Toro 1800 Power Curve Bedienungsanleitung

1800 POWER CURVE

1Service Instruction TSN0001a

1. Stand the snowthrower on its wheels and position

the upper handle. Inspect the wiring for any signs of

damage. If any damage is found, do not assemble.

Contact an Authorized Service Dealer (Fig. 001 and

Fig. 002).

2. Insert the right side of the upper tubing over the

lower right side tubing (Fig. 003).

3. Insert the left side of the upper tubing into the lower

left side tubing (Fig. 004).

Fig. 001 PICT-1418

Fig. 002 PICT-1419

Fig. 004 PICT-1424

Fig. 003 PICT-1422

Upper Handle & Chute Crank Installation

1800 Power Curve Set-up / Assembly

1800 POWER CURVE

2 Service Instruction TSN0001a

4. Squeeze the upper tubes together and wiggle the

upper tubes down until the mounting holes in the

upper and lower tubing line up:

Left hand (Fig. 005):

5. Place the mounting plate over the tubes and align

the mounting plate holes with the upper and lower

tubing holes (Fig. 007).

Right hand (Fig. 006):

6. Insert the end of the chute crank rod through the

hole in the shroud (Fig. 008).

Fig. 005 PICT-1437

Fig. 006 PICT-1438

Fig. 008 PICT-1443

Fig. 007 PICT-1441

1800 POWER CURVE

3Service Instruction TSN0001a

7. Turnthechutecrankrodlightlyuntiltheattened

end drops into the slot in the chute crank gear (Fig.

009).

9. Ensure the mounting plate holes are aligned with the

upper and lower tubing holes (Fig. 011 - LH hole).

8. Firmly push the chute crank rod into the chute crank

gear until it snaps into place (Fig. 010).

10. Insert the LH bolt though the holes (Fig. 012).

Note: Insert the screws from the outside of the

mounting plate. Be careful not to damage the

internal wiring when you insert the screws.

If the wiring blocks the hole, use a blunt

end punch to route the wiring away from the

aligned holes.

Fig. 009 PICT-1444

Fig. 010 PICT-1447a

Fig. 012 PICT-1451

Fig. 011 PICT-1449

1800 POWER CURVE

4 Service Instruction TSN0001a

11. Install and tighten the nut securing the LH side (Fig.

013).

12. If the wiring blocks the hole on the RH handle, use

a blunt end punch to route the wiring away from the

aligned holes (Fig. 014 and Fig. 015).

Fig. 013 PICT-1456

Fig. 014 PICT-1459

Fig. 015 PICT-1463

1800 POWER CURVE

5Service Instruction TSN0001a

13. Insert the RH bolt through the holes and force the

punch out (Fig. 016 and Fig. 017).

14. Install and tighten the nut securing the RH side (Fig.

018).

Fig. 016 PICT-1465

Fig. 017 PICT-1466

Fig. 018 PICT-1468a

1800 POWER CURVE

6 Service Instruction TSN0001a

Discharge Chute Installation

1. Partially insert a carriage bolt through the lower

chute (Fig. 019).

3. Positionthedeectorchuteontothelowerchuteand

align the mounting holes (Fig. 021).

2. Insert a rubber washer onto the carriage bolt (Fig.

020).

4. Insertametalatwasherontothecarriagebolt(Fig.

022).

Fig. 019 PICT-1471

Fig. 020 PICT-1474

Fig. 022 PICT-1478

Fig. 021 PICT-1476

1800 POWER CURVE

7Service Instruction TSN0001a

5. Loosely install a lock nut to secure one side of the

deectorchuteassembly(Fig.023).

7. Insert the carriage bolt through the lower chute,

rubberwasheranddeectorchute(Fig.025).

6. Positionarubberwasherbetweenthedeector

chute and the lower chute while maintaining the hole

alignment (Fig. 024).

8. Installthemetalatwasherontothecarriagebolt

(Fig. 026).

Fig. 023 PICT-1479

Fig. 024 PICT-1485a

Fig. 026 PICT-1488

Fig. 025 PICT-1484

1800 POWER CURVE

8 Service Instruction TSN0001a

9. Install and tighten the locknut (Fig. 027).

11. Cyclethedeectorchutetoensureitmoveswitha

smallamountofresistance.Tootight,thedeector

chute will not move; too loose, the force of the snow

beingdischargedwillipthedeectorchuteup.

10. Tighten the locknut on the opposite side of the

deectorchuteassembly(Fig.028).

Fig. 027 PICT-1490

Fig. 028 PICT-1492

Andere Handbücher für 1800 Power Curve

Inhaltsverzeichnis

Andere Toro Schneefräse Handbücher

Toro

Toro Power Max Bedienungsanleitung

Toro

Toro CCR 2000 Bedienungsanleitung

Toro

Toro Power Max 824 OE Bedienungsanleitung

Toro

Toro 38720 Bedienungsanleitung

Toro

Toro 1800 Power Curve Bedienungsanleitung

Toro

Toro CCR Quick Clear 38563 Bedienungsanleitung

Toro

Toro 38810 Bedienungsanleitung

Toro

Toro Power Clear 39921T Bedienungsanleitung

Toro

Toro Power TRX 1428 OHXE Bedienungsanleitung

Toro

Toro Toro Snow Blower 38515 Bedienungsanleitung

Toro

Toro Power Max Heavy Duty 928 OAE Bedienungsanleitung

Toro

Toro Power Max 926 OXE S Bedienungsanleitung

Toro

Toro 38584 Bedienungsanleitung

Toro

Toro Power Max 926 OHXE Bedienungsanleitung

Toro

Toro SnowMax 724 ZXR Bedienungsanleitung

Toro

Toro 38818 Montage- und Bedienungsanleitung

Toro

Toro CCR POWERLITE 38170 Bedienungsanleitung

Toro

Toro Power Max Heavy Duty 828 OAE Bedienungsanleitung

Toro

Toro snowmax 724 QXE Bedienungsanleitung

Toro

Toro 38360 - Power Shovel 7.5 Amp Snow Thrower/Electric... Bedienungsanleitung

Toro

Toro 37797 Bedienungsanleitung

Toro

Toro 38567 Bedienungsanleitung

Toro

Toro 37779 Bedienungsanleitung

Toro

Toro CCR POWERLITE 38172 Bedienungsanleitung

Beliebte Schneefräse Handbücher anderer Marken

Murray

Murray 624504X4A Bedienungsanleitung

Blizzard

Blizzard POWER PLOW 8100PP Bedienungsanleitung

Craftsman

Craftsman 486.24837 Bedienungsanleitung

Yard-Man

Yard-Man E2B5 Bedienungsanleitung

ST ST 526 A Bedienungsanleitung

MTD

MTD 3AA Bedienungsanleitung

Ryobi

Ryobi RYAC800 Bedienungsanleitung

Poulan Pro

Poulan Pro 416829 Bedienungsanleitung

MTD

MTD 319-180-00 Bedienungsanleitung

Poulan Pro

Poulan Pro 437986 Bedienungsanleitung

Brute

Brute 1695565 Bedienungsanleitung

Egholm

Egholm City Ranger 2250 Bedienungsanleitung

Poulan Pro

Poulan Pro 420915 Bedienungsanleitung

GreenWorks

GreenWorks SNF402 Bedienungsanleitung

LOFTNESS

LOFTNESS 601D1 Bedienungsanleitung

LOFTNESS

LOFTNESS 1082I Bedienungsanleitung

LOFTNESS

LOFTNESS 481EL Bedienungsanleitung

White Outdoor

White Outdoor 769-01923A Bedienungsanleitung