Toro XP300-02 Kurzanleitung

XP-300 Series Sprinklers

Installation & Service Instructions

Introduction ____________________________________________________________

The XP-300 Series Sprinkler is a multiple-stream gear-driven sprinkler ideal for residential and commercial applications.

Sprinkler arc is determined by an rc Disc™ located under the nozzle. Eleven arc discs are available to cover virtually

any watering requirement. Three nozzle sizes are available to provide from 1.43–10.81 GPM flow and produce watering

radii from 36'–43'. fourth nozzle which provides 1.01–5.28 GPM flow and produces watering radii from 28'–31' is avail-

able only as a service replacement part.

To assure maximum performance from your XP-300 Shrub, Lawn or Hi-Pop sprinklers, please read the instructions com-

pletely prior to installation or servicing procedures.

Specifications___________________________________________________________

Nozzle Performance Data__________________________________________________

* ▲▲Precipitation rates are for triangular spacing, shown in inches per hour, calculated at 50% of diameter.

■■Precipitation rates are for square spacing, shown in inches per hour, calculated at 50% of diameter.

ll performance specifications are based on the stated working pressure available at the base of the sprinkler head.

* * 05 Nozzle is available only as a service replacement part.

Nozzle Performance

❚Radius: 28'–43'

❚Flow rate: 1.01–10.80 GPM

❚Trajectory: 28°

❚Maximum height of spray:

❚

#05 Nozzle: 9' 3" @ 50 PSI

❚

#07 Nozzle: 9' 1" @ 50 PSI

❚

#09 Nozzle: 9' 1" @ 50 PSI

❚

#10 Nozzle: 9' 6" @ 50 PSI

Shrub

❚Recommended operating

pressure: 35–60 PSI

❚Maximum operating

pressure: 75 PSI

❚1⁄2" & 3⁄4" NPT female

thread inlet

❚Dimensions:

❚

Body diameter: 13⁄4"

❚

Height: 61⁄2"

Hi-Pop

❚Recommended operating

pressure: 35–60 PSI

❚Maximum operating

pressure: 75 PSI

❚Pop-up: 123⁄4"

❚Pop-up to nozzle: 121⁄2"

❚3⁄4" NPT female thread

bottom and side inlet

❚Side inlet – 7" from top of

sprinkler to center of side

inlet

❚Dimensions:

❚

Body diameter: 23⁄8"

❚

Cap diameter: 3"

❚

Height: 161⁄2"

Lawn Pop-Up

❚Recommended operating

pressure: 35–60 PSI

❚Maximum operating

pressure: 75 PSI

❚Pop-up: 33⁄4"

❚Pop-up to nozzle: 31⁄2"

❚3⁄4" NPT female thread

inlet

❚Dimensions:

❚

Body diameter: 23⁄8"

❚

Cap diameter: 3"

❚

Height: 61⁄8"

360° 270° 250° 225° 210° 195° 180° 165° 140° 115° 90°

Prec. Rates*

Nozzle PSI Rad. ▲▲■■Gallons Per Minute

35 28' .57 .50 4.04 3.03 2.81 2.53 2.36 2.19 2.02 1.85 1.57 1.29 1.01

40 29' .56 .48 4.23 3.24 3.00 2.70 2.52 2.34 2.16 1.98 1.68 1.38 1.08

05 50 30' .60 .52 4.83 3.62 3.35 3.02 2.82 2.62 2.42 2.21 1.88 1.54 1.21

60 31' .61 .53 5.29 3.97 3.67 3.31 3.09 2.87 2.65 2.42 2.06 1.69 1.32

35 36' .49 .42 5.70 4.28 3.93 3.60 3.31 3.08 2.85 2.62 2.22 1.82 1.43

40 38' .47 .41 6.14 4.61 4.24 3.87 3.56 3.32 3.07 2.82 2.39 1.96 1.54

07 50 40' .48 .41 6.85 5.14 4.73 4.32 3.97 3.70 3.43 3.15 2.67 2.19 1.71

60 41' .49 .43 7.47 5.60 5.15 4.71 4.33 4.03 3.74 3.44 2.91 2.39 1.87

35 38' .53 .46 6.94 5.21 4.79 4.37 4.03 3.75 3.47 3.19 2.71 2.22 1.74

40 39' .54 .47 7.43 5.57 5.13 4.68 4.31 4.01 3.72 3.42 2.90 2.38 1.86

09 50 41' .55 .48 8.38 6.29 5.78 5.28 4.86 4.53 4.19 3.85 3.27 2.68 2.10

60 43' .56 .48 9.26 6.95 6.39 5.83 5.37 5.00 4.63 4.26 3.61 2.96 2.32

35 37' .65 .56 7.95 5.96 5.49 5.01 4.61 4.29 3.98 3.66 3.10 2.54 1.99

40 39' .63 .54 8.58 6.44 5.92 5.41 4.98 4.63 4.29 3.95 3.35 2.75 2.15

10 50 41' .65 .56 9.76 7.32 6.73 6.15 5.66 5.27 4.88 4.49 3.81 3.12 2.44

60 42' .68 .59 10.81 8.11 7.46 6.81 6.27 5.84 5.41 4.97 4.22 3.50 2.70

* *

Rubber Cover Kit –Lawn Pop-Up

ttach rubber cover (optional) to sprinkler cap, using Loctite Super Bonder®(or equivalent)

adhesive as follows:

1. ssure bonding surfaces are dry and free of dirt, grease, and foreign substances.

2. Spread thin film of adhesive on underside of rubber cap cover and rubber nozzle cover.

3. ssemble immediately. Press retainer plug pins into two (2) holes in nozzle. See Figure 1.

4. pply firm pressure until set (approximately 15 seconds).

Installation Procedure

NOTE: Toro Funny Pipe®is recommended for ease of installation and accurate sprinkler

positioning when installing the XP-300 Lawn and Hi-Pop sprinklers. Unlike a rigid con-

nection, the flexible Funny Pipe link helps protect the PVC piping and fittings from break-

age due to downward or lateral sprinkler movement. XP-300 Lawn and Hi-Pop sprinklers

should be installed with top of cap level with finish grade (soil).

CAUTION

Use only Teflon Tape™to make threaded connections between polyethylene riser or barbed ell and

sprinkler body. Deterioration of sprinkler body may occur if other sealing compounds are used.

Shrub Sprinkler Installation

1. Flush all lines thoroughly prior to installing sprinkler on riser.

2. Grasp base of sprinkler by cap (not body) and screw securely onto teflon taped riser.

Do not over-torque, handtight is sufficient.

3. To align part-circle sprinkler to coverage area, locate raised alignment dot on sprinkler

shoulder (see Figure 3). lign dot with center of coverage area. If dot cannot be posi-

tioned correctly when sprinkler is tight, unscrew nozzle assembly and reposition rc Disc

to coverage area. (See Figure 6.)

4. Turn on water to system and refine part circle spray pattern.

5. djust spray radius if required (see Figure 3).

Lawn and Hi-Pop Sprinkler Installation

1. Flush all lines thoroughly prior to installing sprinkler.

2. Grasp sprinkler by body (not cap) and screw securely onto teflon taped riser or barbed ell. Do not over-torque,

handtight is sufficient.

3. To align part-circle sprinkler coverage area, locate raised dot on body and align with center of coverage area. If dot

cannot be positioned correctly when sprinkler is tight, unscrew nozzle assembly and reposition rc Disc to coverage

area (see Figure 9). NOTE: Lawn Pop-Up has only one riser tab.

4. Backfill soil around sprinkler avoiding soil contact with nozzle assembly.

5. Turn on water to system and refine part circle spray pattern.

6. djust spray radius if required (see Figure 3).

Figure 1

Figure 3

Figure 2

SHRUB

SPRINKLER

RISER SWING JOINT

B RBED FITTINGS

WITH TORO

FUNNY PIPE

DECRE SE INCRE SE

LIGNMENT

DOT

1/16" HEX

DRIVER

Shrub Sprinkler Disassembly

1. Unscrew nozzle, lift out rc Disc and rc Disc seal.

2. Unscrew cap assembly from body and remove washer seal.

3. Remove basket screen from body and flush thoroughly to remove dirt and debris.

4. Remove variable stator from body. Clean ports if clogged.

5. Remove drive assembly from body by pressing gently on outer edge of drive assembly with flat blade screwdriver.

(See Figure 4.) CAUTION

Do not apply pressure directly on center shaft of drive assembly. Push on outer edge of drive assembly

housing. Excessive force applied directly to shaft may cause permanent damage to drive assembly and

loss of sprinkler performance.

Shrub Sprinkler Resassembly

1. Invert shrub body, install drive assembly (threaded end first), variable stator and basket screen.

2. Place washer seal into cap and screw cap onto shrub body.

NOTE: Inspect Arc Disc seal for damage and replace if necessary.

3. Holding shrub body in upright position, install rc Disc seal, tapered side up. (See Figure 5.)

4. Install rc Disc, aligning center of part circle spray pattern with designated body tab. (See Figure 6.)

5. Screw nozzle assembly into drive assembly. (Do not overtighten.)

Lawn and Hi-Pop Sprinkler Disassembly

1. Using 1⁄16" hex driver, loosen set screw on Locking Cap (Hi-Pop only).

2. Unscrew cap from body and remove cap, nozzle assembly and riser from body.

3. Remove basket screen from bottom of riser. Flush thoroughly to eliminate dirt and debris.

4. Push riser assembly through cap and grasp riser between cap and nozzle assembly firmly.

5. Unscrew and remove nozzle assembly.

6. Lift out rc Disc and rc Disc seal.

7. Slowly release riser assembly and remove cap, riser seal and return spring from riser.

8. Invert riser and pry-out variable stator assembly from Lawn Pop-up by inserting a knife edge between lip of stator and

riser. Inspect stator and clean ports if clogged.

9. Remove drive assembly from riser by pressing gently on outer edge of drive assembly with flat blade screwdriver. (See

Figure 7.) On Hi-Pop models, variable stator assembly will be pressed out with drive assembly.

Figure 4

Figure 5 Figure 6

SHRUB

BODY

DRIVE SSEMBLY FL T BL DE

SCREWDRIVER

DO NOT

PRESS HERE

RC DISK

SE L RC DISK

T PERED

SHRUB

BODY

CENTER OF

SPR Y

P TTERN

USE THIS T B

FOR SPR Y

LIGNMENT

R ISED

LIGNMENT

DOT

RC DISC

SE L

BODY

T B

TOP VIEW

CAUTION

Do not apply pressure directly on center shaft of drive assembly. Push on outer edge of drive assem-

bly housing. Excessive force applied directly to shaft may cause permanent damage to drive assem-

bly and loss of sprinkler performance.

Lawn and Hi-Pop Sprinkler Reassembly

1. Invert riser, install drive assembly (threaded end first) and variable stator assembly.

NOTE: To aid installation of variable stator assembly in Hi-Pop models, mark a piece of 3⁄4" PVC pipe to 103⁄4" from one end.

Place stator assembly over end of pipe and insert into riser until stop is felt or 103⁄4"mark is even with riser bottom.

2. Place return spring, riser seal and cap on riser, compressing spring with cap.

NOTE: Inspect Arc Disc seal for damage and replace if necessary.

3. Grasp riser firmly between cap and riser top and install rc Disc seal, tapered side up (See Figure 8.)

4. Install rc Disc, aligning center of part circle spray pattern with designated riser tab. (See Figure 9.)

NOTE: Lawn Pop-up has only one riser tab for alignment of Arc Disc.

5. Screw nozzle assembly into drive assembly (do not overtighten) and slowly release cap.

6. Insert basket screen into riser bottom (Hi-pop). Press screen (Lawn Pop-up) onto riser bottom, aligning keys of screen

with keyways of riser bottom.

7. Insert riser into body (see NOTE below).

NOTE: To properly align part-circle models, insert riser assembly into body aligning marked riser keyway with marked

body key. These marks are located on bottom of riser (under screen on Lawn Pop-up) and raised dot on body exterior.

8. Screw cap onto body.

9. Tighten locking cap set screw (Hi-Pop only).

Figure 7

Figure 8 Figure 9

RISER

(Lawn Pop-Up shown)

DRIVE SSEMBLY FL T BL DE

SCREWDRIVER

DO NOT PRESS

HERE

RC DISK

SE L

RC DISK T PERED

RISER

CENTER OF

SPR Y

P TTERN

USE THIS RISER

T B FOR SPR Y

LIGNMENT

RISER T B

RC DISC

SE L

TOP VIEW

XP-300 Shrub Item Part No. Nomenclature Qty Per

No. Assy.

1 35-5460 Nozzle ssy., 5.0 GPM 1

1 XP300-02* Nozzle ssy., 7.0 GPM 1

1 XP300-03* Nozzle ssy., 9.0 GPM 1

1 XP300-04* Nozzle ssy., 10.0 GPM 1

2 360-0223 Screw, Set, Half Dog Point 2

3 XP304-00* Disc, rc, 90° 1

3 XP305-00* Disc, rc, 115° 1

3 XP306-00* Disc, rc, 140° 1

3 XP307-00* Disc, rc, 165° 1

3 XP308-00* Disc, rc, 180° 1

3 XP309-00* Disc, rc, 195° 1

3 XP310-00* Disc, rc, 210° 1

3 XP311-00* Disc, rc, 225° 1

3 XP312-00* Disc, rc, 250° 1

3 XP313-00* Disc, rc, 270° 1

3 XP314-00* Disc, rc, 360° 1

4 35-2137 Seal 1

5 35-2187 Body, Spray, Shrub 1

6 35-8580 Drive ssy. 1

7 35-2859 Stator ssy. 1

8 9-5212 Screen, Basket 1

9 9-5211 Seal 1

10 89-6094 Threaded Insert, 3/4" – 1/2" 1

11 89-8305 Base, Shrub 1

Service Parts & Assemblies

9-5209 Base, Shrub (Pre-10/97)

9-5698 Insert, 1/2"

9-5699 Insert, 3/4"

* Order through Finished Goods

Distribution System – Minneapolis

XP-300 Lawn Item Part No. Nomenclature Qty Per

No. Assy.

1 ---------- Plug, Retainer 0

2 ---------- Cover, Rubber 0

3 35-5460 Nozzle ssy., 5.0 GPM 1

3 XP300-02* Nozzle ssy., 7.0 GPM 1

3 XP300-03* Nozzle ssy., 9.0 GPM 1

3 XP300-04* Nozzle ssy., 10.0 GPM 1

4 360-0223 Screw, Set, Half Dog Point 2

5 XP304-00* Disc, rc, 90° 1

5 XP305-00* Disc, rc, 115° 1

5 XP306-00* Disc, rc, 140° 1

5 XP307-00* Disc, rc, 165° 1

5 XP308-00* Disc, rc, 180° 1

5 XP309-00* Disc, rc, 195° 1

5 XP310-00* Disc, rc, 210° 1

5 XP311-00* Disc, rc, 225° 1

5 XP312-00* Disc, rc, 250° 1

5 XP313-00* Disc, rc, 270° 1

5 XP314-00* Disc, rc, 360° 1

6 35-2137 Seal 1

7 9-4394 Cap 1

8 9-4449 Seal, Riser 1

9 9-2137 Spring, Return 1

10 35-2138 Riser 1

11 35-8580 Drive ssy. 1

12 35-2858 Stator ssy. 1

13 35-2136 Screen, Basket 1

14 9-1661 Body 1

Service Kits

600-01 Kit, Rubber Cover

(Includes Items 1 and 2)

* Order through Finished Goods

Distribution System – Minneapolis

XP-300 High-Pop

Item No. Part No. Nomenclature Quantity

Per Assy.

1 XP312-02* Nozzle ssy., with sleeve, 7.0 (Includes Items 2 and 3) 1

1 XP312-03* Nozzle ssy., with sleeve, 9.0 (Includes Items 2 and 3) 1

1 XP312-04* Nozzle ssy., with sleeve, 10.0 (Includes Items 2 and 3) 1

2 360-0223 Screw, Set, Half Dog Point 2

3 35-2249 Sleeve, Nozzle 1

4 XP304-00* Disc, rc, 90° 1

4 XP305-00* Disc, rc, 115° 1

4 XP306-00* Disc, rc, 140° 1

4 XP307-00* Disc, rc, 165° 1

4 XP308-00* Disc, rc, 180° 1

4 XP309-00* Disc, rc, 195° 1

4 XP310-00* Disc, rc, 210° 1

4 XP311-00* Disc, rc, 225° 1

4 XP312-00* Disc, rc, 250° 1

4 XP313-00* Disc, rc, 270° 1

4 XP314-00* Disc, rc, 360° 1

5 35-2137 Seal 1

6 35-4515 Cap, Locking (Includes Item 7) 1

7 360-0223 Screw, Set, Half Dog Point 1

8 35-3630 Seal, Riser 1

9 35-7579 Spring, Return 1

10 35-2247 Riser 1

11 35-8580 Drive ssy. 1

12 35-3822 Stator ssy. 1

13 9-4571 Screen, Basket 1

14 89-1960 Body 1

15 363-3187 Plug, 3/4 NPT Male 1

* Order through Finished Goods Distribution System – Minneapolis

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Toro Bewässerungssystem Handbücher

Toro

Toro Super 800 Series Bedienungsanleitung

Toro

Toro 690 Series Handbuch

Toro

Toro GreenKeeper 212 Bedienungsanleitung

Toro

Toro 860S Series Kurzanleitung

Toro

Toro MultiMatrix V-1550 Leitfaden

Toro

Toro 570Z PRX Series Bedienungsanleitung

Toro

Toro MultiStream 53246 Bedienungsanleitung

Toro

Toro TS120 Bedienungsanleitung

Toro

Toro ZSERIES 570Z Bedienungsanleitung

Toro

Toro TWRS Bedienungsanleitung

Toro

Toro 69X-01-XX Kurzanleitung

Toro

Toro 830S Series Kurzanleitung

Toro

Toro SingleStream 53261 Bedienungsanleitung

Toro

Toro TR70XT SERIES Handbuch

Toro

Toro TR50 Series Handbuch

Toro

Toro 640 Series Kurzanleitung

Toro

Toro 570Z Series Bedienungsanleitung

Toro

Toro 53763 Bedienungsanleitung

Toro

Toro P2 Series Bedienungsanleitung

Toro

Toro Infinity Stealth-T Bedienungsanleitung

Toro

Toro DRIP ZONE VALVE KIT 53749 Bedienungsanleitung

Toro

Toro TR50XT Series Handbuch

Toro

Toro TR50XT Series Handbuch

Toro

Toro TR50 Handbuch

Beliebte Bewässerungssystem Handbücher anderer Marken

Hunter

Hunter Institutional Series Bedienungsanleitung

Cellfast

Cellfast 52-305 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Star Galaxy SGQR Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product CENTRAL A Bedienungsanleitung

Oral Care Technologies

Oral Care Technologies Hydro Floss Bedienungsanleitung

Reliable

Reliable F1-300 Bedienungsanleitung

Tyco Fire Product

Tyco Fire Product Gem F892 Bedienungsanleitung

Netafim

Netafim NETBEAT Bedienungsanleitung

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Bedienungsanleitung

Tyco

Tyco CC3 Bedienungsanleitung

Reliable

Reliable F4FR Bedienungsanleitung

OpenSprinkler

OpenSprinkler OSPi Bedienungsanleitung

EINHELL

EINHELL GE-WW 5537 E Bedienungsanleitung

Valley

Valley Bender160 Bedienungsanleitung

Reliable

Reliable F1FR42 Series Bedienungsanleitung

Reliable

Reliable F1FR-300 Bedienungsanleitung

Eden

Eden 97063-EDAMZ Bedienungsanleitung

Tyco

Tyco TY-L Series Bedienungsanleitung