Toro 07297 Bedienungsanleitung

Printed in the USA

2001 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Canopy Kit

Workman1100/2100 and TwisterUtility Vehicle

Model No. 07297

Model No. 07297R

Form No. 3326-769 Rev B

Installation Instructions

Safety and Instruction Decals

Safety decals and instructions are easily

visible to the operator and are located near

any area of potential danger. Replace any

decal that is damaged or lost.

104-6731

Assembly

1. Position the machine on a level surface. Set the parking

brake, turn the ignition off, and remove the key.

If you leave the key in the ignition switch, someone

could accidently start the engine and seriously

injure you or other bystanders.

Remove the key from the ignition switch before

you do any maintenance.

Caution

2. If your vehicle has a Roll Over Protection System

(ROPS), proceed to step 3. If your vehicle does not

have a ROPS, proceed as follows:

A. Loosely attach the support brackets to the rear

support tube with 8 screws, 4 (5/16 x 2-3/4 in.) and

4 (5/16 x 1-3/4 in.); 16 flat washers (5/16 in.); and 8

flange nuts (5/16 in.) (Fig. 1).

B. Loosely attach the support brackets to the vehicle

with 8 screws (5/16 x 1 in.), 16 flat washers

(5/16 in.), and 8 flange nuts (5/16 in.) (Fig. 1).

3. Remove the rear bolt that holds the front fender to the

dash and front frame support on each side of the

vehicle. Do not remove the fenders from the vehicle

(Fig. 1).

Figure 1

1. Rear support tube

2. Left-hand support bracket

3. Screw, 5/16 x 2-3/4 in.,

and washer, 5/16 in.

4. Screw, 5/16 x 1-3/4 in.,

and washer, 5/16 in.

5. Flange nut and washer,

5/16 in.

6. Screw, 5/16 x 1 in,. and

washer, 5/16 in.

7. Left-hand front fender

8. Right-hand front support

9. Left-hand front support

4. Slide the slotted bracket on the front support between

the fender and vehicle. Loosely attach the front supports

to the floor of the vehicle using the existing hardware

on the vehicle (Fig. 1).

5. Secure the fenders with the bolts removed in step 3.

6. Loosely attach the canopy to the front supports using 4

long screws (5/16 x 2-3/4 in.), 8 flat washers (5/16 in.),

and 4 flange nuts (5/16 in.) (Fig. 2).

Note: The canopy support is already loosely attached to the

canopy (Fig. 2).

Figure 2

1. Canopy

2. Right-hand front support

3. Left-hand front support

4. Screw, 5/16 x 2-3/4 in.,

and washer, 5/16 in.

5. Flange nut and washer,

5/16 in.

6. Canopy support

7. If your vehicle has a ROPS, insert the clinch nuts into

the holes in the ROPS (Fig. 3). Lift the canopy and

attach it to the ROPS with 2 screws (3/8 x 1 in.) and 2

flat washers (3/8 in.) (Fig. 3). If your vehicle does not

have a ROPS, lift the canopy assembly and attach it to

the rear support tube with 2 screws (5/16 x 2 in.), 4

washers (5/16 in.), and 2 flange nuts (5/16 in.) (Fig. 4).

Figure 3

Vehicle with ROPS

1. ROPS

2. Clinch nut

3. Canopy

4. Screw, 3/8 x 1 in., and

washer 3/8 in.

Figure 4

Vehicle without ROPS

1. Rear support tube

2. Canopy

3. Screw, 5/16 x 2 in., and

washer, 5/16 in.

4. Flange nut and washer,

5/16 in.

8. Starting at the bottom of the vehicle and working your

way to the top, tighten all of the fasteners.

9. Adjust the front suspension; refer to Adjusting the Front

Suspension in the vehicle Operator’s Manual.

Dieses Handbuch passt für folgende Modelle

Andere Toro Nutzfahrzeug Handbücher

Toro

Toro 07385 Workman HDX-D Bedienungsanleitung

Toro

Toro Workman HDX Series Bedienungsanleitung

Toro

Toro Workman HD 07369 Bedienungsanleitung

Toro

Toro 07433LT Bedienungsanleitung

Toro

Toro 22979 Handbuch

Toro

Toro Workman MDE 2008 Bedienungsanleitung

Toro

Toro 7360 Bedienungsanleitung

Toro

Toro 7213 Bedienungsanleitung

Toro

Toro 7253 Bedienungsanleitung

Toro

Toro 7220 Bedienungsanleitung

Toro

Toro 07324 Bedienungsanleitung

Toro

Toro Workman GTX Bedienungsanleitung

Toro

Toro Workman 07369 Bedienungsanleitung

Toro

Toro Workman HD 07369 Bedienungsanleitung

Toro

Toro Workman GTX Bedienungsanleitung

Toro

Toro Workman MDX-D Bedienungsanleitung

Toro

Toro TX Platform Bedienungsanleitung

Toro

Toro 07252TC Workman 1100 Bedienungsanleitung

Toro

Toro Workman GTX Bedienungsanleitung

Toro

Toro 07277 Workman 2110 Bedienungsanleitung

Toro

Toro Workman MD Bedienungsanleitung

Toro

Toro 07253TC Bedienungsanleitung

Toro

Toro Workman MD Bedienungsanleitung

Toro

Toro 12004TC Twister 1600 Bedienungsanleitung

Beliebte Nutzfahrzeug Handbücher anderer Marken

Polaris

Polaris ACE 900 SP Bedienungsanleitung

TrailMax

TrailMax T-12-UR Bedienungsanleitung

Floe

Floe Cargo Max 9.5-73 Bedienungsanleitung

Taylor-Dunn

Taylor-Dunn B0-050-00 Handbuch

Taylor-Dunn

Taylor-Dunn ET 3000 Bedienungsanleitung

Kayo

Kayo S70 Bedienungsanleitung

Range Road

Range Road RR608 Bedienungsanleitung

Landoll

Landoll 900D Series Bedienungsanleitung

pronovost

pronovost PUMA-10000 Bedienungsanleitung

SSI SCHAEFER

SSI SCHAEFER WEASEL LITE Bedienungsanleitung

Club Car

Club Car TURF 272 2005 Handbuch

Cushman

Cushman Turf Truckster 84069 Bedienungsanleitung

BERG

BERG Large Trailer Bedienungsanleitung

Cub Cadet

Cub Cadet Big Country 641 Bedienungsanleitung

Westward

Westward Go-4 XTR Bedienungsanleitung

Club Car

Club Car Carryall I 1999 Bedienungsanleitung

Etnyre

Etnyre Street Flusher Bedienungsanleitung

Landoll

Landoll 340 Bedienungsanleitung