Tork DGS180 Bedienungsanleitung

NOTE: Unit can be fully programmed using battery

power only.

4. Reinstall unit by reversing step #1 above and con-

nect wires to unit as per suggested wiring dia-

grams. See illustration on enclosure label.

KEY FUNCTIONS

DAY/MONTH: Press to advance the day in the CLK

and SKIP modes. Press to advance the month in the

DATE mode.

HOUR/DATE: Press to set the Hours in the CLK

mode and in the Schedule SET mode. Press to

advance date in the DATE mode.

MIN/YEAR: Press to set the Minute in the CLK mode

and in the schedule SET mode. Press to advance

Year in the DATE mode.

OVERRIDE: Press to execute or terminate a signal.

MODE: Press to advance to next mode without

affecting the display information. Sequence is: RUN,

CLK, DATE, schedule SET, SIG 1, SIG 2, Skip (SP).

In the SET mode, unit automatically reverts to the

RUN mode if no entries are made for a short peri-

od of time.

SP DAY: Press to set or delete SKIP days (those on

which no signal schedule is executed)

SIG/SEC: Press to select signal 1, signal 2, or no

event - or to set the duration of signals in seconds.

ENTER: Press to store the displayed information into

memory. Information will not be stored until

ENTER is pressed.

NOTE: During settings, each press of the key will

advance one number. For rapid advance, hold key in.

DAY

MONTH HOUR

DATE MIN

YEAR OVER-

RIDE

MODE SP

DAY SIG

SEC ENTER

TORK DGS180

DIGITAL SIGNAL TIMER

24 HOUR WITH DAY OMIT

READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT

FEATURES

Single channel signal timer with 2 duration settings

288 signals in 5 minute increments

24 Hour scheduling with day omitting

Battery back-up uses standard 9 volt non-recharge-

able (not supplied). Lithium averages 450 hours of

power outage; Alkaline averages 175 hours

Manual activation or deactivation of signal

Automatic daylight saving - user selectable

Automatic leap year compensation

AM/PM or 24 hour format - user selectable

INSTALLATION

UNIT IS TO BE INSTALLED BY A LICENSED ELECTRICIAN

1. To remove unit from enclosure: Push tab on right

to swing unit to the left and remove.

2. Mount the enclosure at eye level using screws or

other suitable fastening device. Bring supply and

load wires in through bottom or side knockouts.

DO NOT USE TOP.

Input wires to controller must be dedicated i.e. no

other loads connected to the same circuit.

3. Install a standard 9 volt lithium or alkaline battery

(not supplied) by gently squeezing the right side of

the battery cover on the front of the unit and pull

to open. Pull out the battery connector and con-

nect the battery. Reinstall battery cover. Lithium

should be replaced every 3-5 years, Alkaline

every year.

http://waterheatertimer.org/Tork-Digital-timers-and-manuals.html#DGS

NOTE: Unit can be fully programmed using battery

power only.

4. Reinstall unit by reversing step #1 above and con-

nect wires to unit as per suggested wiring dia-

grams. See illustration on enclosure label.

KEY FUNCTIONS

DAY/MONTH: Press to advance the day in the CLK

and SKIP modes. Press to advance the month in the

DATE mode.

HOUR/DATE: Press to set the Hours in the CLK

mode and in the Schedule SET mode. Press to

advance date in the DATE mode.

MIN/YEAR: Press to set the Minute in the CLK mode

and in the schedule SET mode. Press to advance

Year in the DATE mode.

OVERRIDE: Press to execute or terminate a signal.

MODE: Press to advance to next mode without

affecting the display information. Sequence is: RUN,

CLK, DATE, schedule SET, SIG 1, SIG 2, Skip (SP).

In the SET mode, unit automatically reverts to the

RUN mode if no entries are made for a short peri-

od of time.

SP DAY: Press to set or delete SKIP days (those on

which no signal schedule is executed)

SIG/SEC: Press to select signal 1, signal 2, or no

event - or to set the duration of signals in seconds.

ENTER: Press to store the displayed information into

memory. Information will not be stored until

ENTER is pressed.

NOTE: During settings, each press of the key will

advance one number. For rapid advance, hold key in.

DAY

MONTH HOUR

DATE MIN

YEAR OVER-

RIDE

MODE SP

DAY SIG

SEC ENTER

TORK DGS180

DIGITAL SIGNAL TIMER

24 HOUR WITH DAY OMIT

READ INSTRUCTIONS CAREFULLY BEFORE SETTING UNIT

FEATURES

Single channel signal timer with 2 duration settings

288 signals in 5 minute increments

24 Hour scheduling with day omitting

Battery back-up uses standard 9 volt non-recharge-

able (not supplied). Lithium averages 450 hours of

power outage; Alkaline averages 175 hours

Manual activation or deactivation of signal

Automatic daylight saving - user selectable

Automatic leap year compensation

AM/PM or 24 hour format - user selectable

INSTALLATION

UNIT IS TO BE INSTALLED BY A LICENSED ELECTRICIAN

1. To remove unit from enclosure: Push tab on right

to swing unit to the left and remove.

2. Mount the enclosure at eye level using screws or

other suitable fastening device. Bring supply and

load wires in through bottom or side knockouts.

DO NOT USE TOP.

Input wires to controller must be dedicated i.e. no

other loads connected to the same circuit.

3. Install a standard 9 volt lithium or alkaline battery

(not supplied) by gently squeezing the right side of

the battery cover on the front of the unit and pull

to open. Pull out the battery connector and con-

nect the battery. Reinstall battery cover. Lithium

should be replaced every 3-5 years, Alkaline

every year.

TO SET CLOCK

Press MODE key; display shows CLK.

Press DAY/MONTH key to select today’s day. Press

HOUR key to set present hour (check AM/PM). Press

MIN key to set present minutes. Press ENTER key.

Unit now stores present time. Seconds are set at

zero.

DAYLIGHT SAVING

The user may select either standard U.S. option or no

daylight saving at all.

1. U.S. OPTION: Daylight saving is automatically set

when entering the current month/date/year. The

unit will add one hour on the first Sunday in April,

and subtract one hour on the last Sunday in

October. You never need to look up the tables, or

enter the spring and fall correction dates yourself.

2. NO DAYLIGHT SAVING: The unit will not be con-

figured for daylight saving time correction by not

entering the month/date/year.

TO SET DATE

NOTE: ENTER ONLY IF AUTOMATIC DAYLIGHT

SAVING IS DESIRED. IF NOT REQUIRED, DO

NOT

SET DATE. INSTEAD, SKIP THE FOLLOWING

SECTION AND PRESS MODE KEY UNTIL DIS-

PLAY SHOWS SET.

SU AM

CLK

SETTING THE UNIT

SELECT AM/PM OR

24 HOUR MILITARY FORMAT

Upon powering up the unit, model number 180S

appears on the screen. The LCD will next display

12H which is an automatic (AM/PM) format.

Press ENTER to keep AM/PM format or press HOUR

key to alter 24 hour (Military) format and then press

ENTER.

Once the ENTER is pressed, unit goes to RUN mode

You can recognize that the unit is in the RUN mode

when the real time (including seconds) is displayed.

NOTE: Once you select and ENTER the above for-

mat (either AM/PM or 24 hour military), you can not

alter it without removing all power to the unit by dis-

connecting the battery and line power.

SU AM

OFF

TO SET CLOCK

Press MODE key; display shows CLK.

Press DAY/MONTH key to select today’s day. Press

HOUR key to set present hour (check AM/PM). Press

MIN key to set present minutes. Press ENTER key.

Unit now stores present time. Seconds are set at

zero.

DAYLIGHT SAVING

The user may select either standard U.S. option or no

daylight saving at all.

1. U.S. OPTION: Daylight saving is automatically set

when entering the current month/date/year. The

unit will add one hour on the first Sunday in April,

and subtract one hour on the last Sunday in

October. You never need to look up the tables, or

enter the spring and fall correction dates yourself.

2. NO DAYLIGHT SAVING: The unit will not be con-

figured for daylight saving time correction by not

entering the month/date/year.

TO SET DATE

NOTE: ENTER ONLY IF AUTOMATIC DAYLIGHT

SAVING IS DESIRED. IF NOT REQUIRED, DO

NOT

SET DATE. INSTEAD, SKIP THE FOLLOWING

SECTION AND PRESS MODE KEY UNTIL DIS-

PLAY SHOWS SET.

SU AM

CLK

SETTING THE UNIT

SELECT AM/PM OR

24 HOUR MILITARY FORMAT

Upon powering up the unit, model number 180S

appears on the screen. The LCD will next display

12H which is an automatic (AM/PM) format.

Press ENTER to keep AM/PM format or press HOUR

key to alter 24 hour (Military) format and then press

ENTER.

Once the ENTER is pressed, unit goes to RUN mode

You can recognize that the unit is in the RUN mode

when the real time (including seconds) is displayed.

NOTE: Once you select and ENTER the above for-

mat (either AM/PM or 24 hour military), you can not

alter it without removing all power to the unit by dis-

connecting the battery and line power.

SU AM

OFF

Press mode key until display shows DATE.

Press MONTH key to select month. Press DATE key

to set today’s date. Press YEAR key to set present

year. Press ENTER key. Unit now stores present

date.

Note: If unit has correct entry for the calendar, then

the unit will go into the SET mode. If the calendar has

an incorrect entry, then the unit will stay in the DATE

mode, with MM--YY displayed, signifying that the

date does not correspond with the month, and/or

year, i.e. Feb. 31,1996. If this occurs, set the correct

date, and then press ENTER.

TO SET SCHEDULE

For convenience, write out your desired schedule on

a separate piece of paper. If display does not show

SET then press MODE key until display shows SET.

The display will show 12:00 AM.

1. Press HOUR key to set hour (check AM/PM)

2. Press MIN key to set minutes

Note: Minutes advance in intervals of 5 because

scheduling execution has 5 minute resolution.

DATE

SET

3. Press SlG/SEC key to set signal 1 or signal 2.

(Actual duration of signals will be set later.)

4. Press ENTER key to store the signal event.

REPEAT ABOVE STEPS FOR ALL DESIRED SIG-

NAL EVENTS

Note: After each event is entered, the clock (in the

set mode only) automatically advances 5 minutes.

5. Press MODE key to return to RUN mode.

TO SET SIGNAL DURATIONS

1. Press MODE key until display shows SIG 1 and

00.

2. Press SIG/SEC key to set duration time in sec-

onds (1-99).

3. Press ENTER key to store the information.

Display now shows SIG 2.

4. Again press SIG/SEC key to set duration time in

seconds (1-99). Press ENTER key.

TO SET SKIP DAYS

1. Press MODE key until display shows SP

2. Press DAY/MONTH key and SU starts flashing.

3. If you want Sunday to be a skip day, press SP

DAY key and SU will remain solid. Next day (MO)

will begin flashing. If you do not want Sunday to

be a skip day, press DAY/MONTH key to advance

to the first desired Skip Day. Then press SP DAY

key.

4. If you want to delete a previously set skip day, press

DAY/MONTH key to advance to that day - then

(when Flashing) Press SP DAY key to delete it.

Summary: SP DAY key sets a flashing day as a

SKIP day and also eliminates a constantly dis-

played day from Skip day status. DAY/MONTH

key advances the days.

Press mode key until display shows DATE.

Press MONTH key to select month. Press DATE key

to set today’s date. Press YEAR key to set present

year. Press ENTER key. Unit now stores present

date.

Note: If unit has correct entry for the calendar, then

the unit will go into the SET mode. If the calendar has

an incorrect entry, then the unit will stay in the DATE

mode, with MM--YY displayed, signifying that the

date does not correspond with the month, and/or

year, i.e. Feb. 31,1996. If this occurs, set the correct

date, and then press ENTER.

TO SET SCHEDULE

For convenience, write out your desired schedule on

a separate piece of paper. If display does not show

SET then press MODE key until display shows SET.

The display will show 12:00 AM.

1. Press HOUR key to set hour (check AM/PM)

2. Press MIN key to set minutes

Note: Minutes advance in intervals of 5 because

scheduling execution has 5 minute resolution.

DATE

SET

3. Press SlG/SEC key to set signal 1 or signal 2.

(Actual duration of signals will be set later.)

4. Press ENTER key to store the signal event.

REPEAT ABOVE STEPS FOR ALL DESIRED SIG-

NAL EVENTS

Note: After each event is entered, the clock (in the

set mode only) automatically advances 5 minutes.

5. Press MODE key to return to RUN mode.

TO SET SIGNAL DURATIONS

1. Press MODE key until display shows SIG 1 and

00.

2. Press SIG/SEC key to set duration time in sec-

onds (1-99).

3. Press ENTER key to store the information.

Display now shows SIG 2.

4. Again press SIG/SEC key to set duration time in

seconds (1-99). Press ENTER key.

TO SET SKIP DAYS

1. Press MODE key until display shows SP

2. Press DAY/MONTH key and SU starts flashing.

3. If you want Sunday to be a skip day, press SP

DAY key and SU will remain solid. Next day (MO)

will begin flashing. If you do not want Sunday to

be a skip day, press DAY/MONTH key to advance

to the first desired Skip Day. Then press SP DAY

key.

4. If you want to delete a previously set skip day, press

DAY/MONTH key to advance to that day - then

(when Flashing) Press SP DAY key to delete it.

Summary: SP DAY key sets a flashing day as a

SKIP day and also eliminates a constantly dis-

played day from Skip day status. DAY/MONTH

key advances the days.

5. When all selected skip days are displayed as con-

stant. Press ENTER key. Unit goes to run mode

and clock shows real time. Skip day(s) will flash

when its day of the week is reached.

6. To skip schedules on all days (such as for vaca-

tion shut-down) press the SP DAY key when unit

is in the run mode. Current day of the week will

flash and a “D” will appear in the upper right dis-

play. To resume normal schedule, press SP DAY

key again.

REVIEW/MODIFY

SCHEDULE:

1. Press MODE key until display shows SET. The

first chronological event will be displayed.

2. Press ENTER repeatedly to continue reviewing

the other scheduled events. After all are dis-

played, unit will show 12:00 AM and new entries

may be made.

3. To modify an event, press mode key until display

shows SET. Then press ENTER key until the

scheduled event is displayed. Then press the

SlG/SEC key to change to SIG 1, SIG 2, or blank

which indicates delete entirely. PRESS ENTER

KEY AFTER EACH MODIFICATION.

SKIP DAYS:

Press Mode key until display shows SP. All of the

skip days are displayed as solid. To modify, use

DAY/MONTH and SP DAY keys. (See section “TO

SET SKIP DAYS”).

OVERRIDE:

Override can only be executed when unit is in the run

mode and is accomplished by pressing the OVER-

RIDE key.

When pressed, duration time of signal 1 will be exe-

cuted. If no specific duration had been set for signal

1, then it will sound for 1 second.

If either signal 1 or signal 2 are in progress when

OVERRIDE key is pressed, then the signal will be

terminated.

MLI-91(A)

TORK

1 GROVE STREET, MT. VERNON, NY 10550 TEL: 914-664-3542

FAX: 914-664-5052

Inhaltsverzeichnis

Andere Tork Timer Handbücher

Beliebte Timer Handbücher anderer Marken

Intermatic

Intermatic P1131 Bedienungsanleitung

Learning Resources

Learning Resources Time Tracker mini Bedienungsanleitung

CEBEK

CEBEK I-215 Bedienungsanleitung

Somogyi

Somogyi home TS MD 5 Bedienungsanleitung

Profile

Profile 010200280 Bedienungsanleitung

Gizmo

Gizmo T4 Bedienungsanleitung

Tekmar

Tekmar Timer 031 Bedienungsanleitung

Daikin

Daikin DST301B61 Bedienungsanleitung

sisel

sisel ENDA ETM2432 Bedienungsanleitung

B&Q

B&Q TE103 Bedienungs- und Wartungshandbuch

Hozelock

Hozelock AC Plus 2700 Bedienungsanleitung

GIC

GIC Eliro V7DDSS3Eliro V7DFTS3 Bedienungsanleitung

Emos

Emos EMT400F Bedienungsanleitung

FarmTek

FarmTek Polaris Bedienungsanleitung

Maximum

Maximum CRONUS Bedienungsanleitung

Uberhaus

Uberhaus TD133B Bedienungsanleitung

Clas Ohlson

Clas Ohlson 31-3766 Bedienungsanleitung

Gewiss

Gewiss 90 AM Series Bedienungsanleitung