Topwing SkyEasy Smart FPV Bedienungsanleitung
Quick Start on SkyEasy Smart FPV Glider
Gyro Mode Selection
Self-leveling: Put the left switch to the middle
position.
Stabilizing: Put the left switch to the upper position.
Normal: Put the left switch to the lower position.
How to Use the Special Features
In order to use auto pilot features, you need to
switch the transmitter to self-leveling mode firstly.
That means putting the left switch to the middle
position.
Auto Take-off: Toss the plane out into air, the motor
will be activated automatically and the plane will fly by itself.
Auto Pilot: While in the air, the plane will fly at the pre-set height in the direction that tossed out. The plane will return home
when reached the pre-set distance. And then fly around the launch point with the pre-set max radius and minimum altitude.
One-Key Return Home: Press the “H”key on Tx, the plane will return to the point where it is launched and circle around the
launch point.
Notice: flight parameters, such as distance, circling diameter and height, can be pre-set in your transmitter.
How to setup the flight parameters: press “ESC”to enter menu, and select “6. GPS Setup”. Min alt: minimum altitude; Far dst:
maximum distance; Max rad: maximum radius; Min spd: minimum stall speed.
Warning: it is highly recommended that the pilot doesn’t wear the FPV goggle when precise operations are required, such as
landing and take-off. Otherwise, there will be a danger of crash.
How to Bind Tx with Rx
The Tx and Rx are pre-binded in factory. So no binding required. If there is a situation when binding is required, please follow
the instructions as below:
Get to Start
(1) install the vertical wing with glue (2) install the main wing (3) install the propeller
(1) Install the flight battery, and keep the plane still on the ground.
(2) Press the button on receiver, and then put the transmitter close to plane
and keep pressing button “A”for 5 seconds while power on the transmitter.
Notice:
(1) Please keep the plane still while binding, to avoid any interference.
(2) Please avoid binding when other similar binding is going on.
Notice:
1. Check the control surfaces and gyro response before each flight. And make sure the control surfaces are level while gyro off.
2. The throttle and elevator will not function properly if the GPS didn’t receive location signals. Press “ ” button to check
GPS information.
3. If the plane can’t work properly, try to turn off the plane and transmitter, and power on again.
How to Use the FPV Goggle
The FPV goggle is preset to be in the same band as the video transmitter on the plane. So no any setup required. If there is a
situation of band change required, you can follow the instructions on the manual for FPV goggle. And the band of video
transmitter as below:
Step 1: Long press the button on video transmitter to enter setup;
Step 2: Short press the button to choose channel (CH1-CH8);
Step 3: Long press the button to enter frequency setup. Short press to choose frequency (A, B, C, D, E, F);
Step 4: Long press the button to enter power setup. Short press to choose the power (H: 200mw, U: 100mw, L: 25mw, -: off);
Step 5: Long press the button to exit setup.
Battery Warning
2S 7.4V 25C recommended for flight battery; 2S 7.4V power for FPV goggle; 3.7V 200mAh for video transmitter. If you will
stock the battery for a long time, please keep the battery voltage at 3.75v-3.85v per sheet.
SHENZHEN TOPWING INTELLIGENCE TECHNOLOGY CO., LIMITED
Customer Service: info@topwing.com.cn
(4) plug aileron servo into
channel 2 in receiver
(5) power on the controller
and then the plane
(6) power on the video transmitter and
then the FPV goggle
Inhaltsverzeichnis
Andere Topwing Fernbedienung Handbücher
Beliebte Fernbedienung Handbücher anderer Marken
Panasonic
Panasonic EUR7622KB0 Bedienungsanleitung
Bang & Olufsen
Bang & Olufsen Beo4 Bedienungsanleitung
Sunwave Tech.
Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung
Multiplex
Multiplex PROFI TX 9 Bedienungsanleitung
One Remote
One Remote RMB4 Bedienungsanleitung
FUTABA
FUTABA 9ZAP - PART2 Bedienungsanleitung
