Tornado Genesis Bedienungsanleitung

Genesis

Car

1N00-501 user manual

Manufactured in the United Kingdom

RoHS

1N00-501 Genesis Car User Manual v3 05/19

©Tornado International Ltd. 2019 -1- Condential

Your serial number is:

Please quote this number when ordering

parts or seeking telephone assistance.

Company information

Telephone

+44(0)121-773-1827

for:

Technical help - Service department

Parts and accessories - Parts department

Unit sales - Katie Roberts

Comments - Stuart Bland

Website

www.tornado-uk.com

sales@tornado-uk.com

Address

Tornado International Ltd

Unit 20

Stirchley Trading Estate

Hazelwell Road

Stirchley

Birmingham

B30 2PF

England, United Kingdom

This product is manufactured in the European Economic Area and is manufactured to comply with

all relevant legislation.

Do not dispose of this product in landll. Contact Tornado International Ltd for information

regarding disposal in compliance with 2012/19/EU.

RoHS This product and all constituent components to the best of our knowledge complies with

2011/65/EU.

1N00-501 Genesis Car User Manual v3 05/19

©Tornado International Ltd. 2019 -2- Condential

Please take note of the information in shaded areas. If you have any questions with regard to the correct

installation or operation of the product please contact Tornado International Ltd.

Important – please read this!

This manual is provided in good faith and is believed to be accurate. Because Tornado International have no

control over the manner in which the product is used, users should satisfy themselves that any information

or instruction contained in this manual is appropriate for the conditions under which the product is being

installed and operated.

In the interest of product development, Tornado International reserves the right to alter or modify the

product as necessary.

Conventions used in this manual

For clarity the following conventions are used in this manual:

Paragraph Heading Meaning

Tip!

Note!

Caution!

Warning!

Information which will assist in the operation of the

product

Information which is important for the correct

operation of the product.

Information which is VITAL to avoid injury to

persons or damage to the product.

Information which is VITAL to avoid serious injury

to personnel or the public.

1N00-501 Genesis Car User Manual v3 05/19

©Tornado International Ltd. 2019 -3- Condential

Introduction

Thank you for purchasing this quality product from Tornado International Ltd. It will give you many years of

trouble free service and if used in a suitable site will provide consistent prots.

Please read and understand this manual before using the equipment.

This manual contains the following sections;

1.00 Installation guide Page 5

This section will guide you through the installation process.

2.00 Operating procedures Page 16

Directions for daily operation of the equipment.

3.00 Detailed overview of the system Page 17

Here you will nd detailed information about each part of the system with hints and cautions about the

correct operation of the equipment.

4.00 Periodic service Page 47

Little is required in the way of periodic service. However time spent in following these procedures will pay

dividends in improved reliability and service life.

5.00 Fault nding Page 49

Should any faults arise during operation, consult this section to help diagnose problems.

This manual is for a car set operating on a loop aerial system at a frequency of 120KHz. Your set may use a

dierent system or frequency. Please contact Tornado quoting your serial number if you are unsure about

aspects of the installation or operation of your system.

1N00-501 Genesis Car User Manual v3 05/19

©Tornado International Ltd. 2019 -4- Condential

1.00 Installation guide

1.01 On delivery

Before opening crates

1. Check the number of crates delivered agrees with the number on the shipping documents.

2. Inspect the crates for damage. If any damage is visible note the crate number, and the position and

extent of the damage. If the crates are not to be opened immediately, the shipping company should be

notied as soon as possible. If the crates are to be opened at this time, wait until the product is inspected

for damage.

3. The crates should be moved to a position close to the operating area before opening.

4. The crates should be opened carefully, the contents removed and the quantities checked against the

shipping notes. A product identication chart can be found at Appendix A (page 51). If any damage was

noted on the outside of the crates, the product next to the damage should be inspected carefully. Any

damage should be notied to the shipping company as soon as the product is unpacked. Any shortage

should be notied to Tornado International Ltd. in writing (letter, fax or e-mail) as soon as possible and in

any event not later than 5 days after receipt.

Before installation

All equipment designed to operate o mains voltage supply (100V to 240V) is supplied with a connecting

plug where available. Ensure that the required number of plugs and sockets are available before starting

the installation.

Caution!

Check that the supply voltage matches the voltage setting on the front of the PSU and Charger cases. (see

1.04 Dia. 1 and 1.05 Dia. 1)

Tools & items required;

Small at screwdriver

Medium at screwdriver

Medium cross point screwdriver

Power drill

8mm drill bit

51mm hole cutter

10mm socket and ratchet

Socket set or adjustable spanner

Staple gun or 3mm cable clips

7mm cable clips

10 of each coin/token/currency note used

(These are not supplied with the unit)

1N00-501 Genesis Car User Manual v3 05/19

©Tornado International Ltd. 2019 -5- Condential

1.02 Setting out the equipment:

1. Before starting the installation place the consoles on the oor in the position they are to be mounted. The

consoles may be mounted either indoors or outside. Console number “1”should be on the left with the

consoles running in numerical order to the right.

2. Place the power supply unit (PSU) in the position it will be used.

Caution!

The PSU must be mounted in such a position that the public do not have access to it.

3. Place the chargers in the position they will be used. Air vents at the top and bottom of the case provide

cooling. It is important that the chargers are positioned so that there is an uninterrupted ow of cool air

over the vents.

Caution!

The chargers must be mounted indoors and in such a position that the public do not have access to them.

They must be protected from water.

4. Check that the PSU and charger mains cables will reach the electric supply sockets.

5. Lay out the 24V PSU cable and check that it is long enough to reach from the master console to the PSU.

Note!

The PSU cable must not be lengthened without consulting Tornado International Ltd.

Tip!

The master console can be identied by an additional door to the right of the coin acceptor door. It is usual-

ly numbers 3/4 or 5/6. It is the console with the transmitter inside.

6. If you have more than one console open the console door (the key is in the spares pack) and locate the

console cable coiled up inside. Check that the cables from all additional consoles reach the console connec-

tion sockets inside the master console.

Note!

The console cables must not be lengthened without consulting Tornado International Ltd.

When you have satised yourself that all of the units are suitably positioned the installation can begin.

1N00-501 Genesis Car User Manual v3 05/19

©Tornado International Ltd. 2019 -6- Condential

1.03 Consoles

The consoles are usually mounted on a fence or low wall. The lip (See Dia. 3) at the top of the console

serves to locate the console on the top of the wall or fence and assists in the mounting process. The lip

may be removed if required by marking a line along the top of the console and cutting along the line with

a hacksaw. There are 4 mounting holes in the back of the console and large cable holes on the back and

underside of the console to route the console connection cables. (See Dia. 2)

Coin acceptor door

Access door

(Master console only - pictured)

Credit display Driving controls

Credit button

Dia. 1 - Console

Dia. 3 - Lip removal (if required)

Mark this line and

cut with a hacksaw

Dia. 2 - Console rear

Mounting holes

Cable routing holes

(unused holes should be

capped)

1N00-501 Genesis Car User Manual v3 05/19

©Tornado International Ltd. 2019 -7- Condential

Mounting the consoles

1. With the coin acceptor door open the console should be placed in the chosen position on the wall or

fence to which it is to be xed.

2. The position of the mounting holes (and cable holes if required) should be marked on the wall or fence

using a scribe or pencil from inside the console.

3. The console can then be removed and using an 8mm drill bit, the four mounting holes can be drilled in

the wall or fence. Any required cable holes can then be drilled in the wall or fence, using a 51mm hole saw.

4. Locate the console mounting bolts in the spares pack and position the bolts with one washer under the

head through the wall or fence from the model operating side.

5. Prepare four washers and wing nuts. With a helper holding the bolts in place, lift the console into position

and locate it onto the mounting bolts. Fit a washer and wing nut to each bolt and tighten securely.

6. Repeat for each console.

Caution!

Whenever possible use the predrilled mounting holes in the rear of the console (See Dia. 2). If this is not

possible, alternative holes may be drilled in the back of the console only after checking that there are no

items or electronics inside the console in the area to be drilled. Any damage caused by not following this

instruction is the responsibility of the installer.

Dia. 4 - Console mounting bolt

WashersWing nutBolt

1.04 Power supply unit (PSU)

The PSU can either be placed on a shelf or hung on a wall using the slots on the back plate (see Dia. 2). To

wall mount the PSU, use the lugs on the PSU backplate as a template and a draw the two drilling locations

on the wall. Drill the holes and insert the rawl plugs and screws provided in the spares pack (1F00-001 -

Charger & PSU xings) the create the mounts.

Locate it in close proximity to a wall outlet, but do not plug it in yet.

Caution!

The PSU must be mounted in such a position that the public do not have access to it.

Mains input

Output to transmitter motherboard

located in master console

Dia. 1 - The PSU Dia. 2 - PSU back plate Lug

Lug

1N00-501 Genesis Car User Manual v3 05/19

©Tornado International Ltd. 2019 -8- Condential

1.05 Chargers

Air vents

Charge indicators

The chargers must be mounted on a wall using the slots in the rear of the case (see Dia. 2). Draw a 325mm

horizontal line on the wall on which you want to mount the charger case and drill a hole at each end. Use

the rawl plugs and screws provided in the spares pack (1F00-001 - Charger & PSU xings) to create the

mounts.

Air vents at the top and bottom of the case provide cooling. It is important that the chargers are posi-

tioned so that there is an uninterrupted ow of cool air over the vents.

Caution!

The chargers must be mounted indoors and in such a position that the public do not have access to them.

They must be protected from water.

The chargers should now be connected to the electric supply. The batteries are fully charged when the

unit is dispatched from the factory, however if the unit has been in transit for some time it might be

prudent to charge the batteries whilst the rest of the installation is carried out. See the section “3.20

Battery charger” for how to charge the batteries.

Mains input

Dia. 1 - The charger case

Mounting slots

Dia. 2 - Case mounting slots

Battery leads

Air vents

1N00-501 Genesis Car User Manual v3 05/19

1.06 Routing the console cables

Dia. 1 – The transmitter motherboard showing the master console connection sockets

(Inside the access door of the master console)

Each console has a grey cable coiled inside the console on the side nearest the master console. Each of

these has to be routed out of the console and into the master console. The cables should be supported

using 8mm cable clips every 30cm.

1. Open the coin acceptor door and locate the console cable.

2. Uncoil the cable and feed the plug out of the console using one of the large holes in the back or bottom

as required.

3. Route the cable to the master console and t the plug into the correct numbered socket on the trans-

mitter motherboard (See Dia. 1) (The socket numbers are on the transmitter motherboard cover). Do not

x the cables in position at this time.

4. Repeat the routing for all console cables. It should be noted that the cable for the master console is

tted at the factory. All of the console cables are the same length so some surplus will remain for consoles

close to the master console.

5. Leaving a small loop of cable in the master console, x the cables in position starting at the master

console and working toward the standard console(s).

6. Coil up any excess cable and place it inside the standard console to one side, ensuring that the coil of

cable does not interfere with the operation of any of the console controls.

7. Repeat the cable xing for any other consoles.

Note!

When you have nished connecting all of the supplied consoles check to ensure all of the master console

connection sockets have either a console connected or a dummy plug installed.

1N00-501 Genesis Car User Manual v3 05/19

Andere Handbücher für Genesis

Inhaltsverzeichnis

Andere Tornado Controller Handbücher

Tornado

Tornado Genesis Super Trucks Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch