Topcom TwinWalker 5000 Bedienungsanleitung

USER MANUAL

HANDLEIDING

GEBRAUCHSANWEISUNG

MANUEL D’UTILISATEUR

BRUKSANVISNING

BRUGERMANUAL

KÄYTTÖOHJE

HL_TT5000.book Page 1 Tuesday, May 13, 2003 10:18 AM

This product is in compliance with the essential requirements and other relevant provisions of the R&TTE directive 1999/5/EC.

The Declaration of conformity can be found on :

http://www.topcom.net/support/declarations/

HL_TT5000.book Page 2 Tuesday, May 13, 2003 10:18 AM

Topcom Twintalker 5000 3

ENGLISH

1. DESCRIPTION 4

2. INSTALLATION 4

2.1. Removing/Installing the Belt Clip 4

2.2. Battery Installation 4

3. LCD SCREEN 5

4.GETTING STARTED 5

4.1. Turning the Unit ON/OFF 5

4.2. Adjusting Speaker Volume 5

4.3. Receiving a Signal 5

4.4. Transmitting a Signal 5

5. OPERATION 6

5.1. Changing Channels 6

5.2. CTCSS (Continuous Tone Coded Squelch System) 6

5.3. Monitor 6

5.4. Menu Lock 7

5.5. VOX Selection 7

5.6. Channel Scan 7

5.7. Battery Charge Level/Low Battery Indication 7

5.8. Using rechargeable batteries 8

5.9. Headset use 8

5.10. Sending Call Tones 8

6. SPECIFICATIONS 8

7. SAFETY INSTRUCTIONS 9

7.1. Damage antenna 9

7.2. Batteries 9

7.3. For vehicles with air bag 9

7.4. Potentially Explosive Atmospheres 9

7.5. Blasting caps and areas 9

7.6. Electromagnetic Interference/Compatibility 10

8. CARE AND MAINTENANCE 10

9. WARRANTY 11

HL_TT5000.book Page 3 Tuesday, May 13, 2003 10:18 AM

4 Topcom Twintalker 5000

ENGLISH

1. DESCRIPTION

1. Antenna

2. Talk Button

3. Call Button

4. Flash light button

5. Charger Jack

6. Microphone

7. Speaker

8. Navigator button

9. Earphone Jack

10. Menu button

11. LCD screen

12. On/Off button

13. Flashlight

2. INSTALLATION

2.1. Removing/Installing the Belt Clip

1. To remove the clip from the unit, push up on the belt clip while pulling the clip tab.

2. When re-installing the belt clip, a click indicates the BeltClip is locked into position.

2.2. Battery Installation

1. Remove the belt clip.

2. Push the battery cover and slide it away from the antenna

3. Install four ‘AAA’ alkaline or rechargeable batteries following the polarity as shown.

4. Re-install the Battery Cover and Belt Clip

13 12

HL_TT5000.book Page 4 Tuesday, May 13, 2003 10:18 AM

Topcom Twintalker 5000 5

ENGLISH

3. LCD SCREEN

ARX icon. Displayed when receiving a signal.

BTX icon. Displayed when transmitting a signal.

CSpeaker volume level

DMenu lock symbol

EBattery level

FDisplayed during VOX mode.

GDisplayed during CHANNEL SCAN mode.

HChannel number (1-8)

ICTCSS code (1-38)

4.GETTING STARTED

4.1.Turning the Unit ON/OFF

To activate; press and hold the POWER button . The unit will “beep” and the LCD

Screen will display the current channel.

To switch off; press and hold the POWER button again. The unit will “beep” and the

LCD Screen will turn blank.

4.2. Adjusting Speaker Volume

TheSpeakerVolume can beadjustedbypushing thenavigatorupor down.TheSpeaker

Volume level is displayed on the LCD.

4.3. Receiving a Signal

The unit is continuously in the RECEIVE mode when the unit is ON and not transmitting.

When you receive a signal on the current channel, the RX icon is displayed

4.4.Transmitting a Signal

1. Press and hold the TALK button to TRANSMIT.

2. Hold the unit in a vertical position with the MICROPHONE 5 cm from the mouth and

speak into the microphone.

3. Release the TALK button when you have finished talking.

IMPORTANT: In order for other people to receive your transmission, they

must also be on the same channel and have set the CTCSS code you are

currently using. Refer to the ‘Changing Channels’

VOX

SCAN

HL_TT5000.book Page 5 Tuesday, May 13, 2003 10:18 AM

6 Topcom Twintalker 5000

ENGLISH

5. OPERATION

5.1. Changing Channels

The PMR has 8 available channels.

To change channels:

1. Press the MENU button once, the current channel number flashes on the

LCD Screen.

2. Push the navigator up or down to change the channel.

3. Press the MENU button to confirm the channel selection and go to CTCSS

SUB-CHANNEL SELECTION mode, or press the TALK button to select the desired

channel and return to NORMAL mode.

5.2. CTCSS (Continuous Tone Coded Squelch System)

The 2 digit CTCSS code corresponds to a specific tone frequency the radio emits. Two

users, with the same channel and CTCSS set can hear one another.They will

not

able to hear anyone else on the channel unless the other radios have the same exact

CTCSS code enabled.

The Twintalker 5000 has 38 CTCSS codes available.

1. Press the MENU button twice, the CTCSS code will flash

2. Push the Navigator up or down to change the CTCSS code.

3. Press the TALK button to confirm your selection and return to the NORMAL mode.

4. To confirm and shift to the next option, press the MENU button.

NOTE: Set the CTCSS code to“0” to disable the CTCSS function.

NOTE: Any PMR set on the same channel can receive and listen to the

conversation, also when the other use a CTCSS code.

5.3. Monitor

You can use the MONITOR feature to check for weaker signals in the current channel.

•Press the Navigator button to the right for normal monitoring .

•Press and hold the Navigator button to the right.After 3 seconds you can release

the button.You are now continuous monitoring the channel until you push theTALK

button.

HL_TT5000.book Page 6 Tuesday, May 13, 2003 10:18 AM

Topcom Twintalker 5000 7

ENGLISH

5.4. Menu Lock

Press and hold the Navigator button to the left. The menu lock symbol will appear on the

display.PressandholdtheNavigatorbuttonagaintotheleftuntilthesymboldisappears.

When the menu lock is on, you can not change the settings like volume, channel, etc ...

5.5.VOX Selection

The PMR is capable of voice activated (VOX) transmission. In VOX mode, the radio will

transmit a signal when it is activated by your voice or other sound around you. VOX

operation is not recommended If you plan to use your radio in a noisy or windy

environment.

1. Press the MENU button 3 times.

2. Press the navigator button UP to turn the VOX feature ON. Press the navigator up

toselecttheVOXsensitivity level which isindicatedintherightcorner of the display.

Press the navigator button DOWN until OF appears on the display, to turn VOX

OFF.

3. In the VOX mode, the VOX icon will be displayed.

4. To confirm your selection and return to the NORMAL mode, press the TALK button.

5.6. Channel Scan

CHANNEL SCAN performs searches for active signals in an endless loop from channel

1 to 8.

1. Press the navigator button UP. At the same time, press the MENU button briefly

to start scanning.

2. Release the Navigator button.

3. When an active signal (one of 8 channels) is detected, CHANNEL SCAN pauses

and you will hear the active signal.

4. PresstheTALKbuttontocommunicatethroughthe active signal channel. Press the

MENU button to deactivate SCAN.

5. When an active signal (one of 8 channels) is detected, press the navigator button

UP or DOWN button to bypass the current channel and continue to search for

another active channel

5.7. Battery Charge Level/Low Battery Indication

•The BATTERY CHARGE LEVEL is indicated by the number of squares present

inside the BATTERY icon on the LCD Screen.

•When the BATTERY CHARGE LEVEL is low, the BATTERY icon will ﬂash to indi-

cate that the batteries need to be replaced or recharged.

HL_TT5000.book Page 7 Tuesday, May 13, 2003 10:18 AM

8 Topcom Twintalker 5000

ENGLISH

5.8. Using rechargeable batteries

Important: Do not charge this unit using an AC/DC ADAPTER with regular

“AAA”alkaline batteries installed. Only use the optional AC/DC ADAPTER

with“AAA”rechargeable batteries (not included).

To use the PMR with an AC/DC ADAPTER and rechargeable batteries do the following:

1. Insert four (4) “AAA” rechargeable batteries (not included).

2. Plug the 12 V DC / 100 mA ADAPTER (not included) into the CHARGER JACK at

side of the unit and turn it ON by pressing the POWER button.

NOTE:The unit cannot transmit while the batteries are being charged. It

takes approximately 8 to 10 hours to fully charge the batteries.

5.9. Headset use

You can operate the PMR using a headset (not included).Plug the headset into the EAR/

MIC jack

5.10. Sending Call Tones

You can use Call Tones to alert the other user to identify yourself. You can also use Call

Tones to signal the beginning or the end of a transmission.

1. Press and release the CALL button. The CALL TONE continues for 3 seconds.

2. Your CALL TONES will transmit to nearby receivers set to the same channel.

5.11. Flashlight

Press and hold the Flashlight button to activate the light.

6. SPECIFICATIONS

Channels

CTCSS Sub-channel

Output Power (TX)

Range

Charging adaptor

8 Channels

38 for each Channel

Output Power: 0.5W (Maximum)

Up to 3 Km (open field)

12 V DC / 100 m A

HL_TT5000.book Page 8 Tuesday, May 13, 2003 10:18 AM

Topcom Twintalker 5000 9

ENGLISH

7. SAFETY INSTRUCTIONS

7.1. Damage antenna

Do not use any communicator that has a damaged Antenna. If a damaged antenna

comes in contact with the skin, a minor burn may result.

7.2. Batteries

As batteries can cause property damage and/or bodily injury such as burns if conductive

material such as jewelry, keys or beaded chains touches exposed terminals. The

material may complete an electrical circuit (short circuit) and become quite hot. Exercise

care in handling any charged battery, particularly when placing it inside a pocket, purse

or other container with metal objects.Do not replace or charge batteries in a potentially

explosiveatmosphere.Contactsparking mayoccurwhileinstalling orremovingbatteries

and cause an explosion.

7.3. For vehicles with air bag

Do not place your Communicator in the area over an air bag or in the air bad deployment

area. Air bags inflate with great force. If a communicator is placed in the bag deployment

area and the air bag inflates, the communicator may be propelled with great force and

cause serious injury to the occupants of vehicle.

7.4. Potentially Explosive Atmospheres

Turn your communicator off when in any area with a potentially explosive atmosphere,

unless it is a type specifically qualified for such use. Sparks in such areas could cause

an explosion or fire resulting in bodily injury or even death.

7.5. Blasting caps and areas

To avoid possible interference with blasting operation, turn your communicator off near

electrical blasting caps or in a ‘blasting area’ or in areas posted : ‘Turn off two way radio’.

Obey all signs and instructions.

Note : Areas with potentially explosive atmospheres are often, but not

always, clearly marked.They include fueling areas such as below deck on

boats, fuel or chemical transfer or storage facilities; areas where the air

contains chemicals or particles, such as grain, dust or metal powders; and

any other area where you would normally be advised to turn off your vehicle

engine.

HL_TT5000.book Page 9 Tuesday, May 13, 2003 10:18 AM

10 Topcom Twintalker 5000

ENGLISH

7.6. Electromagnetic Interference/Compatibility

Nearly every electronic device is susceptible to electromagnetic interference (EMI) if

inadequately shielded, designed or otherwise configured for electromagnetic

compatibility.

Turn your unit OFF in any facilities where posted notices instruct you to do so. Hospitals

or health care facilities may be using equipment that is sensitive to external RF energy.

Turn your unit OFF when on board an aircraft when instructed to do so. Any use of the

unit must be accordance with airline regulations or crew instructions.

8. CARE AND MAINTENANCE

To clean the unit, wipe with a soft cloth dampened with water. Don’t use a cleaner or

solvents on the unit; they can harm the case and leak inside, causing permanent

damage. Battery contacts may be wiped with a dry lint-free cloth. If the unit gets wet, turn

it off and remove the batteries immediately. Dry the BATTERY COMPARTMENT with a

solf cloth to minimize potential water damage. Leave the cover off the BATTERY

COMPARTMENT overnight or until completely dry. Do not use the unit until completely

dry.

HL_TT5000.book Page 10 Tuesday, May 13, 2003 10:18 AM

Inhaltsverzeichnis

Sprachen:

Andere Topcom Zwei-Wege-Funkgerät Handbücher

Topcom

Topcom Twintalker 9000 Bedienungsanleitung

Topcom

Topcom KS-4216 Bedienungsanleitung

Topcom

Topcom Protalker PRT-1078 Bedienungsanleitung

Topcom

Topcom Twintalker 6800 Bedienungsanleitung

Topcom

Topcom Twintalker 9500 Airsoft Edition Bedienungsanleitung

Topcom

Topcom TWIN TALKER 3500 Bedienungsanleitung

Topcom

Topcom Twintalker RC-6410 Bedienungsanleitung

Topcom

Topcom RC-6412 Bedienungsanleitung

Topcom

Topcom KS-4222 Bedienungsanleitung

Topcom

Topcom Twintalker 9100 Bedienungsanleitung

Topcom

Topcom TwinTalker 6000 Bedienungsanleitung

Topcom

Topcom Twintalker 1302 Bedienungsanleitung

Topcom

Topcom TWINTALKER RC-6404 LONG RANGE Bedienungsanleitung

Topcom

Topcom Twintalker 9100 Bedienungsanleitung

Topcom

Topcom Twintalker 3700 DUO PACK Bedienungsanleitung

Topcom

Topcom Twintalker 9500 Airsoft Edition Bedienungsanleitung

Topcom

Topcom Multitalker 1000 Bedienungsanleitung

Topcom

Topcom Twintalker 6800 Bedienungsanleitung

Topcom

Topcom RC-6400 Bedienungsanleitung

Topcom

Topcom Twin Talker 3800 Bedienungsanleitung

Topcom

Topcom TwinTalker 3700 Bedienungsanleitung

Topcom

Topcom Twintalker 1300 Mega Mindy Merkblatt

Topcom

Topcom Twintalker 5010 Bedienungsanleitung

Topcom

Topcom TWINTALKER RC-6401 Bedienungsanleitung

Beliebte Zwei-Wege-Funkgerät Handbücher anderer Marken

Midland

Midland 70-1526A/B Bedienungsanleitung

HYT

HYT TC700 Bedienungsanleitung

DNT

DNT Space100 Bedienungsanleitung

Legacy

Legacy ProLine Series Bedienungsanleitung

Evolveo

Evolveo FreeTalk XM2-2 Bedienungsanleitung

AWC

AWC AWR1688+ Bedienungsanleitung

Motorola

Motorola XT665d Bedienungsanleitung

Cobra

Cobra 2-Way Radio Bedienungsanleitung

Klutch

Klutch KR-400 Bedienungsanleitung

Garmin

Garmin Rino 655t Bedienungsanleitung

Motorola

Motorola TLK 150 Bedienungsanleitung

Midland

Midland MXT275J Bedienungsanleitung

Titan

Titan TR200 Bedienungsanleitung

Cobra

Cobra CXT645 Bedienungsanleitung

Tait

Tait TM9100 Bedienungsanleitung

Yaesu

Yaesu FT-65R Bedienungsanleitung

Motorola

Motorola ASTRO SRX 2200 Series Bedienungsanleitung

Motorola

Motorola T5583 Bedienungsanleitung