Day/Short Night operational modes.

INSTALLATION AND USER MANUAL

- 4 -

2.3 operation mode:

The working state can be controlled by these two buttons(UP/DOWN)

Hold-on mode: The Power LED indicator should be blue. Digital display will show

Output Voltage at 0kv and the Input Power Voltage. Status LED indicator should not

be lit. When in the On-Hold mode, the energizer will not generate a pulse.

Full energy mode: Energizer pulse will be every 1.2 seconds. The Power LED

indicator should be blue. Status LED indicator should be red. Digital display will

show Output Voltage at the energizer as well as the Input Power Voltage.

Reduced Energy Mode: Energizer power is reduced by 25%. The energizer pulse will

be every 1.2 seconds. The Power LED indicator should be blue. Status LED indicator

should be red. Digital display will show Output Voltage at the energizer as well as

the Input Power Voltage.

Short-day, long-night mode : Daytime pulse will be every 1.2 seconds, night pulse

will be every 2 seconds. The Power LED indicator should be blue. Status LED

indicator should be red. Digital display will show Output Voltage at the energizer as

well as the Input Power Voltage.

Long-day, short-night mode : Daytime pulse will be every 2 seconds, night pulse will

be every 1.2 seconds The Power LED indicator should be blue. Status LED indicator

should be red. Digital display will show Output Voltage at the energizer as well as

the Input Power Voltage.

Battery Saving Mode: Energizer power is reduced by 25%. The energizer pulse will

be every 2 seconds. The Power LED indicator should be blue. Status LED indicator

should be red. Digital display will show Output Voltage at the energizer as well as

the Input Power Voltage.

When this energizer is plugged into a standard 110v-240v outlet power source, the Power Voltage

display will read close to 12.6v. When the energizer is attached to a 12v deep cycle battery,

the Power Voltage should read between 12.2 and 13.6 volts. If the voltage of the battery reads

lower than 12.2volts that indicates it is time to recharge the battery.

2.4 Timer

There is extra function for some customer – timer

This timer is base on weekly , we can set the timer using the buttons “UP” “DOWN”.

1. Timer without setting : None stop working

2. Start and stop in the same day but different time, means repeat daily working

3. Start and stop in different day , means repeat weekly working

(More setting operation please refer to our technology support and Reseller)

Setting

1. Push “UP” to Hold-on mode

2. Push “DOWN” 5 Seconds,and enter setting interface.

3. Push “UP” to modify the value, and DOWN to move to next setting bit.

4. “Y” submit the setting ,”N” cancel the setting

Top two rows is the current time

INSTALLATION AND USER MANUAL

- 5 -

TH-Mars ES2 and TH-Mars ES5

3.1 Main features:

 Powered by: AC mains power or, 12 v deep cycle lead-acid/gel battery (not included) 30-60 w

solar panel (not included) in conjunction with a 12 v battery as above

 5 operating modes

 2 different pulse intervals of 1.5 seconds and 2.5 seconds

 2 different max output of full and half energy

 LED display the energizer working states, power/on/shock

 Waterproof and dustproof

Performance Characteristics

 output voltage: 7-10 kv

 pulse width: 100 us(1/1000 second)

 Output energy: 2 / 5 joules

 Consumption(Max):

Mars ES 2 : 1.92 watt

Mars ES 5 : 2.4 watt

3.2 Indication and setting

 Power light/state (Green)

Power supply is connected from mains power or battery

On: power input is good

1 Hz flash : power is low , energizer will be deactivated

E1 inner error

0.5 Hz flash: E2 inner error

working states(Red) :output energy

On: full power output

Flash : half power output

 working states(Red) : interval time

On: 2 second

Flash : 1 second

Change the working state by pushing “UP” and “DOWN”

INSTALLATION AND USER MANUAL

- 6 -

3. Installing the Electric Fence Energizer

4.1 Connecting to the power source

The Electric Fence Energizer can operate using mains power, 12 v deep cycle lead-acid/gel battery

or solar and lead-acid/gel battery.

Mains power

1. Attach the mains power adaptor to the Energizer

– insertion point on reverse side of unit – and

plug into the mains power socket

2. DO NOT turn the mains power on until the

powered fence system is fully constructed and

you are ready to use it

Battery (not included)

1. Always use a 12 v deep cycle lead-acid/gel battery

2. Site the battery in a well-ventilated area

3. Attach the battery cable to the Energizer – insertion

point on the reverse of the unit

4. Connect the RED clip to the POSITIVE (+) terminal of

the external battery

5. Connect the BLACK clip to the NEGATIVE (-)

terminal of the external battery

Battery: Lead-acid or other kind of battery with voltage

more than 12 v.

Solar/battery (not included)

1. The Electric Fence Energizer is compatible

with a minimum 40 w solar fence panel and a

12 v deep cycle lead-acid/gel battery

2. Set up the solar panel as per the instructions

enclosed with it using the appropriate

regulator. If you bought your solar panel it

will include the correct charging regulator.

3. Set up the 12 v deep cycle lead-acid/gel

battery as per above instructions for Battery

Solar panel: voltage more than 12 v solar controller or

battery is necessary)

INSTALLATION AND USER MANUAL

- 7 -

The best place to site the Electric Fence Energizer depends upon which of the three power supplies

you choose; mains power, battery or solar/battery. See table 1

Power supply Benefits Energizer best positioned

Mains power  Cost-effective

 Reliable

 Mount out of reach of children & animals

 Position near to a power point either inside or

outdoors

 Avoid long lead-outs running adjacent to power or

telecommunications cables or other earthing systems

 Site at least 10 metres (m) away from any other

electric or telecommunications cables or earth systems

 If possible, site the Energizer in the middle of the

fencing system

Battery  Practical choice in

areas of inaccessible

mains power

 Electric Fence

Energizer can be fitted

with a 12 v deep cycle

lead-acid/gel battery*

(80 Ah is

recommended)

 Mount out of reach of children & animals

 Position near a power point if using combination

mains power/battery and follow guidelines as for mains

power

 Keep Energizer off the ground if siting outside to

protect electrical components from insect and moisture

damage

 If necessary, build a protective box/fence around the

Energizer

 If possible, site the Energizer in the middle of the

fencing system

Solar  Logical choice for

remote areas where no

mains power available

 For the Electric Fence

Energizer a 12-volt

deep cycle

lead-acid/gel

battery

(50-80 Ah is

recommended) plus a

30-50 w solar

panel(depend on the

sunlight intensity )

 Mount out of reach of children & animals

 Keep Energizer off the ground to protect electrical

components from insect, livestock and moisture damage

 If necessary, build a protective box/fence around the

Energizer

 If possible, site the Energizer & solar panel in the

middle of the fencing system

 Position the solar panel to face north in the southern

hemisphere and south in the northern hemisphere.

Protect from possible damage by livestock

 Some adjustment of the panel may be required to

accommodate the midday, winter sun

Table : Siting the energizer depending on the choice of power supply

Important: If using a rechargeable battery, choose one that withstands regular, charge and

discharge cycles without damage, such as a marine or deep cycle type. Do not use automotive

batteries because they supply high current for short periods and may not provide the continual

output you require.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere TONGHER Stromversorgung Handbücher

TONGHER

TONGHER TH-TE05 Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung