TOPMAQ MS70 Technisches Handbuch
OPERATION INSTRUCTION
Push Sweeper / MS70
Table of contents
1. Safety information
2. Layout
3. Items supplied
4. Intended use
5. Technical date
6. Assembly
7. Operation
8. Adjusting the feed-in brushes
9. Emptying the debris collector
10. Height adjustment and folding of the push bar
11. Ordering spare parts
12. Disposal and recycling
Important
When using the equipment, a few safety precautions must be observed to avoid injuries
and damage.
Please read the complete operating instructions and safety information with due care.
Keep this manual in a safe place so that the information is available at all times. If you give
the equipment to any other person, hand over these operating instructions and the safety
information as well. We cannot accept any liability for damage or accidents which arise
due to a failure to follow these instructions and the safety information.
1. Safety information
Please refer to the booklet included in delivery for the safety information.
CAUTION
Read all the safety regulations and instructions.
Any errors made in following the safety information and instructions set out below may
result in an electric shock, fire and/or serous injury.
Keep all safety regulations and instructions in a safe place for future use.
Take suitable measures to keep the equipment out of the reach of children.
Immediately replace defective parts.
Use only original replacement parts.
We will not be liable for any damage that results from improper repairs and/or
improper handing of the unit (e.g. Using the unit in ways for which it was not
intended).
The sweeping up of gel-like, liquid, combustible or explosive substances is not
permitted.
Do not use the mechanical sweeper to sweep up glowing or harmful objects.
2. Layout (Fig. 1)
1. Push bar
2. Adjustment nut for push bar
3. Fastening nuts for push bar
4. Feed-in brush
5. Setting screw for adjusting the height of the feed-in brushes
6. Debris collector
3. Items supplied (Fig. 2)
Open the packaging and take out the equipment with care.
Remove the packaging material and any packaging and/or transportation braces (if
available).
Check to see if all items are supplied.
Inspect the equipment and accessories for transport damage.
If possible, please keep the packaging until the end of the guarantee period.
IMPORTANT
The equipment and packaging material are not toys. Do not let children play with
plastic bags, foils or small parts. There is a danger of swallowing or suffocating!
Item Description
1 Push bar top section
2 Push bar bottom
3 Mechanical sweeper with removable debris collector
4a Push bar mount left
4b Push bar mount right
5 Adjustment nut (4 pieces)
6 Fixing screw for push bar extension (2 pieces)
7 Assembly screw for push bar (2 pieces)
8 Feed-in brush ( 2 pieces)
9 Fixing screw for feed-in brushes (6 pieces)
4. Intended use
The mechanical sweeper is intended for sweeping level and dry areas such as entrance
drives, terraces, yards, etc.
The equipment may only be used for the tasks it is designed to handle. Any other use is
deemed to be a case of misuse. The user/operator and not the manufacturer will be liable
for any damage or injuries of any kind caused as a result of this.
Please note that our equipment has not been designed for use in commercial, trade or
industrial applications. Our warranty will be voided if the equipment is used in commercial,
trade or industrial business or for equivalent purpose.
5. Technical date
Working width 70cm
Debris collector 14l
Sweeping capacity (at 4km/h) max. 2800m3/h
Size 650x600x210mm
Weight 8.9kg
6. Assembly ( Fig. 2-5)
Note: you will find the feed-in brushes and the assembly material in the debris collector.
1. The feed-in brushes (8) are fastened to the locating plates with 3 screws (9) each.
2. Insert the push bar mounts (4a/4b) into the receiving slots.
3. Secure the push bar mounts (4a/4b) with the screws (6)
4. Push the bottom section of the push bar (2) onto the push bar mounts (4a/4b) and
secure with the two adjustment nuts (5).
5. Slide the top section of the push bar (1) onto the bottom section of the push bar (2)
and secure with two assembly screws (7) and two adjustment nuts (5).
7. Operation ( Fig. 7)
When the mechanical sweeper is pushed, the feed-in brushes (B) and the pick-up brushes
(C) are set in rotation by the belt drives (A). The rotating feed-in brushes (B) sweep the dirt
to the center. The two counter-rotating pick-up brushes (C) convey the dirt into the debris
collector (Fig. 1/6).
8. Adjusting the feed-in brushes (Fig. 8)
The feed-in brushes can be adjusted infinitely as required (5).
9. Emptying the debris collector (Fig. 9)
After sweeping up metal, glass or sharp objects, wear heavy-duty work gloves when
emptying the debris collector.
10. Height adjustment and folding of the push bar (Fig. 10/11)
Remove the adjustment nuts (2) and the relevant screws. Select one of the three holes (F)
as required, then re-tighten the adjustment nuts (2) and the relevant screws. The push bar
can be set to three different heights over a rang of approximately 98cm - 94cm - 89cm.
The push bar can be folded as shown in Fig. 11.
11. Disposal and recycling
The equipment is supplied in packaging to prevent it from being damaged in transit. The
raw materials in this packaging can be reused or recycled. The equipment and its
accessories are made of various types of material, such as metal and plastic. Defective
components must be disposed of as special waste.
Ask your dealer or your local council.
Inhaltsverzeichnis
Andere TOPMAQ Gebläse Handbücher
